Related Manuals for WilTec 51702
Summary of Contents for WilTec 51702
- Page 1 LAWN SWEEPER INSTRUCTION MANUAL 51701.51702.51703 © by WilTec Wildanger Technik GmbH Seite - 1 - http://www.WilTec.de http://www.aoyue.eu http://www.teichtip.de...
-
Page 2: Safety Rules
16. Axle lubrication needs to be added before each usage. Look for this symbol to point out important safety precautions. It means—Attention! Become alert! Your safety is involved. © by WilTec Wildanger Technik GmbH Seite - 2 - http://www.WilTec.de http://www.aoyue.eu... - Page 3 12. Lower Hopper Side Tube 5. Hitch Bracket 13. Rear Hopper Tube (2) 6. Hopper Bag 14. Upper Hopper Side Tube 7. Connecting Rod 15. Rope 8. Sweeper Housing Assembly © by WilTec Wildanger Technik GmbH Seite - 3 - http://www.WilTec.de http://www.aoyue.eu http://www.teichtip.de...
- Page 4 Clevis Pin Ø9.5x25 Nylon Lock Nut M8 Clevis Pin Ø6x37 Nylon Lock Nut M6 Clevis Pin Ø8x59.5 Hex Bolt M6x12 Hitch Pin Big Flat Washer Ø8 Plastic Plug © by WilTec Wildanger Technik GmbH Seite - 4 - http://www.WilTec.de http://www.aoyue.eu http://www.teichtip.de...
- Page 5 3. (Figure 2) Assemble the R.H Hitch Tube to the sweeper housing using M6x40 Hex Bolt and M6 Lock Nut. Do not tighten yet. Repeat for the L.H hitch tube. M6X40 HEX BOLT © by WilTec Wildanger Technik GmbH Seite - 5 - http://www.WilTec.de http://www.aoyue.eu http://www.teichtip.de...
- Page 6 Finally, tighten the two bolts fastening the hitch brackets to the hitch tubes. 7. (Figure 4 or 5) Assemble the hitch pin, spacers and the hair cotter pin to the hitch brackets. © by WilTec Wildanger Technik GmbH Seite - 6 - http://www.WilTec.de http://www.aoyue.eu...
- Page 7 9. (Figure 7) Insert a M8x20 hex bolt through the angle bracket. Assemble onto the bolt ( in order ) the spacer bushing, the height adjustment strap, a Ø8 big flat washer and a M8 hex lock nut. Tighten. © by WilTec Wildanger Technik GmbH Seite - 7 - http://www.WilTec.de...
- Page 8 Tighten the nuts securing the height adjustment handle. 11. （Figure 9） Assemble the Connecting Rod to the sweeper housing by using two sets of Hex Bolt M6x12 and Lock Nut M6. © by WilTec Wildanger Technik GmbH Seite - 8 - http://www.WilTec.de http://www.aoyue.eu...
- Page 9 (Figure 12) Turn the second rear hopper tube so that the brace holes in the middle of the tube face up. Assemble the ends of the rear hopper tube onto the ends of the lower hopper side tubes. Fasten together using plastic plugs. © by WilTec Wildanger Technik GmbH Seite - 9 - http://www.WilTec.de http://www.aoyue.eu...
- Page 10 Ø2. (Figure 15) Secure the bag corners around the lower hopper side tubes by snapping the bag flaps to the bag bottom on both sides. FLAP © by WilTec Wildanger Technik GmbH Seite - 10 - http://www.WilTec.de http://www.aoyue.eu...
- Page 11 11. (Figure 17) Feel along the stitched flap on the hopper bag to locate the lower hole in each upper hopper side tube. Place a hole through both sides of the stitched flaps in alignment with the lower hole. © by WilTec Wildanger Technik GmbH Seite - 11 - http://www.WilTec.de http://www.aoyue.eu...
- Page 12 14. (Figure 20) To assemble the hopper bag to the sweeper, slide the ends of the bag arm tubes into the ends of the sweeper’s hitch tubes and secure with two Ø6X37 clevis pins and hair cotter pins Ø2. © by WilTec Wildanger Technik GmbH Seite - 12 - http://www.WilTec.de...
- Page 13 DRAWING © by WilTec Wildanger Technik GmbH Seite - 13 - http://www.WilTec.de http://www.aoyue.eu http://www.teichtip.de...
-
Page 14: Parts List
Cotter Bearing Hitch Tube (L.H.) R Pin Ø3 Big Flat Washer Ø10 R Pin Ø2 Hex Bolt M10x85 Big Flat Washer Nylon Lock Nut M5 Hex Bolt M8×20 © by WilTec Wildanger Technik GmbH Seite - 14 - http://www.WilTec.de http://www.aoyue.eu http://www.teichtip.de...