Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Lightspeed Manuals
  4. Switch
  5. Access Link
  6. Registration manual

Lightspeed Access Link Registration Manual

Classroom communication hub
Hide thumbs Also See for Access Link:

Advertisement

Quick Links

Download this manual
ACCESS LINK REGISTRATION GUIDE
STANDARD REGISTRATION
FLEXMIKE REGISTRATION (OTHER REGISTERED COMPONENTS IN PLACE)
(Particularly valuable when Access Link is not easily accessible)
For users adding a second Flexmike or replacing a lost or malfunctioning Flexmike.
1.
Start with the Access Link plugged in and powered on.
2.
If replacing a Flexmike, make sure the malfunctioning Flexmike is powered off.
3.
If a second Flexmike, Sharemike or Media Connector is present, power it on
and wait until it has a solid blue light ("Ready"). (For the purpose of these
instructions, it is assumed that the #1 Flexmike is the functioning Flexmike and
we are registering the #2 Flexmike.)
4.
Power on the new Flexmike. Both microphone 1 and 2 blue lights should start
blinking.
5.
Open the new Flexmike battery compartment and pull the battery out (leaving it
plugged in) to reveal the registration button.
6.
Use another registered functional component (existing Flexmike, Sharemike or
Media Connector) to trigger the registration function in Access Link.
• Using a paperclip with the end straightened out, press and hold the registration
button for 3 seconds inside the functioning Flexmike. This triggers registration in
the Access Link and the Access Link's 1 and 2 amber lights will begin blinking.
7.
Briefly press the registration button on the new or replacement Flexmike. The 1 and 2 blue lights will start blinking alternately.
8.
After several seconds, the 2 light on the Access Link will turn solid
and the 2 light on the Flexmike will remain blinking, then turn
solid.
9.
The registration is complete. You can begin speaking into the new
Flexmike to verify there is audio.
10.
Place system ID number (attached to the Access Link Quickstart
Guide) on the new Flexmike.
NOTE: if at any point, the Access Link or Flexmike lights begin
blinking rapidly, that indicates a registration error. Turn the new
Flexmike off and repeat steps 4-9.
Solid light
Power On
(Existing Good Flexmike)
Blinking lights
MICROPHONE
AUDIO IN
TONE
POWER
1
2
MIN
MAX
MIN
MAX
TREBLE
BASS
MICROPHONE
AUDIO IN
TONE
POWER
1
2
MIN
MAX
MIN
MAX
TREBLE
BASS
USB POWER
5V/0.2A
REGISTER
USB POWER
+
MIC
LINE
5V/1.5A
AUDIO IN
BAL. AUDIO OUT
AUDIO OUT
AUDIO OUT/DC IN
Blinking lights
Power On
(NEW Flexmike)
Registration
Button
Solid lights
Apply to system components to indicate which parts are registered
as a system. Keep registered items together when storing away.
334-0162-02-00-01
00-01
00-01
00-01
00-01
00-01
00-01
00-01
00-01
00-01
00-01
RETAIN EXTRA LABELS IN THE EVENT A COMPONENT IS REPLACED OR ADDED.
Registration ID Labels
10101
00-01
00-01
00-01
00-01
00-01
00-01
00-01
00-01
00-01
00-01
00-01
00-01
00-01
00-01
00-01
00-01
00-01
00-01

Advertisement

loading
Need help?

Need help?

Do you have a question about the Access Link and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Lightspeed Access Link

Summary of Contents for Lightspeed Access Link

  • Page 1 • Using a paperclip with the end straightened out, press and hold the registration button for 3 seconds inside the functioning Flexmike. This triggers registration in the Access Link and the Access Link’s 1 and 2 amber lights will begin blinking. Registration Button Briefly press the registration button on the new or replacement Flexmike.
  • Page 2 Registration Button Using a paperclip with the end straightened out, briefly press the registration button on the back of the Access Link. The 1 and 2 lights will begin blinking on the Access Link. Briefly press the registration button on the Flexmike. The 1 and 2 lights will start blinking alternately.
  • Page 3 Flexmike is the the existing registered component.) Registration Button Blinking lights • The 1 and 2 amber lights will begin blinking on the Access Link. • Briefly press the registration button on the Sharemike. The Sharemike’s MICROPHONE AUDIO IN TONE POWER 1 and 2 lights will start blinking alternately.
  • Page 4 3 seconds inside the registered Flexmike. Button • The 1 and 2 amber lights will begin blinking on front of the Access Link. Briefly press the registration button on the Media Connector. The REGISTER light will begin blinking. Blinking lights...
  • Page 5 Briefly press the registration button on the Activate. The REGISTER light will begin blinking. After several seconds, the #1 light on the Access Link will turn solid. The LINK light on front of the Activate will begin blinking, then turn solid.
  • Page 6 00-01 00-01 00-01 00-01 00-01 00-01 NOTE: if at any point, the Access Link or Flexmike lights begin blinking rapidly, that indicates a registration 00-01 00-01 00-01 00-01 00-01 RETAIN EXTRA LABELS IN THE EVENT A COMPONENT IS REPLACED OR ADDED.
  • Page 7 Button Open the Sharemike battery compartment to reveal the registration button. On your mobile device, open the Lightspeed Activate app. Go to the ‘Settings’ tab and scroll down to find the ‘Register’ button and press the button. Tap the Mic 2 button to add/replace the Sharemike.
  • Page 8 00-01 RETAIN EXTRA LABELS IN THE EVENT A COMPONENT IS REPLACED OR ADDED. NOTE: if at any point, the Access Link or Pod lights begin blinking rapidly, that indicates a registration error. Power off the Pod, then repeat steps 3-6.

  • Page 9: Remote Registration

    17. Place system ID number (attached to the Access Link Quickstart Guide) on the new Remote Control. NOTE: if at any point, the Access Link or remote lights begin blinking rapidly, that indicates a registration error. Power off the remote, then repeat steps 4-6.
  • Page 10 BASS Mute After several seconds, the #1 light on the Access Link will turn solid and the Flexmike will have just one light blinking (1 or 2 Registration ID Labels Apply to system components to indicate which parts are registered depending on which microphone is being replaced) and then turn solid.
  • Page 11 Mute The center button on the remote will begin blinking and the 1 and 2 lights on the Access Link will be blinking alternately. Using a paperclip with the end straightened out, briefly press the registration button on the Sharemike. The 1 and 2 lights will be blinking alternately.
  • Page 12 Mute The center button on the remote will begin blinking and the #1 light on the Access Link will begin blinking. Using a paperclip with the end straightened out, briefly press the registration button on the bottom of the pod. The registration light will turn on.