Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for imovr Omega Olympus
Summary of Contents for imovr Omega Olympus
- Page 1 Omega Olympus ™ Adjustable - Height Desk System INSTALLATION MANUAL...
-
Page 2: Table Of Contents
BEFORE YOU BEGIN STEP 1 Congratulations on purchasing an Omega GET READY Use these charts to make sure all the contents of your desk and Olympus™ adjustable-height desk system! keyboard tray kit are present. We designed this product to be as easy as possible to assemble, but if you have any DESK ASSEMBLY PARTS questions during the assembly process, please... - Page 3 KEBOARD TRAY ASSEMBLY PARTS DESK ASSEMBLY PARTS Part Part Picture Picture name name #10 1-1/4” M10 Set Flat head screw phillips screws Tube cap #10 5/8” Pan head phillips Machine Narrow base screws screws Wide base M5 20mm Pan head machine screws Select...
-
Page 4: Assembly Instructions
ASSEMBLY INSTRUCTIONS STEP 2 TABLE TOP BASICS The Olympus Select top is 1-1/8” and comes with pre-drilled recessed nuts on the underside. Be sure to clear your working area of any materials that might scratch or damage the top of the desk. Lay the table top on the floor upside-down on carpet or a blanket. - Page 5 ATTACH THE EXTENSION CHANNEL TO THE CROSSBAR STEP 6 The Olympus base comes in two sizes: Narrow Frame Accomodates desk sizes 42”, 47” and 59” Wide Frame Accomodates desk sizes 71” and 83” The narrow frame model comes with a standard length extension channel (Part # 8).
- Page 6 STEP 8 AFFIX THE BASE TO THE DESK TOP Now that the base is correctly aligned with the table top, join the two by using the 12 provided screws (Part # 12). It is a good idea to use a screwdriver or drill bit with a magnetic tip as it will help in the alignment of screw to recessed nut.
- Page 7 STEP 10 INSTALL UP/DOWN CONTROLLER All Olympus desk-tops have pre-drilled pilot holes for installing the hand controller on either the left or the right side of the desk. Using the 2 small pan-head wood screws (Part # 16) supplied, attach the controller to your preferred location. The controller is on a slider plate that moves to a slightly recessed and protected position.
- Page 8 STEP 12 ATTACH KEYBOARD PLATFORM USING eight M5 20mm pan head machine screws, attach the mounting assembly and platform to the underside of the desk. Align the tube assembly by matching the four holes on each mounting bracket to the four insert nuts on both sides of the Omega cutout.
- Page 9 STEP 14 ATTACH KEYBOARD FENCE TILT the Omega keyboard platform so that you can easily access both the top and bottom of the rear end of the platform. Align the three holes of the Fence with the three holes on the bottom of the platform.
- Page 10 STEP 16 USING THE OMEGA KEYBOARD PLATFORM THE OMEGA Keyboard Platform can be set to one of two height positions. By default, the bar assembly arrives set to the lower position. You can adjust the bar assembly higher by removing the two hex screws from both ends of the pivot bar, and reattaching the bar by inserting those same hex screws through the upper set of holes on the bracket.
- Page 11 Use the individual leveling pads to adjust as necessary. Plug in the power cable to a 3-prong outlet and enjoy your new Omega Olympus Desk. Enjoy a healthier, more productive workday. AFTER connecting all the cables and testing that the desk is working...
-
Page 12: Controller Instructions
CONTROLLER INSTRUCTIONS INITIALIZATION PROCEDURE The initialization procedure must be completed before the desk can be used. Step Operation Motion Press and hold p&q simultaneously Legs begin to move down at a half speed of normal operation more than 3 seconds Keep pressing q&p Legs move down to the lowest position and rebound 2-5 mm, then stop Initialization is completed... - Page 13 TOGGLE THE DISPLAY UNIT FORMAT Step Operation Motion Press and hold button S, then press and The height information will be changed between centimeters and inches hold q, for about 3 seconds Release the buttons Completed Note: In the Imperial format (inches), the minimum height variation is 0.5in. In the metric format, the minimum height variation is 1cm. VERIFY THE DISPLAY SWITCH DATA TO MATCH THE DESK HEIGHT Step Operation...
-
Page 14: Final Touches
This is a smart way to tidy up all the loose or draped cables. iMovR.com offers a basic kit and an advanced kit. Both are available at:... -
Page 15: Preventative Maintenance, Cleaning
PREVENTATIVE MAINTENANCE, CLEANING, WARNINGS AND GOOD-SENSE TIPS RE-TIGHTEN CLEANING THE DESKTOP After first week of use it’s a good idea to check and re-tighten any All desktops are manufactured with a “3D lamination” process that screws / bolts. results in an extremely durable surface, similar to what’s often used in hospital environments. -
Page 16: Warrenty
(b) within 30 days after notice of claim, is in receipt of the defective unit at its place of business, unless this requirement is waived by iMovR. The manu- facturer will arrange for retrieval of the defective product via its carrier-of-choice.
Need help?
Do you have a question about the Omega Olympus and is the answer not in the manual?
Questions and answers