Lunos e2 Installation Manual
Decentralised ventilation system with heat recovery
Hide thumbs
Also See for e2:
- Installation manual (18 pages) ,
- Mounting instructions (8 pages) ,
- Operation manual (5 pages)
Advertisement
Quick Links
I
DE
Einbauanleitung
Dezentrales Lüftungssystem
mit Wärmerückgewinnung
Typen e², e²kurz und e²neo
- Bitte an den Nutzer weiterleiten -
II
EN
Installation Manual
Decentralised Ventilation System
with Heat Recovery
Type e², e²short and e²neo
- Please pass on to user -
11
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Lunos e2
Summary of Contents for Lunos e2
- Page 1 Einbauanleitung Dezentrales Lüftungssystem mit Wärmerückgewinnung Typen e², e²kurz und e²neo - Bitte an den Nutzer weiterleiten - Installation Manual Decentralised Ventilation System with Heat Recovery Type e², e²short and e²neo - Please pass on to user -...
- Page 2 Assembly: Electric installation and Electric connection Assembly: Heat recovery unit and Inner screen Assembly: Sound insulation set Replacement of ALD-R 160 by e², Note on LUNOS Outer covers Filter replacement, Cleaning, Additional parts and Replacement parts About this manual ...
- Page 3 Dimension diagrams (all dimensions in mm) 300 - 700 DA 160 Heat exchanger 200* –300 Dimensions in mm Heat exchanger ring e²short : *Shorten EPP ring if necessary Installation position Decentralised ventilation devices with heat recovery of the type e² only function in pairs in bidirectional operation.
-
Page 4: Shipping Units
Operating range Temperature range: -15°C to +40°C Usable with relative humidity levels of up to 65% in the interior area. During heating periods low levels of condensate formation may occur. When usage limits are exceeded, switch off the device and close the inner screen. - Page 5 Assembly: Assembly pipe and outer grille ① Make the wall openings for the as- sembly pipes (e.g. by coring, core bit Ø 162 mm). If necessary shorten the pipe to the required installation length (e²: min. 300 mm; e²short: min. 200 mm). Plaster protection cap Take care that the pipe overlaps on Indoors...
-
Page 6: Safety Instructions
Electric connection only by a specialist. Additional installations and electrical components in this ventilation system are not allowed. ➃ The system can be controlled via Device 1 Device 2 several controls of LUNOS. Supply/Exhaust Exhaust/Supply Follow the relevant installation instructions. Connector box Select the position of the switch. - Page 7 Assembly: Heat recovery unit and Inner screen ⑥ Motor Remove plaster protection cap inside, insert heat exchanger unit into the assembly pipe, ensure there is a 22 mm spacing. Motor is on the inside. Using the loop on the inside of the heat exchanger unit the said unit may be pulled out for correction purposes.
- Page 8 5 onward. Note on LUNOS outer covers The full-plastic outer covers supplied by LUNOS provide high resistance to driving rain and meet the reqirements of Stress Group III according to DIN 4108-3 (2014-11). Metallic or metal-coated covers can be used in Stress Group I in accordance with DIN 4108-3 (2014-11).
- Page 9 W1 for 3 seconds. For the functionality of the filter change indicator in connection with the TAC or the LUNOS-KNX Control please see the LED iIluminates beneath the switch corresponding instructions. Please note below information on the filter changes you have carried out:...
- Page 10 The product’s installation shall not conflict with any requirement in the National Electrical Code, ANSI/NFPA 70-1999. Additional installations and electrical components in this ventilation system are prohibited! LUNOS Germany LUNOS Lüftungstechnik GmbH Phone +49 30 362 001-0 für Raumluftsysteme +49 30 362 001-89 Wilhelmstr.
Need help?
Do you have a question about the e2 and is the answer not in the manual?
Questions and answers