Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Cembre B68M-P18
Summary of Contents for Cembre B68M-P18
- Page 1 FIG. / BILD 1 FIG. / BILD 2...
- Page 2 FIG. / BILD 3 FIG. / BILD 4...
-
Page 3: General Characteristics
Weighted root mean square in frequency of the acceleration the upper limbs are exposed to for each biodynamic reference axis. Tests carried out in compliance with the indications contained in EN ISO 5349-1/2 Standard, and under operating conditions much more severe than those normally found. B68M-P18 B68M-P18E B68M-P18T B68M-P18A Battery charger ASC30-36... -
Page 4: Description Of The Components
200,000 previous operating cycles. The pump can be connected to hydraulic heads produced by Cembre for compression (max. 230 kN), cutting and punching. Main components (Ref. to Fig. 2):... - Page 5 To replace the battery, press the release button (2) (Ref. to Fig. 5) and push the battery downward to unlock it. Insert a charged battery from the bottom by sliding it into the guides until it locks. (CB) Canvas bag: made from sturdy fabric, allows users to store the pump and accessories. ...
- Page 6 Control button (9) on the pump: rocker type switch, enables the control of the pump only when the remote controller is not connected: Push forwards for actuation and backwards for oil release. When a crimping head is used, press and hold the operating button (1) until the motor stops automati- cally.
- Page 7 3.4) Operation On the remote controller display the operator can view and change some of the pump’s setting using the touch button (Ref. to § 4). The display shows the operating mode and oil release settings of the pump at each start-up (start- ing with the display switched off...
-
Page 8: Cutting Operation
CUTTING OPERATION Press the start button: this activates the motor of the pump that feeds the P = 0 bar hydraulic head connected to it, pressurising the oil. Keep the button pressed until the cutting operation is complete. At the end of the cycle the display will show the maximum pressure reached (P = 325 bar At the end of the cycle, proceed with the phase of returning the oil to the... -
Page 9: Navigation Menu
(Ref. to § 4.3 for further details). Battery charge level. BATTERY No. of cycles performed. -29990 No. of cycles before scheduled recommended maintenance. Cembre logo, pump model. B68MP NR 16AW125 Pump serial no. Enabling/disabling the LED Worklights LED ON) (Ref. to § 4.4 for further details). - Page 10 (*) Screens 1-2-5-6-7-9 can be set as the “main screen” which is shown on the display at every use of the pump; to do this, when the pre- selected screen is displayed, hold the fi nger on the button (13) until BEEP a confi...
- Page 11 4.3) Choosing the "release mode" The phase of discharging the oil into the pump’s tank can be carried out in two diff erent ways, depending on the mode set in the menu: Associated Release Function mode pictogram By releasing the start button the oil is returned in full to the pump reservoir only following automatic shut-off...
- Page 12 Check the oil level and if necessary refi ll (Ref. to § 5.4). No. of cycles to maintenance reached; the pump continues to work however, it is recommended that it is sent to Cembre for 30001 REQUEST a complete overhaul (Ref. to § 6).
-
Page 13: Maintenance
Cembre. Output voltage of the pressure trans- Remove and re-insert the battery, if the problem persists, please contact Cembre. mitter is out of the pre-set range. The pump stops and doesn't re-start. Failure to reach the set pressure Repeat the work cycle;... - Page 14 5.2) Canvas bag To protect the pump from accidental damage and dust, it should be stored with its accessories in the special canvas bag provided and sealed well. Canvas bag type CVB-031: Size 620x300x320 mm (24.4x11.8x12.6 inches), weight 2,4 kg (5.3 lbs). 5.3) Storage Once the job has been completed always completely release the pressure of the oil by holding down the release button;...