Related Manuals for imovr Omega EVEREST
Summary of Contents for imovr Omega EVEREST
- Page 1 Omega EVEREST 3D-Adjustable Sit/Stand Desk System INSTALLATION MANUAL VERSION 3.0...
-
Page 2: Before You Begin
BEFORE YOU BEGIN PROVIDED FOR DESK ASSEMBLY (12) 1” flat-head (4) black ⅝” hex head (8) 20mm round-head machine screws machine screws and machine screws (STEP 3) (4) silver ⅝” hex head (STEP 2) machine screws (STEP 4) (8) 5mm x 60mm (8) 5mm x 20mm machine screws machine screws... - Page 3 PROVIDED FOR KEYBOARD TRAY ASSEMBLY (8) M5 20mm pan head (7) #10 5/8” pan head machine screws Phillips screws (6) #10 1-1/4” flat head (STEP 12) (STEPS 11 & 14) Phillips screws (STEP 11) (1) Keyboard Platform Mounting Assembly (1) Keyboard Platform (1) Keyboard fence (2) Keyboard Platform Supports (2) Rubber bumpers...
- Page 4 ASSEMBLY INSTRUCTIONS FOR THIS STEP SET THE TABLE TOP CLEAR a good-sized area to lay out all components and assemble the desk. Lay the table top down on the floor, insert nut side facing up. If not on carpet, we recommend placing a soft blanket down first in order to protect the table top surface.
- Page 5 FOR THIS STEP ATTACH CROSSBARS TO LEGS ATTACH the crossbars to both sides of each motor housing using the twelve (12) 1” flat- head machine screws provided. Take care to align the holes properly so that the screws go in straight. Note: only two of the three holes need to be used.
- Page 6 FOR THIS STEP ALIGN BASE TO TABLE TOP PLACE the base down on the table top and line up the holes in the left top support arm with the Marker/pen to mark center hole recessed nuts in the table top. If your desktop is 48” wide (not provided) you can proceed to Step 6.
- Page 7 FOR THIS STEP TIGHTEN REMAINING SCREWS USE the #5 Allen key to tighten the four (4) screws that hold the top support arms to the base, and the four (4) set screws on each of the crossbars. these four (4) screws on these four (4) set screws the arms are the same on the crossbar are the...
- Page 8 FOR THIS STEP ATTACH CABLES 1. PLUG the left- and right-side drive cables into any of the three 8-pin motor sockets. 2. PLUG the hand controller into the round 7-pin socket 3. CONNECT the power supply to the power cable, after all other connections. POWER SUPPLY LEFT POWER SUPPLY RIGHT power outlet...
- Page 9 (3) small wood screws provided. SEE NEXT PAGE FOR PLACEMENT ILLUSTRATION. SCREW INTO THE DESK’S UNDERSIDE FROM THE BOTTOM OF THE HAND CONTROLLER ASSEMBLY *all omega everest desks come with an updated face plate for the hand controller...
- Page 10 Use the Pre-Drilled Holes to Mount the Digital Hand Controller Tabletops With Center Cutouts Have Pre-Drilled Holes on the Left and Right All Tabletops With Left and Right Cutouts Have Pre-Drilled Holes in the Center...
- Page 11 FOR THIS STEP ASSEMBLE KEYBOARD PLATFORM ATTACH the two foot supports to the underside of the keyboard platform using three #10 1-1/4” flat head Phillips screws and three spacers per foot support. Position each set of spacers between the foot support and the underside of the keyboard platform.
- Page 12 FOR THIS STEP ATTACH KEYBOARD PLATFORM USING eight M5 20mm pan head machine screws, attach the mounting assembly and platform to the underside of the desk. Align the tube assembly by matching the four holes on each mounting bracket to the four insert nuts on both sides of the Omega cutout.
- Page 13 FOR THIS STEP ATTACH KEYBOARD FENCE TILT the Omega keyboard platform so that you can easily access both the top and bottom of the rear end of the platform. Using three #10 5/8” pan head Phillips, attach the keyboard fence to the back of the platform so that the built-in cable guide is facing up when the keyboard platform is flat.
- Page 14 FOR THIS STEP ATTACH RUBBER BUMPERS ATTACH each rubber keyboard bumper to the keyboard platform by fitting a carriage bolt through each of the two slots cut into the platform so that the bolt’s head is flush with the underside of the platform.
- Page 15 USER INSTRUCTIONS MAKE sure there is nothing blocking the travel of the desk in the space where it will operate. After the desk is assembled and plugged into the power outlet, the controller will need to be initialized. To do so, press and hold the “Down”...
- Page 16 MANUAL RESET IF THE actual desktop position no longer corresponds to the height displayed, you can reset the lowest desktop position to the minimum height. PRESS and hold the desktop down key until the desktop has reached the lowest position (programmed desktop position). PRESS and hold the desktop down key again.
-
Page 17: Troubleshooting
The control unit has now registered the lowest elevation and is ready to use. 3. SHOULD the table still not work as intended after taking these measures, please contact the iMovR Customer Care Department for assistance. -
Page 18: Optional Accessories
OPTIONAL ACCESSORIES IN-SURFACE DUAL-AC POWER SOCKET THE 3” grommet holes provided in the table tops are ideally sized for accepting the flush-mounted power socket “nodes. ” PREVENTATIVE MAINTENANCE & CLEANING AFTER first week of use: Tighten down all screws and bolts. CLEANING the base: Clean the base frame by wiping it down with a microfiber cloth moistened with a standard household cleaning solution. -
Page 19: Warranty
WARRANTY THE OMEGA EVEREST warranty coverage includes 20 years on the steel frame, 10 years on moving parts, 5 years on table tops, and 2 years on the electronics. The following limitations apply: THIS WARRANTY only covers defects as specified herein and does not include defects or damages attributable to improper installation, misuse or normal surface weathering, or defects or damages caused by accidents or fire or other casualty or Acts of God, or any other causes or occurrences beyond the manufacturer’s control. -
Page 20: Specifications
Single and Dual-Arm LCD Monitor Stands Grommet-mounted Dual-AC Power Socket HOURS: See www.iMovr.com/hours PHONE: (888) 208-6770 or (425) 999-3550 FAX: (425) 999-3550 E-MAIL: customercare@imovr.com any brand of walking treadmill may be used with omega desks. LIVE CHAT: www.iMovR.com OMEGA EVEREST INSTALLATION MANUAL PART NO. DO-IM-OE-INST...