Page 1
Vehicle Security INSTALLATION MANUAL Model: PLUS-4700 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference; and (2) This device must accept any interference received, including interference that may cause undesired operation.
Step 1: Component Installation (Continued) Installing the Alarm Status LED: Find a suitable location for the LED and drill a 5/16" hole in the desired location. Feed the 2-pin plug through the hole and press the body of the LED into place. Run the LED wires to the location of the alarm control module.
Page 4
Step 2: 10-Pin Main Harness Installation (Continued) Brown Wire: (Siren + Output) Connect the brown wire to the positive wire from the siren. Ground the remaining wire from the siren for proper operation. Blue Wire: (Optional Grounding Sensor Input) The blue wire is an instant grounding trigger input for optional hood/trunk grounded pin switches or any electronic sensor.
Step 3: 5-Pin Power Harness Installation The power harness contains 3 wires and two vacant sockets. Follow the wiring recommendations enclosed for each wire. Power Harness First Socket Second Socket First Vacant Socket: The first vacant wire socket is a low current (300mA) grounded output wire that can be used to activate the vehicle’s interior lighting system when the security system is disarmed.
Step 4: Optional Accessory Connections Power Door Lock / Unlock Activation 3 Wire Positive Trigger Door Lock System 3 Pin Black Plug Black Wire: Connect to Lock Orange Wire: No Connection To Alarm Lock Control Switch Red Wire: Connect to Unlock (+) Lock Out +12 Volts Input To Door Lock...
Page 7
Step 4: Optional Accessory Connections (Continued) Mercedes Door Lock Activation Unlock Red Wire: Lock Door Lock Switch Orange Wire: No Connection Lock Lock Black Wire: Unlock To +12 Volts 3 Pin (Battery +) Black Plug Door Lock Unlock Compressor Newly Installed Power Door Lock Motors Red Wire: Lock Orange Wire: No Connection Black Wire: Unlock...
Page 8
Step 4: Optional Accessory Connections (Continued) Unlock Driver's Door First for 3-Wire Negative Door Lock Systems Red Wire Lock All Doors O r ange Wire Unlock Remaining Doors Black Wire Unlock Drivers Door Must Add +12V ALA984H Relay Passenger Drivers Door Switch Door Switch Lock...
Page 9
Step 4: Optional Accessory Connections (Continued) Starter Disable Wiring Using a Common Relay Using the wiring information and diagram below, connect the optional starter disable relay as follows: A. Locate the “Start Only Wire” coming from the ignition key switch and cut it. B.
Page 10
Step 4: Optional Accessory Connections (Continued) Flashing Parking Lights Headlight Switch Piggyback Parking Connection Red Wire with White Stripe Lights Output from Alarm Only Override Switch with 2-Pin Blue Plug: Dual-Zone Electronic Sensor Plug (Optional): Dual Zone Electronic Sensor Plug: (Applies to PLUS-4000 Only) Red Wire: +12 Volt Sensor Power Supply Black Wire: Sensor Ground Supply...
Page 11
Step 4: Optional Accessory Connections (Continued) Dome Light Supervision Using Optional ALA-RPT Relay Pack: Insert Black Wire into the First Socket Insert Red Wire into the Second Socket Orange Wire Output to Dome Light (+ or -) ALA-RPT Purple Wire Black Wire Relay Pack Input to Relay (+ or -)
Step 5: Transmitter Programming S t e p 1 S t e p 2 Override Switch Switch in Switch in “Off” Position “On” Position Plug In the Power Make Sure the Override Switch Harness is in the Off Position S t e p 3 S t e p 4 Flip the Override Switch Turn On Ignition...
Step 5: Transmitter Programming (Continued) S t e p 5 Regular Transmitter Passive Transmitter (Optional) Lock Lock Unlock Unlock Panic Panic Passive Unlocking Push Lock Button The LED will begin flashing slowly and the horn/siren will emit 1 short chirp. The code has now been learned. The transmitters supplied are pre-programmed to the receiver module.
Page 14
Step 6: Remote Feature Programming (Continued) Transmitter Button Function Confirmation = Change Function Chirp Status Indication 1 Beep = Chirp Status Indication “On” with Single Unlock Pulse * 2 Beeps = Chirp Status Indication “Off” with Single Unlock Pulse 3 Beeps = Chirps “On” with Dual Unlock Pulses On 4 Beeps = Chirps “Off”...
Step 7: General Testing To test the basic functions of the alarm system repeat the following procedures: 1. Turn off the ignition key and exit the vehicle closing all protected entrances. 2. Press the LOCK button on the transmitter. You will hear a siren/horn chirp, the parking lights will flash one time and the LED status indicator will flash at normal speed.
Page 16
Step 8: Speciality Feature and Optional Equipment Testing (Continued) Exit Valet Mode 1. Turn the ignition key to the “Off” position and open any door. 2. Press and hold down the UNLOCK + buttons. 3. The door locks will lock and unlock. Release the buttons. 4.
Page 17
Step 8: Speciality Feature and Optional Equipment Testing (Continued) LED Status Indicator Operation: LED is off = Alarm is disarmed. LED is flashing = Alarm is armed. LED is flashing in a 2 flash hold sequence = Tamper warning, alarm was triggered by the hood/ trunk or electronic sensor.
Step 8: Speciality Feature and Optional Equipment Testing Ignition Controlled Door Locking: (Door lock activation must be installed) When programmed on in “Remote Feature Programming”, ignition controlled locking is active 3 seconds after the ignition key is set the On position, the door locks will automatically become locked. When the ignition key is turned to the Off position, the door locks will unlock.
Page 19
PLUS-4700 Wiring Diagram Back View of Housing Shock Sensor Auxilliary Sensor Override Power Door Socket (White) Lock Power Door Lock Auxilliary Interrupt Harness Socket Socket (Orange) Override (Black) (See Optional Accessory Socket Connection) Black Wire (Blue) Plug-In LED Antenna (Do Not Ground)
Need help?
Do you have a question about the PLUS-4700 and is the answer not in the manual?
Questions and answers