Table of Contents
Advertisement
Installation Job Aid (English) for Avaya
Ethernet Routing Switch 4000 Series
(NN47205-303, ver 01.01)
How to get help
To access the complete range of services and support that Avaya provides, go to
www.avaya.com.
You can also go to
• technical documentation
• product training
• technical support
If you purchased a service contract for your Avaya product from a distributor or authorized
reseller and you need assistance, contact the technical support staff for that distributor or
reseller.
Notices
Notice paragraphs alert you about issues that require your attention. The following paragraphs
describe the types of notices used in this guide.
Note:
Notes provide tips and useful information regarding the installation and operation of Avaya
products.
www.avaya.com/support
to access the following pages:
November 2013
1
Advertisement
Table of Contents
Related Manuals for Avaya ERS 4000 Series
Summary of Contents for Avaya ERS 4000 Series
- Page 1 • technical documentation • product training • technical support If you purchased a service contract for your Avaya product from a distributor or authorized reseller and you need assistance, contact the technical support staff for that distributor or reseller. Notices Notice paragraphs alert you about issues that require your attention.
-
Page 2: Safety Messages
Safety messages Electrostatic alert: ESD notices provide information about how to avoid discharge of static electricity and subsequent damage to Avaya products. Caution: Caution notices provide information about how to avoid possible service disruption or damage to Avaya products. Warning: Warning notices provide information about how to avoid personal injury when working with Avaya products. - Page 3 Safety messages Caution: When mounting this device in a rack, do not stack units directly on top of one another in the rack. Each unit must be secured to the rack with appropriate mounting brackets. Mounting brackets are not designed to support multiple units. Voltage: Use only power cords that have a grounding path.
-
Page 4: Installation Preparation
• Adequate space at the front and rear of the switch for access to cables If you are installing a single Avaya Ethernet Routing Switch on a table or shelf, ensure the surface can support at least 15 to 20 pounds (7 to 9 kilograms). - Page 5 Installation preparation Attach a bracket to each side of the switch. Slide the switch into the rack. Insert and tighten the rack mount screws. November 2013...
-
Page 6: Installing The Switch On A Table Or Shelf
Installation preparation Note: The ERS 4000 Series mounting hardware is specific for each switch model. Do not mix screws or brackets between different ERS 4000 Series switches. Installing the switch on a table or shelf You can install a single Avaya Ethernet Routing Switch on any flat surface that can safely support the weight of the switch and attached cables (15 to 20 pounds or 7 to 9 kilograms). - Page 7 Installation preparation Attach the rubber feet at the marked locations. November 2013...
-
Page 8: Ac Power Specifications
Installation preparation Set the switch on a table or shelf. Note: Allow at least 2 inches (5.1 cm) on each side for proper ventilation and at least 5 inches (12.7 cm) at the back for power cord clearance. AC power specifications The following table describes the AC power specifications for the Ethernet Routing Switch 4000 Series. - Page 9 Installation preparation Model Input Input Input Input Power Thermal current current voltage voltage consump- rating (amps (amps (rms, VAC (rms, VAC tion (watts (Btu/h maximum maximum at 50-60 at 50-60 max) maximum) at 100-120 at 200-240 VAC) VAC) 100-120 200-240 4550T- 100-120 200-240...
-
Page 10: Connecting Ac Power
Installation preparation Connecting AC power Required cable: AC power cord that meets the requirements of your local electrical code. Refer to the following table for plug specifications. Table 1: International power cord specifications Country and plug description Specifications Typical plug Continental Europe 220 or 230 VAC 50 Hz... -
Page 11: Installing The Power Supply
Installing the power supply You must install at least one power supply before using the switch. Some ERS 4000 Series models can support an optional second power supply for redundancy and load sharing. To install the power supplies into your switch, perform the following procedure.