Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Digi One IAP Haz
Summary of Contents for Digi One IAP Haz
- Page 1 Digi One IAP Family Digi One IAP and Digi One IAP Haz User Guide...
- Page 2 Information in this document is subject to change without notice and does not represent a commitment on the part of Digi International. Digi provides this document “as is,” without warranty of any kind, expressed or implied, including, but not limited to, the implied warranties of fitness or merchantability for a particular purpose.
-
Page 3: Table Of Contents
Additional software, utilities, and other resources on Digi website Configure the Digi One IAP using IA profiles About IA configuration profiles Key terms in IA configuration profiles Serial bridge profile: master and slave connected to Digi ports Modbus profile: serial-connected slave Modbus profile: serial-connected master DF1 profile: serial-connected slave... - Page 4 Run diagnostics Interpreting the status LEDs Hardware information Hardware specifications Regulatory information International EMC (Electromagnetic Emissions/Immunity/Safety) standards Safety considerations and warnings Environmental considerations and cautions Digi One IAP Family User Guide...
-
Page 5: About The Digi One Iap
Easy management through SNMP Flexible Industrial Automation support The Digi One IAP support for IA protocols is exceedingly flexible, providing connectivity solutions in a wide variety of industrial automation environments. It supports the following: Multi-mastering, which means that a slave using any supported serial port protocol can be managed by multiple masters;... -
Page 6: Serial Port And Network Protocol Support
Serial port protocol Network protocols Multi-master support Modbus ASCII and Modbus/TCP Modbus RTU TCP Sockets UDP Sockets RealPort COM Port redirection Digi One IAP Family User Guide... -
Page 7: Package Contents
Digi Technical Support for additional testing or diagnostic procedures. A DB9-to-DB9 cable to connect a PC or laptop to the serial port, enabling you to access the Digi One IAP command line to configure the device. About the Digi One IAP documentation This guide provides all the information most users need to set up the device server for industrial automation applications. -
Page 8: Other Guides And References
Digi website, provides complete descriptions of all commands. Additional software, utilities, and other resources on Digi website In addition to the user documentation, the following utilities and software for working with your Digi One IAP are available on the Digi website (www.digi.com): Digi Device Discovery Utility, a utility that enables you to discover all Digi devices on our network and configure an IP address. -
Page 9: Configure The Digi One Iap Using Ia Profiles
There are several port profile choices for the Digi One IAP, on the Serial Port Configuration page of the web interface. If a port profile has already been selected, it appears at the top of the Serial Port Configuration page in the web interface. -
Page 10: Serial Bridge Profile: Master And Slave Connected To Digi Ports
Configure the Digi One IAP using IA profiles Serial bridge profile: master and slave connected to Digi ports Term Description multi-master Any configuration in which more than one master simultaneously communicates with a slave. protocol request A message generated by the master and sent to... -
Page 11: Modbus Profile: Serial-Connected Slave
Omron FINS Omron CompoWay/F A serial port protocol that meets Digi’s definition of a “user defined” protocol, that is, one that has fixed header and trailer strings that bound all message packets and where each protocol request is followed by a single response. -
Page 12: Modbus Profile: Serial-Connected Master
Modbus RTU or Modbus ASCII. If the remote slave supports TCP socket communication, which is the case if the remote slave is connected to another device server, Digi recommends this option. Modbus/TCP is the other supported network option. This master can be configured to control up to 8 slaves. -
Page 13: Df1 Profile: Serial-Connected Master
DF1 Full-Duplex. If the remote slave supports TCP socket communication, which is the case if the remote slave is connected to another device, Digi recommends this option. For DF1 Full-Duplex users, Allen Bradley Ethernet and Ethernet/IP are other supported network options. -
Page 14: Omron Family Profile: Serial-Connected Master
The serial port connection must be configured for the protocol required by the master, in this case Hostlink, FINS, or CompoWay/F. If the remote slave supports TCP socket communication, which includes a slave connected to another device server, Digi recommends this network option. UDP Sockets is another supported network option. -
Page 15: Other Serial Port Protocol Profile: Serial-Connected Slave
Configure the Digi One IAP using IA profiles Other serial port protocol profile: serial-connected slave Other serial port protocol profile: serial-connected slave Use the serial-connected slave profile to connect a slave device to the serial port using any IA serial port protocol not previously discussed in this guide. -
Page 16: Configure A Serial-Connected Slave: Generic Procedure
Use this procedure in the following situations: When a protocol master using one of the supported serial port protocols (Modbus ASCII, Modbus RTU, DF1 Full-Duplex, FINS, Hostlink, CompoWay/F or a protocol that meets Digi’s definition of a “user-defined” protocol) is connected to the serial port. -
Page 17: Configure A Serial-Connected Master: Other Ia Protocol
Configure the Digi One IAP using IA profiles Configure a serial-connected master: other IA protocol When the device connected to the serial port is a slave that is using a “non-supported” serialport protocol, that is, the serial port protocol is not Modbus ASCII, Modbus RTU, DF1 Full- Duplex, FINS, Hostlink, CompoWay/F, or a protocol that meets the definition of a “userdefined”... -
Page 18: Set Up Com Port Redirection
Configure the serial port for RealPort Use this topic for information on configuring the Digi One IAP serial port. 1. Access the Digi One IAP configuration from a web browser by entering IP address for the device in the browser’s URL window. - Page 19 Configure the Digi One IAP using IA profiles Set up COM port redirection 1. Go to the device support page. 2. From the OPERATING SYSTEM SPECIFIC DRIVERS: drop-down list, select your operating system. A list of drivers appears. 3. Click the link for your operating system, and save the .zip file to your hard drive.
-
Page 20: Administration Tasks
If the default log in information does not work, the user name and/or password may have been updated. Contact your system administrator. Update firmware You can upgrade the firmware for Digi One IAP from the web interface using the HTTP or TFTP protocol. Upgrade firmware from the web Interface using HTTP 1. -
Page 21: Update Post Code
5. Click Restore to reset the configuration. Reset the Digi One IAP from the command line To reset the Digi One IAP from the command line, use the revert and boot commands. For command descriptions, see Digi One and PortServer TS Family Command Reference. -
Page 22: Reset The Digi One Iap Using The Reset Button
Enable pass-through port The Digi One IAP has a second DIP switch on the top of the device for enabling the pass-through port. When the pass-through port DIP switch is enabled (ON), the DIP switch bank for EIA-232/422/485 operates for the screw terminal port only. - Page 23 Connect Pins 2, 4, 7, 9 Connect Pin 3 to 6 485 loopback for screw terminal Connect Pin 1 to 8 Connect Pin 2 to 9 Connect Pin 3 to 6 Connect Pin 4 to 7 Digi One IAP Family User Guide...
-
Page 24: Interpreting The Status Leds
Serial port activity. No serial port activity. Green RTS is on. RTS is off. Green CTS is on. CTS is off. Green DTR is on. DTR is off. Green DSR is on. DSR is off. Green DCD is on. DCD is off. Digi One IAP Family User Guide... -
Page 25: Hardware Information
5 to 90% non-condensing Mechanical Width 101 mm Height 22.5 mm Depth 120 mm CAUTION! This unit has two power inputs. For total isolation from electrical shock and energy hazard, disconnect both power inputs. Digi One IAP Family User Guide... -
Page 26: Regulatory Information
(2) this device must accept any interference received, including interference that may cause undesired operation. Modifications (FCC 15.21) Changes or modifications to this equipment not expressly approved by Digi may void the user's authority to operate this equipment. Cables (FCC 15.27) Shielded cables must be used to remain within the Class A limitations. -
Page 27: Safety Considerations And Warnings
If you require an extension cord, ensure that the ampere rating of all equipment plugged into the extension cord does not exceed the ampere rating of the cord. If the Digi One IAP is exposed to moisture or condensation, disconnect it from the power source immediately and obtain service assistance.