Page 1
Igloohome Smart Padlock Model: IGP1 1. Dimensions and weight Body Thickness 32mm Body Length 70mm Body Width 55mm Shackle Thickness Vertical Clearance 26mm Horizontal Clearance 24mm Estimated product weight 450 g 2. Overall Design ...
Page 2
3. Packaging Content T27 TORX screwdriver CR2 battery Quick Start Guide (Link to e‐manual) 4. Material Shackle and Locking Mechanism: Hardened Steel Casing: Zinc Alloy 9V Battery cover – Rubber Buttons: Metal 5. Environmental and Reliability Operating Temperature: ‐25 to 55 Degree Celsius Storage Temperature: ‐40 to 70 Degree Celsius Operating Humidity: 0 to 95% Relative Humidity (Rh) Dust and Water Resistance: Product must pass IP66 certification 6. Battery Life Battery used: 1 x CR2 Up to 1 year 7. Secured Battery Cover Battery cover can only be removed by using a Torx Security screwdriver (Recommended: T27) only when shackle is unlocked. ...
Page 3
OPEN CLOSED 8. Buttons and LED 12 Buttons (4 x 3) Status Indicator: Red, Green, Blue Keypad LED 9. Audio and LED indications Digit 1 short Beep Unlock icon 1 short Beep Clear icon 2 short beeps Bluetooth connection Status indicator flashes BLUE Successfully unlocked A‐B‐C‐D beeps after unlocked and flash Green LED 2 times Successfully locked 1 long beep after locked and Green LED for 2 seconds Incorrect PIN 4 short beeps and flash red 2 times Reached max no of digits (16) 4 short beeps and flash red 2 times ...
Page 4
Security Mode deactivated 2 long beeps Low Battery Alert D‐C‐B beeps when keypad woken up and Breathing Red LED Relock Reminder Alert Red flash twice and quick beep twice repeatedly Factory Reset D‐C‐B‐A beeps Power Up 2 slow beeps then 2 quick beeps 10. Masking PIN Maximum = 16 digits including masking pin Product will allow up to 8 masking pins before the actual PIN code (8 digits). Product will allow up to 9 masking pins before the actual PIN code (7 digits). Product will allow up to 10 masking pins before the actual PIN code (6 digits). Product will allow up to 11 masking pins before the actual PIN code (5 digits). Product will allow up to 12 masking pins before the actual PIN code (4 digits). 11. Emergency Jumpstart If internal batteries are fully drained or low Battery, user can use a 9V Battery to stay in contact to 2 conical contact pins (about 12mm apart) to jumpstart the product. When that 9V battery contacts with the 9V contact, there will be one single beep and keypad lights up for user to use any entry methods to ...
Page 5
User can change configuration via accessing a retaining pin after removing battery cover When in retained shackle configuration, User is able to pull the shackle up but shackle still remain in body. User is unable to remove the shackle as internal mechanism is holding the shackle. When Padlock is unlocked, it should not be too hard to open the padlock. When in removable shackle configuration, User is able to pull the whole shackle out as internal mechanism is not holding the shackle. When in removable shackle configuration, user is able to pull the shackle up to open the padlock and with a higher force to remove the shackle. When Padlock is unlocked, it should not be too hard to open the padlock. When Padlock is open, it should not be hard to remove the shackle. 13. Manual Relock Hold on # for one second to manual relock (backup) 14. Auto Relock If Auto relock is ON, the lock will relock after the shackle is closed. If the lock is unlocked and shackle is kept closed, the lock will relock after 30 seconds (fixed). 15.
Page 6
Unpaired product can be unlocked with Factory Pin code of 1234567890 (to test all buttons) followed by the Unlock Icon. Hard Reset can be performed only when padlock is unlocked state 17. Connectivity Bluetooth 4.2 – Bluetooth Low Energy (BLE) 18. Volume Control Volume can be changed via Bluetooth 10 levels 19. Keypad LED Toggle Keypad LED can be switched on or off via Bluetooth By default, it is switched on 20. Keypad Security Lockout Keypad Security Lockout will be triggered if Incorrect pins are attempted for a number of consecutive times. “Keypad Security Lockout” can only be activated when the lock is locked User is able to Enable and disable Keypad Security Lockout via BT User is able to configure 1 to 10 incorrect pins (default = 5) When “Keypad Security Lockout” is triggered 1st time: There will be siren for 30 seconds Keypad will not accept any pin codes for 1 minute When “Keypad Security Lockout ” is consecutively triggered 2nd time: ...
Page 7
21. Relock Reminder Alert Relock Reminder Alert will be triggered if the lock is not locked within a period of time (user‐defined) User is able to Enable and disable Relock Reminder Alert via BT User is able to configure 10 seconds to 10 minutes 22. Access Requirements Master BT Key Guest BT Key Master PIN Permanent PIN Duration PIN One Time PIN Recurring PIN o Weekly PIN o Monthly PIN o Weekday PIN o Weekend PIN Algo generated (7 to 9 digits) BT generated (4 to 6 digits) ...
Page 8
FCC Warning Statement Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ‐‐ Reorient or relocate the receiving antenna. ‐‐ Increase the separation between the equipment and receiver. ‐‐ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ‐‐ Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.