Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Axis 2N Lift1
Summary of Contents for Axis 2N Lift1
- Page 1 ® Lift1 Comunicator for Lifts Brief Manual Issue 2, Version 1.3 www.2n.cz...
-
Page 2: Operation
Sortiment Part No. Description 919640xx Basic model for mounting below the panel 919618xx Model with the front panel 919630xx Model in metallic case Extending modules Part No. Description Universal switch – remotely controlled switch by 913648E DTMF, one switch or lift blocking module can be used. Lift blocking module –... - Page 3 Play the user message for lift identification, if stored in Lift1. Extend the call by 30 seconds. Can be used repeatedly. Terminate the call. Identification sending for LiftManager Switch operating keyword for switch must start with this numbers. až Before you start Installation Conditions •...
- Page 4 Mounting Drawing for basic model of Lift1 Mounting holes, four M4 spot- welded screws from shaft side recomended Perforated speaker area, in the cabin wall must be the perforation for good sound quality, the perforated area must not exceed the Lift1 panel Two optional LED holes, when these LEDs are used, model with lightguides is suggested for better...
-
Page 5: Electrical Installation
Electrical Installation Terminals description Connector / Name Description ALARM1 DC = voltage 12–24 V DC, any polarity, activation control *) by signal or no signal state possible Terminal Alarm call activation normally open or normally closed contact control contact ALARM2 contact control Alarm 2 call or end of Normally open contact only... - Page 6 signalization till rescue is done, line failure signaling). See the wiring diagram for external indicators below. Plugs and connectors on the bottom side of Lift1 Connectors for external LED supplied from Lift1 and connectors for external microphone and speaker can be used for connecting of these parts on cables, allowing the user to place it according the construction of the lift cabin.
-
Page 7: Telephone Line Connection
loop. When the whole lift cabin should be covered with signal, amplifier for induction loop must be used, for more information contact producer. There is possible to equip Lift1 with universal switch remotely DTMF-controlled or by Lift blocking module to block the lift function during telephone line failure. The Amplifier module is accessory equipment for increasing volume in noisy environment, it needs external supplying and it is electrically separated from the power line. -
Page 8: Access To Programming Mode
Access to Programming Mode You can only enter the programming mode during an incoming call (from a phone to Lift1). Enter the access password: service password (remember to enter an asterisk in front of and behind the password!) If the password is correct and programming is enabled (jumper), Lift1 announces: „You have entered the programming mode“... - Page 9 Lift1 – Brief Programming Form Parameter number Range of Default Notes, explanations Your and name values value value 011 – ALARM button up to 16 empty Enter and 'p' for a 3-second memory 1 digits pause while programming via the 2N ®...
- Page 10 4 = send identification by DTMF 5 = message as specified in parameter 977 (after confirmation according to parameter 976) 6 = combine options 5 + 2 7 = confirmation tone (after confirmation only) 876 – End-of call 0–9 0,3,5,7 = message language 1 = English (or other main language selection...
- Page 11 3 = End the rescue process by Alarm 2 or the rescue password 4 = Special customer modification 974 – Lift 16 digits empty Numerical lift identification identification 981 – Check call 0–6 Setting options for parameter 981: 0 = disabled 1 = enabled, first call in 3 minutes and then as set in parameter 983 2 = enabled, first call in 2 hours and...
-
Page 12: Technical Parameters
Technical parameters Electrical Parameters Parameter Value Condition Minimum line current 15 mA off-hook Minimum line voltage 22 V on-hook I = 25 mA < 8 V Off-hook DC voltage drop < 16 V I = 50 mA On-hook resistance >1 MΩ U = 25..100 V 220 Ω...