Function Descriptions - Toshiba 48-1250 A Instruction Manual

TD Series
5.4.10 Fault History and Run Time
Fn Group
F075 Fault History #1, Latest Fault
F076 Time Stamp, Fault #1
F077 Date Stamp, Fault #1
Fault History #2,
F078
Previous Fault
F079 Time Stamp, Fault #2
F080 Date Stamp, Fault #2
F081 Fault History #3, Oldest Fault
F082 Time Stamp, Fault #3
F083 Date Stamp, Fault #3
F084 Run Time, Hours
F085 Run Time, K Hours
F086 Run Counts
F087 Run Counts, 10K times
Digital Solid State Soft Starter 48 - 1250A
Function
0, 1 - 27 (Fault #: see Fault
code list; 0: No fault history)
00.00-23.59 (hh.mm)
[hh = 00-23; mm = 00-59]
01.01 - 12.31 (MM.DD)
[MM = 01-12; DD = 01-31]
0, 1 - 27 (Fault #: see Fault
code list; 0: No fault history)
00.00-23.59 (hh.mm)
[hh = 00-23; mm = 00-59]
01.01 - 12.31 (MM.DD)
[MM = 01-12; DD = 01-31]
0, 1 - 27 (Fault #: see Fault
code list; 0: No fault history)
00.00-23.59 (hh.mm)
[hh = 00-23; mm = 00-59]
01.01 - 12.31 (MM.DD)
[MM = 01-12; DD = 01-31]
000.0 - 999.9 (hours)
0000 - 9999 (thousand hours)
0000 - 9999 (times)
0000 - 9999 (10 thousand times)

5.5 Function Descriptions

The unit is set at the factory with typical starting characteristics that perform well
in most applications.
Note: Customer must program motor FLA (F001) for unit to operate.
5.5.1 Motor and Overload Function Descriptions
F001 = Motor FLA
Factory Setting = 0
Range = 50 - 100% of Unit Max. Current.
Set the value of this function to the motor nameplate Full Load Amps
(FLA). Adjustments for service factor are not necessary when
programming this function. (See note below). If the motor nameplate
FLA is not available, use typical values as shown in NEC, NEMA
standard MG-1 or other reputable third party source (motor manufacturer,
etc.).
Note: To prevent adjusting the settings beyond the starter Max Amp rating, the range
of adjustment for the Motor Nameplate FLA will vary to reflect the Service
Factor as programmed into F002. At the default setting of 1.0SF, the full range
of adjustment from 50 - 100% of the Max Amp rating is available. For example
F002 = 1.15 to reflect a 1.15SF, the maximum FLA programmable into F001 will
be limited to 85% of the starter Max. Amp rating (100% - 15%).
Adjustment
Range
TD - Series
- 20 -
Setting Factory
Increments Setting
View Only 0
View Only 00.00 EST
View Only 01.01
View Only 0
View Only 00.00 EST
View Only 01.01
View Only 0
View Only 00.00 EST
View Only 01.01
View Only 0
View Only 0
View Only 0
View Only 0
Section
5.5.10
5.5.10
5.5.10
5.5.10
5.5.10
5.5.10
5.5.10
5.5.10
5.5.10
5.5.10
5.5.10
5.5.10
5.5.10