Displaying Information; Using The Wireless Lan Pc Card; Functions; Communication Mode - Toshiba TLP-T72 Owner's Manual

Using handy features (Continued)
I Displaying Information [Status display]
This displays information about the input signal, lamp use time, etc.
Press the button twice.
When the button is pressed once, the Setting display menu appears. Pressing
it again displays information p.53
is displayed. Press the button again to dismiss the display.
Item Description
Input Input source name
RGB signal mode RGB input mode
H-resolution Horizontal resolution (in bits)
V-resolution Vertical resolution (in bits)
H-frequency Horizontal sync frequency
V-frequency Vertical sync frequency
Sync Sync signal polarity
Signal format Y/P /P signal format
B R
Video mode Color method of video signal
Card type PC card type
Shutter speed of document
Shutter speed
imaging camera
Lamp time Time of lamp use
Version Firmware version
MAC address See page 60
p.60
SSID See page 34,61
p.34
DHCP See page 61
p.61
IP address See page 61
p.61
Subnet mask See page 61 p.61
Gateway See page 61
p.61
Notes
1: The mode of supported RGB signals
2: Same as the refresh rate of the computer signal.
3: Sync signal polarity shown as P (positive) or N (negative) for [H/V].
4: Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be
used as a counter of guaranteed lamp time.) When the time displayed approaches 1,500
hours, consult with a store about getting a TLPLW2 replacement lamp (sold separately)
prepared.
5: [Version] shows the version of the projector's internal control program. This version is
referred to for customer service, etc.
6: Displayed when wireless LAN PC card is being used.
Notes
• The displayed information will not be refreshed if the status changes. To refresh the
information, dismiss the display, then display it again.
• Conducting another operation while information is being displayed dismisses the
display.
. The table below shows what kind of information
"Yes": displayed, "No": not displayed
Video
Computer Y/P /P PC Card Camera
B R
S-video
Yes Yes Yes Yes
[Note 1]
Yes No No No
Yes No No No
Yes No No No
Yes No No No
[Note 2] Yes No No No
[Note 3] Yes No No No
No Yes No No
No No Yes No
No No No Yes
No No No No
[Note 4] Yes Yes Yes Yes
[Note 5]
Yes Yes Yes Yes
No No No Yes [Note 6]
, No No No Yes [Note 6]
p.61
[Note 6]
No No No Yes
No No No Yes [Note 6]
[Note 6]
No No No Yes
No No No Yes [Note 6]
p.69 is shown.
32

Using the wireless LAN PC card

Please read this chapter if the model you purchased includes a PC card slot.
I Functions
The following functions are available via wireless communications, when the wireless
LAN PC card and dedicated Wireless Utility software
are used.
Note: A wireless LAN PC card except the supplied one (or recommended by Toshiba) does
not work with this product. Please ask your dealer about the available wireless LAN PC card.
1) Displaying a computer's screen via the projector
The computer's desktop screen can be sent, as well as the screens of a variety of
software applications, to the projector for display.
Yes
No
2) Displaying an image saved on a computer via the projector
No
JPEG files can be sent to the projector for display.
No
3) Sending images taken with the projector's document camera to a computer
No
This function is for models equipped with document camera.
No
See "Sending the camera's images to a computer"
No
4) Operating the projector by means of a computer
No
Some of the same functions available from the remote control can be performed.
No
No
I Communication mode
Yes
This projector supports both Ad-hoc and Infrastructure Communication modes.
Yes
Ad-Hoc Communication Mode
Yes
No
No
No
No
No
No
For security reason, confirm the specifications of your computer for the distance that
the radio wave can reach. The coverage of this projector may vary, depending on the
computer and the surrounding environment. When tested with a PC manufactured by
Toshiba with built-in wireless LAN system, the coverage is approximately 60 m.
This figure is not guaranteed and should be considered as merely a guideline.
Infrastructure Communication Mode
Access point
Use the appropriate transmission mode for your network environment. The instructions
in this owner's manual assume that you will be using a simple ad-hoc communication
mode setup.
p.24
p.49
This is transmission mode to communicate
between wireless LAN equipment.
Wireless communication can be performed via
the simple configurations.
This function can only be used if the projector is
in range of the computer's wireless signals.
A mixed wireless and wired LAN can be created
To LAN, via access points. Connecting to the rest of the
world via a wired LAN or the Internet generally
Internet, etc.
requires a high level of security.
Hub
33
included with this projector
for details.