Connecting Your Coolbot Pro To Your Wi-Fi Network; Wi-Fi Configuration And Web App Set Up - Store It Cold CoolBot Pro Manual

CONNECTING YOUR COOLBOT PRO TO YOUR WI-FI NETWORK

CoolBot Pro and CoolBot Jumper Set Up
STEP 1 Unpack the CoolBot Pro in an area with good Wi-Fi reception (outside of your cooler and close to your Router is best). Plug
in the Temperature Sensors and the Heater Cable into the corresponding ports (See diagram on page 4). Don't connect the
cables to your A/C and don't plug in the power supply.
STEP 2 Connect the CoolBot Jumper to the CoolBot Pro using ONLY the provided silver/grey Data Cable. The provided Data Cable is
specific to the CoolBot Pro/Jumper – standard phone cable will not work and may damage your CoolBot Pro/Jumper.
In an area where your PC or phone get good Wi-Fi reception, plug in the CoolBot Pro's Power Supply. You should see codes
STEP 3
and flashing mode lights for several seconds. These should settle down to one flashing Program light, and the code "E0"
alternating with the current room temperature.

Wi-Fi Configuration and Web app Set Up

STEP 4 Start the CoolBot Pro App by scanning the QR Code on your smartphone or go to the web page
https://cb.storeitcold.com
is a web-based app and is not available from your mobile App Store.
On the first screen, fill in your email address, create a password and select "Create New Account".
STEP 5
The email address will be used for notifications, as well as to link your data to your account.
STEP 6 Continue to follow the prompts. The app will guide you through configuring the CoolBot Pro to talk to the CoolBot server
using your Wi-Fi Network. When prompted, you will need to change the Wi-Fi settings on your device (PC, tablet, smartphone,
etc.) to connect to the Wi-Fi Network called "CoolBot". On most smartphone use Settings > Wi-Fi, and on most PCs use the
network or Wi-Fi status icon.
STEP 7 Choose or type in the Wi-Fi Network you want the CoolBot to use. This is usually the same network your phone uses, but it
can be a different network if you prefer. Enter the Wi-Fi password for the network and press Next.
STEP 8 Once the CoolBot Pro is connected to the Network, you should see no codes (and no flashing) on the CoolBot Pro display.
If your device (PC, tablet, phone, etc.) did not automatically switch back to your usual Wi-Fi settings use the method outlined
in Step 6 to switch them back.
Press the "Refresh" button on your browser screen. You should now see temperatures on the app.
STEP 9
Putting the app icon on your home screen
STEP 10 On most devices you can add a link to your home screen for the CoolBot Pro App so you can access it just
like any other app. While in the CoolBot Pro App on your browser do the following:
• In Chrome on Android: Open the menu at the upper right and choose "Add to Home Screen."
• In Safari on iOS: Tap the Share button at the bottom of the screen and choose "Add to Home Screen."
• In most desktop browsers, you can drag the icon at the left of the URL bar at the top of the browser
and drop it onto your desktop to create a shortcut.
You may be prompted for your user ID and password the first time you access the App from the icon on the home screen.
You are all set up! Unplug your CoolBot Pro from the power supply and proceed to "INSTALLING YOUR COOLBOT PRO TO
STEP 11
YOUR A/C" Section of this Guide (page 3).
If you ever need to adjust the Data Cable or CoolBot Jumper placement, power down the CoolBot Pro before plugging or unplugging the
CoolBot Pro Quick Start Set Up Guide Rev 2019 – 03A
on a device that has Wi-Fi (PC, tablet, phone, etc.). The CoolBot Pro App
IMPORTANT!
Data Cable.
2 | P a g e
©2019 Store It Cold, LLC