X-Y Table (Optional); Mounting The X-Y Table To The Bus Bar Punch Unit; Exploded View - Greenlee 39693 Operation, Service And Parts Instruction Manual

X-Y Table (optional) (503 7736.1)

Assembly
1. Apply Loctite ® 242 or an equivalent to the threads
of two flat head screws (54). Use these screws to
attach one table track plate (53) to the positioning
table (40).
2. Apply Loctite 242 ® to two more flat head screws
(54). Attach the track spacer (52) and other table
track plate (53) to the bottom side of the "Y" posi-
tioning table (46). Use two button-head cap screws
(48), attach the bus bar guide (47) to the top side of
the "Y" positioning table (46). Slip the loop of the pin
lanyard (50) over the threaded screw of the short
revolving clamp (49), and mount the revolving
clamp (47) to the top of the bus bar guide (6).
®
3. Apply Loctite 242 to the remaining flat head screws
(54) and two socket head cap screws (44). Attach
adjustment plates (42 & 43) to the positioning base
plate (41) with the ten flat head screws (54). Mount
the positioning table decal (45) to the adjustment
plate (43) with the two socket head cap screws (44).
4. Place the positioning base plate assembly (41) over
the table track plate (53) mounted to the positioning
table (40). Secure with shoulder screw (56). Slide
"Y" positioning table assembly (46) into the slot on
the positioning base plate assembly (41). Insert the
pin with lanyard into one of the four holes in the bus
bar guide (47).
5. Attach the table operating decal (55) to the side of
the table.
48
47
46
45
44
43
42
41
40
57
Greenlee Textron / Subsidiary of Textron Inc.
Bus Bar Punch System
49
50
51
52
53
54
54
53
55
56
18

Mounting the X-Y Table to the Bus Bar Punch Unit

1. Remove yoke pin unit (C) and ram unit (A).
2. Clamp the bus bar punch yoke into a vise. Remove
the mounting plates (U) from the bus bar punch
yoke by removing four button-head screws (V); see
the exploded view.
3. Remove the punch alignment table (D) by removing
four button-head screws (V).
4. Attach the X-Y positioning table (40) to the bus bar
punch yoke (X) with the four button-head screws (V)
that were removed in step 3. Do not tighten the
screws.
5. Place any die in the die holder (T).
6. Adjust the X-Y table so that the table top is level,
and at the same height as the top of the die.
7. Tighten the four button-head screws (V).
8. Remove the bus bar punch unit from the vise.
Install the ram unit (A) and the yoke pin unit (C).
The yoke pin unit must fully engage the punching
yoke. The ball plungers of the yoke pin unit must
be visible at the back side of the punching yoke.
Key Part No. Description
40 503 7743.4 Positioning Table ...................... 1
41 503 7747.7 Positioning Base Plate ............. 1
42 503 7746.9 Adjusting Plate ......................... 1
43 503 7745.0 Adjusting Plate ......................... 1
44 905 4205.3 Socket Head Cap Screw .......... 2
45 503 7752.3 Positioning Table Decal ............ 1
46 503 7748.5 "Y" Positioning Table ................ 1
47 503 7749.3 Bus Bar guide ........................... 1
48 905 4193.6 Button-Head Cap Screw ........... 2
49 905 4195.2 Short Revolving Clamp ............. 1
50 503 7837.6 Pin with Lanyard ....................... 1
51 905 1434.3 3/8 Flat Washer ........................ 2
52 503 7751.5 Track Spacer ............................ 1
53 503 7750.7 Table Track Plate ..................... 2
54 905 4201.0 Flat Head Screw ...................... 14
55 503 9710.9 Table Operating Decal ............. 1
56 905 4194.4 Shoulder Screw ........................ 1
57 503 7752.3 Decal ........................................ 1
4455 Boeing Dr., Rockford, IL 61109-2988
Qty
815/397-7070