Related Manuals for KTS-Electronic PULSE AR III
Summary of Contents for KTS-Electronic PULSE AR III
- Page 1 PULSE AR III Pulse Induction-based Metal Detector User’s Manual KTS-Electronic GmbH & Co. KG Germany...
-
Page 2: Table Of Contents
Indication of metal ............... 9 Usage of appropriate searchcoils ..........9 Rechargeable battery and charger..........11 Error signals ................12 Care ..................... 13 Legal notice ................13 Warranty ..................13 Contact ..................14 KTS-Electronic GmbH & Co. KG – PULSE AR III... -
Page 3: Introduction
PULSE AR III. To avoid possible operational errors please read this instruction manual with due care. We wish you much success with your new PULSE AR III and will be at your disposal, if any questions should arise. Your KTS Electronic Team 2. -
Page 4: Electronic Unit
Automatic zero balance. By pressing the RESET-button the device is aligned to the respective ground surface. FREQ.: Frequency setting controller – the smaller the item you are searching for, the smoother the adjustment must be. VOLUME: Volume control. KTS-Electronic GmbH & Co. KG – PULSE AR III... - Page 5 2. Socket for charger 3. Headphone socket Any commercial headphones with 6.3 mm jack can be plugged. If you use the headphones, the speaker is turned off. Matching, light-weight headphones are provided. KTS-Electronic GmbH & Co. KG – PULSE AR III...
-
Page 6: Search Process
During zero balance make sure, that there are no metallic objects near the searchcoil. This could cause a wrong adjustment and produce unwanted indicator effects (as the case may be repeat the Reset-procedure at another, metal-free spot). KTS-Electronic GmbH & Co. KG – PULSE AR III... -
Page 7: Id Metal Discrimination
– the measured values can diversify. The indicated values are guide values, which can be complemented with your own search routine. Please take not of explanations to error signals on page 12. KTS-Electronic GmbH & Co. KG – PULSE AR III... -
Page 8: Installation
Determine your own speed during the search. To search a large area without great expenditure of time we recommend a speedy pace (no jogging). KTS-Electronic GmbH & Co. KG – PULSE AR III... -
Page 9: Adjustment
8. Adjustment The metal detector PULSE AR III can be adjusted within a very short time. 1. With the menu knob you activate the metal detector. Select the desired sound volume. 2. Briefly press the Reset-button in order to obtain a zero balance which is necessary for a failure-free search. - Page 10 During the search you should hold the search frame between 20 to 50 cm over the soil. A higher distance to the soil reduces the chance of an indication of small and medium-sized metal objects. KTS-Electronic GmbH & Co. KG – PULSE AR III...
-
Page 11: Rechargeable Battery And Charger
The charged battery allows an operating time of approx. 4-8 hours. An additional inverter module can be used to charge the battery in the car. KTS-Electronic GmbH & Co. KG – PULSE AR III... -
Page 12: Error Signals
4. After the charging process is completed, remove the charging cable plug. The plug should be pulled out after every charging. Note: PULSE AR III is equipped with a quick-charger. To prevent damages on the rechargeable battery always pay absolute attention to the maximum charging time of 90 minutes. -
Page 13: Care
13. Care Your PULSE AR III is easy to clean, yet there are some aspects, which you should bear in mind, in order to receive the optimal functionality. Protect the electronic housing with a plastic bag in case you should get caught in the rain, fog or sandstorm. -
Page 14: Contact
9:00 am to 4:00 pm Copyright by KTS-Electronic GmbH & Co. KG, Moerfelden-Walldorf/Germany, 2016/06. A duplication or usage of visual and textual content of this publication is not allowed without explicit consent. KTS-Electronic GmbH & Co. KG – PULSE AR III V1.01...