12 Tracker software upgrading ....................... 71 12.1 Tracker software upgrading via USB .................. 71 12.2 Tracker software upgrading via USB with a firmware file ............ 71 12.3 Tracker software upgrade via GPRS .................. 72 Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
Page 3
Appendix А. Bits description for the «STATUS» field ..............74 Appendix B. WIALON system parameters description ..............75 Appendix C. CAN-LOG parameters description ..............77 Appendix D. ISO 9001:2015 ......................80 Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
Page 4
This Operation manual relates to the tracker ADM700 3G (hereinafter referred to as tracker) and describes the procedure of its installation and connection as well as its function and settings. The Operation manual is designed for professionals who have familiarized themselves with the rules of repair and installation works execution in vehicles and who have special professional knowledge in electronic and electric equipment used on various transport means.
The working time with the completely charged battery is 3 hours in the full- featured mode and 2 extra hours in the data saving mode. The working time may change Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
Page 6
⎯ voltage values in analogue inputs; ⎯ values from pulse inputs; ⎯ data about events occurred; ⎯ data from connected sensors; ⎯ discrete outputs condition; ⎯ device condition (see the Appendix A). Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
⎯ Number of discrete (pulse) inputs: 2 ⎯ Discrete (pulse) inputs features: operation mode: frequency meter, flowmeter (counter), discrete; maximum frequency: 3000 Hz; maximum quantity of pulses counted: 4294967295; activation by connection to the ground; Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
Page 8
⎯ Weight: not more than 250 g. In order to prolong battery service life its charging start only at 0°С temperature. Data transmission to the server start at temperature above -40°С. Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
− blinks twice: data from GLONASS/GPS module have been received but coordinates are not valid; − blinks once: GLONASS/GPS module has defined the time and the valid coordinates. Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
Page 10
⎯ is always lighting up and switching off for short moments: SIM-card is not available. See the contacts arrangement for MF-24F plug of the tracker in Figure 2. Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
(housing, GND). Contacts arrangement layout for MF-24 connector is provided in the Figure 2. It is necessary to install a 2A melting fuse between the positive ground of the vehicle Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
Page 13
10V to 40V of the direct current and at least the 1A current. Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
The tracker is controlled by means of commands sent via SMS, GPRS or USB. General rules for writing commands: ⎯ only Latin alphabetic characters and punctuation may be used in commands; ⎯ character case does not matter; Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
SIM card 0 and «SETGPRS1» for SIM card 1. Then set the IP-address and the server port (host) by the «SETHOST0» command or «DN0». These parameters change might be performed in graphical interface of ADMConfigurator program. Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
GLONASS/GPS module are transmitted. The vibration level threshold is installed by the «MAXACC» command. This mode activation is performed by the INSTATIC 15,1 command. Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
The minimum input resistance: 110kOhm IN1 input features: Voltage measurement range: 0-13,3V. Discreteness (sensitivity): 13mV. The minimum input resistance: 110kOhm. IN2-IN5 inputs features: Voltage measurement range: 0-36,6V. Discreteness (sensitivity): 36mV. Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
Page 18
The measured voltage levels values are registered by the tracker and transmitted to the server in the data block IN_A with a common periodicity. Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
The «Frequency meter» mode allows measuring the current signal frequency. It is used when connecting frequency output sensors. Connection layout for a fuel level output sensor is provided in the Figure 5. Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
7.2.2 «Flowmeter» mode «Flowmeter» mode allows counting pulses and saving data in the non-volatile memory. A layout for connecting two flowmeters to the tracker is provided in the Figure 6. Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
DIN1 (the difference is transmitted to the server instead of DIN0). DIN1 is transmitted without change. A layout for connecting a differential flowmeter to the tracker is provided in the Figure 7. Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
Discrete inputs have an inner pull-up to the plus. When connecting the discrete input to the variable voltage circuit, the logical “0” level will be defined based on voltage fewer than 1 V, and Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
A layout for a door limit switch connection is provided in the Figure 8. Figure 8 - Connection layout for a door limit switch (12 +U vehicle electrical network) 7.3 Discrete outputs OUT0-3 discrete outputs features: Output type – open collector Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
Page 24
The response to the «OUTPUT» command always displays the condition of four outputs: OUTPUT (3..0) = 0000. It is possible to make the output condition dependent on an event at the analogue input via «INTRUEOUT» command. Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
Page 25
Figure 9 — Connection layout of a relay to the tracker discrete output (12 +U vehicle electrical system) Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
Page 26
With the «SPEEDALARM» command set the speed value, which violation should be notified to the driver. SPEEDALARM X,Y Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
The current fuel level value is displayed in the response to the «FUEL» command. If necessary, the addresses of the sensors interrogated might be changed by the «LLS485 X,Y,Z» command. X,Y,Z are addresses of interrogated sensors and addresses 0,1,2 are interrogated by default. Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
«EUROSENSENABLED» defines the data set requested from the sensor. It is necessary to indicate the requested data codes and fields separating them with commas. The repeated command rewrites the preset parameters. Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
Page 29
Accumulated fuel amount in negative mode, 0.01 l ------------- 0x13 Accumulated fuel amount in supply Accumulated fuel amount in supply chamber in idle mode, 0.01 l chamber in nominal mode, 0.01 l Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
Connect RFID-reader ADM20 to the tracker RS-485 bus. Coordinate the work of the tracker and RFID-reader ADM20 (setting procedure is described in the p. 5 of the Operation Manual “Receiver/transmitter combination ADM20”) Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
RS-232 0 and RS-232 1. This setting is performed by the "SET232" command or in the graphical interface of the ADMConfigurator program, version 2.1 or higher. Command SET232 X, Y X is the port number Y - operation mode Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
The command «LLSTOIN X, Y» establishes the correspondence between the sensor address and the analog input number, instead of which the fuel level will be transmitted. X is the number of the analog input Y - sensor address Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
- connect the camera to any of the RS-232 ports; - set the required RS-232 port to the camera mode; - activate the connection with the camera using the command «CAMENABLED X». Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
«CAMUPLOADNUL» cancels the upload to the server of all photos on the memory card that are in the transmission queue. 7.5.3 CAN-LOG connection To connect the CAN-LOG, do the following: Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
Figure 14 – Connection layout of CAN-LOG to the RS-232 interface (12 +U vehicle electrical system) 7.5.4 Autotracker fuel level sensors connection To connect the Autotracker fuel level sensors, do the following: - connect the fuel level sensors to any of the RS-232 ports; Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
To start uploading the DDD file from the tachograph to the monitoring system via GPRS, you should send the «TACHOGETDDD X» command, where X is the card slot number. Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
To request the readings from any of the sensors connected to the 1-Wire bus, enter the «OWTHERMO X» command, where X is the sensor serial number (0 ... 7). Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
When this correspondence is found, the tracker plays the respective sound file. The layout for identifying the zone for playing the audio file is shown in Figure 16. Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
(the total resistance of the simultaneously connected loudspeakers is not less than 8 ohms) and insert the common wire into the tracker self-clamping plug. The connection layout is shown in Figure 17. Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
Page 40
It also allows to use the previously installed voice announcement system, if the system allows the connection of external signal sources. The input resistance of the audio power amplifier should be 10-50 kOhm. Schematic diagram of the connection is shown in Figure 18. Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
1. Format microSD memory card into FAT32 file system. MicroSD memory cards up to 32 Gb are supported. 2. Make sure audio files format correspond to the following requirements: Format: wav Sampling frequency: 8кHz Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
Page 42
Final line should be strictly empty. Example of «route.txt» file is given in Figure 19. Coordinates data can be received from dispatch program of the vehicle that have earlier passed this route. Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
“Autoinformer” operates using «ROUTETEST» command. After the receipt of such a command, audio file, which have been indicated in the first line of «route.txt» file of active route, will be reproduced. Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
There is no need for additional resistor if resistance is ~60Ohm. As a rule, while connecting to diagnostic connector there is no need to use a resistor. When connecting to Can bus use connection layout given on Figure 21. Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
Page 45
Figure 20 – Connection of tracker to CAN bus diagnostic connector (12 +U vehicle electrical system) Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
Page 46
Figure 21 — Connection of tracker directly to Can bus (12 +U vehicle electrical system) Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
Figure - 22 Setting of messages filter for CAN bus 9.2.1 Manual setting For manual setting do the following: ⎯ install TAG field number “CAN” where value is transmitted to the server (0...15); ⎯ enter message identifier (ID); Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
«PROTOCOL» command or in a graphic interface of ADMConfigurator program. 10.2 Acceleration and braking values transmission To estimate driving quality the tracker allows transmitting speed change values (km/h) in 1 Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
«1» and logical “0” therefor. The tracker will pass to the guard mode if the voltage values in this input are set within the logical “1” range. Deactivation of such an arming mode is performed by the «INGUARDMODECLEAR» command. Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
X – password by default “0” PHONES X PHOES (0)= (1)= (2)= (3)= Request of authorized phone numbers list. Example: PHONES 1234 Example: PHONES (0)= (1)= +79876543210 (2)= (3)= Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
Page 51
0). The command without parameters Y — login by default SETGPRS0 internet.mts.ru, Example: restores to the current settings GPRS for SIM- mts,mts GPRS: APN=internet.mts.ru, Y=beeline; card. Z – password by default user=mts, pass=mts Z=beeline. Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
Page 52
Setting timeframe between attempts to connect Example: WAITTIME 5 Example: Wait Time = 5 By default Y=0 to the server via GPRS when there is no connection. Y=0 – sets automatic adjustment of track parameter. Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
Page 53
When such a command is being done current number of data packet is being reduced to zero and the tracker is being rebooted. ERASE EEPROM ERASE EEPROM Command without Restoring of manufacturer settings and tracker parameters rebooting. Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
Page 54
X=255 – function disabled Example: Example: be transmitted from LLS Omnicomm sensor Y=0,..255 – address of the LLSTOIN 2,34 LLS 34 CONNECT TO INPUT sensor which data should be transmitted from Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
Page 55
Setting an averaging interval according to input. Y =20..60000 – values in Example: Example: Voltage value according to input is averaged INFILTER 1,1000 INPUT 1 FILTER TIME 1000 milliseconds within the set time. By default Y=5000 Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
Page 58
Input 2: InTrue 8000..15000, ININFO 2 InFalse 0..3000, InGuardMode 0, InTrueSms 2, SmsTxt ‘ALARM‘ Guard on Guard On Arming Guard off Guard Off Disarming Alarm Off Alarm Off Alarm deactivation Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
Page 59
GPS3D=X Setting GLONASS/GPS receiver mode. X=1 – mode 3D, Example: Example: In 3D mode all improperly determined MODE 1 MODE 1 by default X=1. coordinates will be transmitted as invalid. Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
Page 60
Choosing of a current route for autoinformer Example: ROUTE 15Т Example: ROUTE '15Т’ route ROUTOFF ROUTOFF Switching off autoinformer function ROTETEST ROUTETEST playing... Command without Reproducing of first active route audio file. parameters Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
Page 61
X=1 - EGST protocol. X – phone number in NUMBER X IDN 1234 IMEI IMEI and device number request «7xxxxxxxxxx» format 354123456789012 The answer is sent via SMS to the indicated phone number Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
Page 62
SD OFF in the device works well at valid settings. X – tag number CANDATA X CANDATA X Displaying of CAN tag value. Example: CANDATA 1 Example: CANDATA_1 = 1F Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
Page 63
Handling tracker output. Command without Example: Example: to the ground) parameters restores to the output current X=0 – output is not active OUTPUT 1 OUTPUT 1 settings. (disconnected from the ground). By default, =0. Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
Page 64
Setting of input number which data will be X=255 – input number is not Example: DSPTOIN 2 Example: DSPTOIN 2 substituted by transmission of the vehicle state defined (value is set by data. default ) Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
Page 65
X,Y,Z – LLC sensors LLS485 X,Y,Z LLS485 X,Y,Z Installation of LLC sensors addresses Example: LLS485 3,20,55 Example: LLS485 3,20,55 addresses connected to the tracker via the RS485 interface Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
Page 66
CAMUPLOADSIZE CAMUPLOADSIZE Displays the number of not uploaded photos, Example: CAMUPLOADSIZE Example: CAMUPLOADSIZE pcs. CAMUPLOADNUL CAMUPLOADNUL Marking of all photos as uploaded ones Example: CAMUPLOADNUL Example: CAMUPLOADNUL Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
Page 67
(speed change (km/h) per 1 second). Y – braking limit activating Installing acceleration and braking limits the output; activating the tracker output. – acceleration limit activating the output; А – activated output number Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
Page 68
X=0 tachograph VDO; X=1 Choosing type and port of the tachograph being Example: Example: tachograph SHTRICH-М; connected. TACHOENABLED 1,2 TACHOENABLED 1,2 X=0 RS-232_0 port; Y=1 RS-232_1 port; Y=2 RS-485 port. Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
Page 69
Including EUROSENSE DELTA RS sensor Y – requested field X0,Y0,X1,Y1 X1:Y1 support, transmitted data set installation Example: Example: EUROSENSENABLED EUROSENSENABLED 0x00,1,0x01,3 0x00:1,0x01:3 EUROSENSVALUES Command without parameter Displaying of set EUROSENSE sensor parameters value Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
Page 70
Giving sequence numbers for all devices on 1- DS1820 ) 1:(Thermometer - Wire bus. DS18B20 ) OWCONFIGINFO Command without parameter Displaying of all devices on 1- Wire can and giving- them sequence numbers. Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
⎯ drag the firmware file in the respective field in the сonfigurator window; ⎯ ⎯ after the firmware is upgraded, the tracker will be rebooted and become available for work. Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
When there are signs of oxidation or other proofs of liquid penetration in the device housing; ⎯ a tracker without housing; ⎯ a track with signs of repair performed beyond the manufacturer's service center; Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
Battery high voltage indicator 2048 Sign of using microSD card as “black box” 4096 Case opening detected 8192 Coordinates are defined by GSM base stations 16384 Headset button is pressed 32768 Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
Condition of discrete sensor set for D_IN1 input Tracker reboot indicator in10 Active SIM card number in11 No connection to the server in12 Guard mode enabled in13 Battery low voltage indicator Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
Page 76
Coordinates are defined by GSM base stations in24 Headset button is pressed out1 Tracker output OUT0 activated out2 Tracker output OUT1 out3 Tracker output OUT2 out4 Tracker output OUT3 Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
Appendix C. CAN-LOG parameters description Table C.1. Description of parameters transmitted in the Wialon system when connecting CAN-LOG to ADM700 3G Parameter Name Unit of measurement can0 E_cons total fuel consumption liter can1 H_RPM Engine rmp 50/min can2 I_temp Engine temperature...
Page 78
Dynamic ignition * information is available when ignition is on Table C.3. Description of certain «agricultural machinery status» parameter bits: Bit No. harvester grain release from the hopper Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
Page 79
Main beam check engine external lighting pressure in cans brake blocks wear warning low fuel level STOP pressure/oil level engine coolant temperature Braking system Battery charge Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018...
Need help?
Do you have a question about the ADM700 3G and is the answer not in the manual?
Questions and answers