Subscribe to Our Youtube Channel
Related Manuals for Carbine PLUS-4500
Summary of Contents for Carbine PLUS-4500
- Page 1 Vehicle Security INSTALLATION MANUAL Models: PLUS-4500 For Technical Assistance (800) 638-3600 For Fax on Demand Technical Assistance (800) 994-9977 (Must be a Registered Dealer to Use Fax on Demand System) © Copyright 2000 Magnadyne Corporation...
-
Page 2: Table Of Contents
Failure to follow this procedure could cause some confusion with transmitter operation and or alarm function operation. The PLUS-4500 security system are packaged 2 different ways for maximum flexibility. Even though the systems are packaged 2 different ways they all contain the same module and installation harnesses. The following is how each model number is packaged: PLUS-4500: 4500 Alarm Module with no transmitters and no siren. -
Page 3: Step 1: Component Installation
Step 1: Component Installation (Continued) Mounting the Override / Valet Switch: Mount this switch in a hidden but accessible location within reach of the driver of the vehicle. Drill a 1/4” hole and use the nuts and washers provided to secure the switch. Run the wires from the switch to the alarm control housing location. -
Page 4: Step 2: 10-Pin Main Harness Installation
Step 2: 10-Pin Main Harness Installation (Continued) Green Wire: (Grounded Door Pin Switch Input) The green wire connects to the common wire of the vehicle that switches on the dome light. Normally this wire is located at one of the door jamb switches. For some vehicles it may be necessary to connect the green wire directly to the switched turn on wire at the dome light. -
Page 5: Step 3: 5-Pin Power Harness Installation
Step 3: 5-Pin Power Harness Installation (Continued) Red Wire: (Main Power Input) Connect the red wire directly to the (+) battery post for best operation of the alarm system. For best current sensing capability from the alarm’s current sensing circuit, connect the red wire to the constant power wire coming from the interior dome light. - Page 6 Step 5: Optional Accessory Connections 3 Wire Positive Trigger Door Lock System (Applies to PLUS-4000 Only) Lock Control 3 Pin Black Switch Plug Black Wire: Connect to Lock (+) Lock Out Orange Wire: No Connection +12 Volts Input To Door Lock Control Relays (+) Unlock Out Red Wire: Connect to Unlock...
- Page 7 Step 5: Optional Accessory Connections (Continued) Newly Installed Power Door Lock Motors Red Wire: Lock Orange Wire: No Connection Black Wire: Unlock Violet Wire To +12 Volts (Battery +) 3 Pin Black Plug White Wire Brown Wire To Ground ALA-DL1 Relay Pack Green Wire: Lock To Newly...
- Page 8 Step 5: Optional Accessory Connections (Continued) Starter Disable Wiring Using Optional ALA-RPS Relay Pack Using the wiring information and diagram below, connect the optional starter disable relay as follows: A. Locate the “Start Only Wire” coming from the ignition key switch and cut it. B.
- Page 9 Step 5: Optional Accessory Connections (Continued) Flashing Parking Lights Headlight Switch Piggyback Parking Connection Red Wire with White Stripe Lights Output from Alarm Only Valet / Override Switch with 2-Pin Blue Plug: Dual Zone Electronic Sensor Plug: (Applies to PLUS-4000 Only) Red Wire: +12 Volt Sensor Power Supply Black Wire: Sensor Ground Supply Blue Wire: Sensor Alarm Trigger Output...
- Page 10 Step 5: Optional Accessory Connections (Continued) Dome Light Supervision Using Optional ALA-RPT Relay Pack: Insert Black Wire into the First Socket Insert Red Wire into the Second Socket Orange Wire Output to Dome Light (+ or -) ALA-RPT Purple Wire Black Wire Relay Pack Input to Relay (+ or -)
- Page 11 Step 6: Transmitter Programming S t e p 1 S t e p 2 Valet/Override Switch Switch in Switch in “Off” Position “On” Position Plug In the Power Make Sure the Harness Valet/Override Switch is in the “Off” Position The siren will start sounding, the parking lights will flash and the LED will begin flashing S t e p 3...
- Page 12 Step 6: Transmitter Programming (Continued) S t e p 6 Regular Passive Code Hopping Lock Unlock Lock Unlock Unlock Panic Lock/ Panic Panic Passive Unlocking Push Lock Button The LED will begin flashing slowly and the horn /siren will emit 1 short chirp. The code has now been learned. The transmitters supplied are pre-programmed to the receiver module.
- Page 13 Step 7: Remote Feature Programming When the Carbine security system control module learns the transmitter operating code, a specific group of operating features are automatically programmed to a default setting. These default settings can be changed by following the enclosed procedure and using the consumer transmitter for programming.
- Page 14 Step 7: Remote Feature Programming (Continued) S t e p 5 Regular Passive Code Hopping Lock Unlock Lock Unlock Unlock Panic Lock/ Panic Panic Passive Unlocking # Transmitter Button Function Confirmation = Change Function LOCK Chirp Status Indication 1 Beep = Chirp Status Indication “On” 2 Beeps = Chirp Status Indication “Off”...
- Page 15 Step 8: General Testing To test the basic functions of the alarm system (all models) repeat the following procedures: 1. Turn off the ignition key and exit the vehicle closing all protected entrances. 2. Press the lock button on the transmitter. You will hear a siren chirp, the parking lights will flash one time and the LED status indicator will flash at normal speed.
- Page 16 Step 9: Speciality Feature and Optional Equipment Testing Override Operation: (Security System is Armed) 1. Enter the vehicle and the security systems will begin sounding at this point. Make sure that the valet/override switch is in the “off” position 2. Place the ignition key into the ignition switch and turn the ignition switch to the “on” position. 3.
- Page 17 Step 9: Speciality Feature and Optional Equipment Testing LED Status Indicator Operation: LED is off = Alarm is disarmed. LED is flashing = Alarm is armed. LED is flashing in a 2 flash hold sequence = Tamper warning, alarm was triggered by the hood/ trunk or electronic sensor.
-
Page 18: Specifications
Step 9: Speciality Feature and Optional Equipment Testing Ignition Controlled Door Locking: (Door lock activation must be installed) When programmed on in “Remote Feature Programming”, ignition controlled locking is active 3 seconds after the ignition key is set the on position, the door locks will automatically become locked. When the ignition key is turned to the off position, the door locks will unlock. -
Page 19: Wiring Diagrams
Wiring Diagram PLUS-4500 Back View of Housing Power Door Lock Power Door Lock Auxilliary Interrupt Harness Socket Socket (Orange) (Black) Sensor Valet Auxilliary Dip Switch L.E.D. (See Optional Accessory Connection) Shock Sensor Valet / Override Socket (White) Socket (Blue) Plug-In LED... - Page 20 11-19-99 Rev. F PLUS45IM...
Need help?
Do you have a question about the PLUS-4500 and is the answer not in the manual?
Questions and answers
How do we disable it. We have lost the fob and hard yo jump start the battery. The alarm won't go off
To disable the Carbine PLUS-4500 alarm without the fob, follow these steps:
1. Enter the vehicle and close all doors.
2. Turn the ignition key to the "ON" position.
3. Locate the Valet/Override switch.
4. Press and hold the Valet/Override switch until the alarm system turns off.
5. The LED indicator should turn on steady, indicating the system is in valet mode and the alarm is disabled.
This process puts the alarm in valet mode, preventing it from arming automatically.
This answer is automatically generated
@Mr. Anderson Thank you for responding. I don't know where the switch is. It is a 1998 Honda Civic. I have looked all around the steering wheel snd in the glove compartment.