Hans Grohe Trio 15984180 Assembly Instructions Manual
Hans Grohe Trio 15984180 Assembly Instructions Manual

Hans Grohe Trio 15984180 Assembly Instructions Manual

Advertisement

DE Montageanleitung
EN assembly instructions
2
3
Trio
15984180

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Trio 15984180 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Hans Grohe Trio 15984180

  • Page 1 DE Montageanleitung EN assembly instructions Trio 15984180...
  • Page 2 Deutsch Sicherheitshinweise Montage (siehe Seite 5) 6 Bei der Montage müssen zur Vermeidung von 1. Eingebaute und geprüfte Trio einputzen, bzw. bei Quetsch- und Schnittverletzungen Handschuhe Vorwandinstallation mit Paneel verkleiden. getragen werden. Nach Austrocknen der verputzten Wandoberfläche, 6 Große Druckunterschiede zwischen den Kalt- und die Nahtstelle zwischen Wand und Abdichthülse des Unterputzventils mit Silikon (essigsäurefrei!) Warmwasseranschlüssen müssen ausgeglichen werden. ausspritzen. Montagehinweise 2. PCI-Lastogum oder einen vergleichbaren Dichtstoff nach Herstellerangaben auf die Wand auftragen. • Die Armatur muss nach den gültigen Normen montiert, 3. Dichtmanschette über die Abdichthülse stülpen und gespült und geprüft werden. in den Kleber und Silikon eindrücken. • Die in den Ländern jeweils gültigen Achtung! Die Dichtmanschette darf nicht Installationsrichtlinien sind einzuhalten. heiß verklebt werden. • Vor der Montage muss das Produkt auf Falls die Trio Stop Ab- / Umstellung heißverklebt Transportschäden untersucht werden. Nach werden soll, muß darauf geachtet werden, das diese dem Einbau werden keine Transport- oder...
  • Page 3: Installation Instructions

    English Safety Notes Assembly (see page 5) 6 Gloves should be worn during installation to prevent 1. Plaster in the installed Trio, in case of pre-wall crushing and cutting injuries. installation cover the Trio with a panel. 6 The hot and cold supplies must be of equal After the plastered wall surface is dry, seal the gap pressures. between wall and plastic sleeve of the flush valve with silicone (free from acetic acid!). Installation Instructions 2. Apply PCI-Lastogum or similar sealing compound • The fitting must be installed, flushed and tested after on the wall in accordance with manufacturers the valid norms. indications. • The plumbing codes applicable in the respective 3. Put gasket over the plastic sleeve of the Quattro countries must be oberserved. four-way-diverter. • Prior to installation, inspect the product for transport Important! The gasket is not suitable for damages. After it has been installed, no transport or hot glue. surface damage will be honoured.
  • Page 4 Thermostat mit Absperrventil thermostatic mixer with shut-off valve Absperrventil shut-off valve Thermostat thermostatic mixer...
  • Page 5 Schallentkopplung / noise reduction...
  • Page 7 98798000 39x2,5 97550000 96493000 95509000 SW 27 mm 96370000 (25 mm)
  • Page 8 Trio E Trio S Trio PuraVida 15931000 15932000 15937000 / 15937400 Trio Classic Trio Metris 15934000 31634000 Hansgrohe · Auestraße 5 - 9 · D-77761 Schiltach · Telefon +49 (0) 78 36/51-1282 · Telefax +49 (0) 7836/511440 E-Mail: info@hansgrohe.com · Internet: www.hansgrohe.com...

Table of Contents