1. Manuals
  2. Brands
  3. VISSCHER Manuals
  4. Garden Houses
  5. Vista Leisure Series
  6. Manual

VISSCHER Vista Leisure Series Manual

9'x9' louver
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Vista Leisure Series and is the answer not in the manual?

Questions and answers

Related Manuals for VISSCHER Vista Leisure Series

Summary of Contents for VISSCHER Vista Leisure Series

  • Page 4 COMPLETELY PREPARED. THIS INCLUDES MAKING THE GROUND LEVEL, AND CREATING A FOUNDATION IF REQUIRED. MAKE SURE THAT THE AREA IS THE CORRECT DIMENSIONS FOR YOUR STRUCTURE. VISSCHER SPECIALTY PRODUCTS WILL NOT BE RESPONSIBLE FOR ANY INCORRECT INSTALLATION OF THIS PRODUCT.
  • Page 5 Step One Mt. SAINT BRUNO Vista Leisure Series - 9x9 Louver Promo Louver Panel (dc-1035) Louver Panel (dc-1035) Post (dc-1050) BEGIN ASSEMBLY WITH THE LOUVER WALL PANELS (DEALER CODE 1035). ATTACH TWO POSTS (DEALER CODE 1050) TO ONE LOUVER PANEL PLACING THE POST TIGHT ON THE INSIDE OF THE POST AS SHOWN.
  • Page 6 Step Two Mt. SAINT BRUNO Vista Leisure Series - 9x9 Louver Promo PLACE THE SECOND LOUVER PANEL AGAINST THE LEFT SIDE POST. ATTACH IT TO THE POST WITH FOUR 21/2" SCREWS. 2 1/2" ROBERTSON SCREWS 4 req...
  • Page 7 Step Three Mt. SAINT BRUNO Vista Leisure Series - 9x9 Louver Promo ONCE BOTH PANELS ARE ATTACHED TO THE POSTS SECURE THE CORNERS WITH THREE 2 1/2" SCREWS THROUGH THE TOP CORD INTO THE ADJACENT PANEL AS SHOWN IN DETAIL 1. THEN PLACE THE TWO 106" TRUSS FRAMES (DEALER CODE 1326) AT THE FRONT AND SIDE OF THE STRUCTURE ON TOP OF THE POSTS ATTACH THE TRUSS FRAME WITH THREE 2 1/2"...
  • Page 8 Step Four Mt. SAINT BRUNO Vista Leisure Series - 9x9 Louver Promo MEASURE GAZEBO WALL TO CHECK IF WALLS ARE SQUARE BEFORE PUTTING ON THE ROOF. MEASURE FROM POINT A TO POINT D AND THAT MEASUREMENT SHOULD EQUAL POINT B TO POINT C. ADJUST WALL UNTIL THEY DO.
  • Page 9 Step Five Mt. SAINT BRUNO Vista Leisure Series - 9x9 Louver Promo ONCE THE STRUCTURE IS SQUARED ATTACH THE TWO CORNER BRACKETS INTO THE ONCE YOU HAVE SQUARED THE TRUSS FRAME ATTACH THE 34" TRUSS FRAME CORNERS ONE THE OPEN SIDES AGAINST THE POST AND BOTTOM OF THE TRUSS SUPPORTS (DEALER CODE 1304) TO HOLD THE TRUSS FRAME ASSEMBLY SQUARE AS FRAME.
  • Page 10 Step Six Mt. SAINT BRUNO Vista Leisure Series - 9x9 Louver Promo PLACE THE 2x6 PEAK SUPPORT (DEALER CODE 1170) ON THE GROUND WITH THE SERIAL NUMBER TAG FACING UP. PLACE EACH OF THE COMMON RAFTERS (DEALER CODE 1674) AS SHOWN.
  • Page 11 Step Seven Mt. SAINT BRUNO Vista Leisure Series - 9x9 Louver Promo PLACE HIP RAFTERS (DEALER CODE 1673) IN PLACE AS SHOWN IN SECTION DETAIL AND TOP VIEW. (PLACE WITH OUTSIDE BOTTOM POINTS OF THE RAFTER FLUSH WITH THE BOTTOM OF THE SUPPORT).
  • Page 12 Step Eight Mt. SAINT BRUNO Vista Leisure Series - 9x9 Louver Promo PLACE A LEFT AND RIGHT PANEL SUPPORT (DEALER CODE 1321 & 1322) ON TOP OF THE WALLS AS SHOWN. PLACE THE PANEL SUPPORT SO THE ANGLE AT THE FRONT IS LINED UP FLUSH WITH THE TOP OF ALL THE RAFTERS.
  • Page 13 Step Nine Mt. SAINT BRUNO Vista Leisure Series - 9x9 Louver Promo PLACE THE ROOF STRAPPING ON TOP OF THE ROOF RAFTERS AS SHOWN. USE THE 2x4 TOP BEVELLED PIECE (DC-1437) AND THE 2x6 TOP BEVELLED PIECE (DC-1460) AT THE TOP OF THE RAFTERS, TIGHT TO THE PEAK SUPPORT.
  • Page 14 Step Ten Mt. SAINT BRUNO Vista Leisure Series - 9x9 Louver Promo SECURE THE COMMON RAFTERS ON EACH SIDE WITH TWO 3" HEX HEAD SCREWS AS SHOWN IN DETAIL 1 BELOW. SECURE THE RAFTERS IN PLACE WITH SCREWS THROUGH THE OUTSIDE OF THE TRUSS FRAMES ON ALL FOUR SIDES.
  • Page 15 Step Eleven Mt. SAINT BRUNO Vista Leisure Series - 9x9 Louver Promo PLACE THE FOUR PLASTIC ROOFING SHEETS ON THE ROOF STRAPS AS SHOWN. LAY THE PIECES OUT EVENLY. PLACE THE SHEETS SO THAT THEY EVENLY OVERHANG THE BOTTOM OF THE ROOF AND LEAVE ROUGHLY 1/2"...
  • Page 16 Step Twelve Mt. SAINT BRUNO Vista Leisure Series - 9x9 Louver Promo PLACE THE METAL HIP CAPS ON EACH CORNER OF THE ROOF AS SHOWN. PLACE EACH CAP SO ON TOP OF THE HIP OF THE ROOF. MAKE SURE THAT THE CAP IS SITTING CENTRED ON THE HIP, THEN ATTACH IT TO THE ROOF WITH TOP OF THE THE ROOF PANEL WITH ONE 1"...
  • Page 17 Step Thirteen Mt. SAINT BRUNO Vista Leisure Series - 9x9 Louver Promo PLACE THE PEAK CAP AT THE VERY TOP OF THE ROOF OVER TOP OF THE ENDS OF THE HIP FLASHING. AS SHOWN. SECURE THE HIP CAP WITH TWO SCREWS ON EACH SIDE THROUGH THE CAP AND INTO THE PLASTIC ROOFING.
  • Page 18 Step Fourteen Mt. SAINT BRUNO Vista Leisure Series - 9x9 Louver Promo ASSEMBLY OF THE BAR BEGINS BY PLACING THE 36" LEFT AND RIGHT BAR BRACES AGAINST THE INSIDE OF THE CORNER POST AS SHOWN. ATTACH THEM TIGHT TO THE INSIDE OF THE POST WITH THREE 2 1/2" SCREWS THROUGH THE BRACE PIECES AND INTO THE THE POSTS AS SHOWN.
  • Page 19 Step Fifteen Mt. SAINT BRUNO Vista Leisure Series - 9x9 Louver Promo PLACE THE BAR ASSEMBLE CENTERED ON THE LEFT AND RIGHT BAR LEGS AS SHOWN. ATTACH THE BAR TO THE LEGS WITH THREE 2 1/2" SCREWS AS SHOWN. PLACE THE CENTER BAR LEG UNDER THE MIDDLE OF THE BAR AS SHOWN.
  • Page 20 28" Stools Mt. SAINT BRUNO Step 1 Step 2 PLACE SIDE LEGS ON EITHER SIDE OF TOP AND PLACE SIDE LEGS ON EITHER SIDE OF TOP AND BOTTOM SUPPORTS AS SHOWN IN DIAGRAM. USE BOTTOM SUPPORTS AS SHOWN IN DIAGRAM. USE TWO 2 1/2"(6cm) SCREWS PER SIDE AS SHOWN.

This manual is also suitable for:

Mt. saint bruno

Table of Contents