PRESIDENT MARTIN ASC Owner's Manual page 29

6) EMERGENCY CHANNELS ~ EMERGENCY CHANNEL SETTING
VOX ~ VOX SETTING
EMERGENCY CHANNELS
Emergency channels will be automatically
(8). First press : emergency channel 1 is activated. Second press: emergency
channel 2 is activated. Third press: return to the current channel. "EMG"
appears on the display when an emergency channel is activated.
The default emergency channels are channel 9/AM (1) and channel 19/
AM (2).
Note: Activating a emergency channel
mode (AM / FM / UK) or enable/disable
function is activated, an error beep sounds (see § KEY BEEP page 30).
EMERGENCY CHANNEL SETTING
customized
Emergency channels can be
1. Short press the EMG key (6) until
modified.
2. Long press during one second the EMG key (6).
"EMG" blinks.
3. If necessary, use the MODE key (8) to
FM or FM UK (in U configuration only)
4. Turn the ROTARY knob (4) the
5. Press PTT switch (11) to store and exit. If the KEY BEEP function is activated,
an long beep sounds to confirm
BEEP page 30).
6.
If no key is pressed for 5 seconds, the unit automatically
CHANNEL without save.
VOX
(long press)
The VOX function allows transmitting
phone (or in the optional vox microphone) without pressing the PTT switch
(11). The use of an optional vox microphone connected to the rear panel
disables
of the transceiver (C)
Long press the VOX key (6) in order to
appears on the display. Long press again the VOX key (6) to
function. "VOX" disappears.
VOX SETTING
(combination F + VOX)
1. Press the F key (7), then press the VOX key (6) to
"VOX" blinks, the current setting and its value appear on the display. Three
(short press)
selected by pressing the EMG key
prevents
changing the modulation
the VOX function. If the KEY BEEP
(modulation mode and channel).
activated
the emergency channel to be
appears on the display,
change the modulation mode: AM,
select the emergency channel
the success of the operation (see § KEY
exits EMERGENCY
by speaking into the original micro-
the original microphone.
activate the VOX function. "VOX"
disable
enter the VOX SETTING.
parameters allow to adjtust the VOX: Sensitivity L / Anti-vox level A / Vox
delay time t.
2a. Turn the ROTARY knob (4) or use the UP/DN key (12) on the microphone
to modify the current parameter then, press the F key (7) to
parameter or....
2b. Press fist the F key (7) to
ROTARY knob (4) or use the UP/DN key (12) on the microphone to
the current parameter.
3. When all adjustments are done, press PTT switch (11) to
KEY BEEP function is activated, an long beep sounds to
of the operation (see § KEY BEEP page 30).
4.
If no key is pressed for 5 seconds, the unit automatically
VOX SETTING without save.
Sensitivity L: allows the adjustment of the microphone (original one or
-
optional vox) for an optimum transmission quality. Adjustable level from1
(high level) to 9 (low level). Default value: 5.
Anti-Vox A: allows disabling the transmission generated by the surrounding
-
noise. The level is adjustable. AF (according the squelch level) and from 0
(without anti-vox) to 9 (low level). Default value: AF.
- Delay time t: allows avoiding the sudden cut of the transmission by adding
a delay at the end of speaking. The level is adjustable from 1 (short delay)
to 9 (long delay). Default value: 1.
VOX SETTING doesn't activate the VOX function.
7) F
(short press)
Allows to set/validate
This key pressed alone don't have any use.
See § FREQUENCY BAND SELECTION page 31.
8) MODE ~ ANL
MODE
(short press)
Press MODE key (8) to
mode is displayed on LCD.
Your modulation mode has to correspond to the one of your correspondent.
- Frequency Modulation / FM: for nearby communications on a flat open
the
field.
- Amplitude Modulation / AM: communication on a field with relief and
obstacles at middle distance (the most used).
In U configuration only: The MODE key (8) allows to
frequency band. "UK" is displayed when the ENG frequency band is se-
29
select another the parameter and then turn the
store
confirm
functions (see for example § VOX SETTING above).
select
the modulation mode: AM or FM. Selected
select
select next
modify
and exit. If the
the success
exits
the function
the ENG or CEPT