Download
Share
Print this page
Dynojet POWER COMMANDER V Installation Instructions
  1. Manuals
  2. Brands
  3. Dynojet Manuals
  4. Motorcycle Accessories
  5. Power commander V
  6. Installation instructions

Dynojet POWER COMMANDER V Installation Instructions

Ducati multistrada 1100 2007-2009
Hide thumbs Also See for POWER COMMANDER V:
1
2
3
4

Advertisement

Quick Links

Download this manual
2007-2009 Ducati Multistrada 1100
I n s t a l l a t i o n I n s t r u c t i o n s
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
I14-013
www.powercommander.com
2191 Mendenhall Drive North Las Vegas, NV 89081 (800) 992-4993 www.powercommander.com
PARTS LIST
1
Power Commander
1
USB Cable
1
Installation Guide
2
Power Commander Decals
2
Dynojet Decals
2
Velcro strips
1
Alcohol swab
1
Zip tie
1
Posi-tap
THE IGNITION MUST BE TURNED
OFF BEFORE INSTALLATION!
YOU CAN ALSO DOWNLOAD THE
POWER COMMANDER SOFTWARE AND
LATEST MAPS FROM OUR WEB SITE AT:
www.powercommander.com
2007-2009 Ducati Multistrada 1100 - PCV - 1

Advertisement

loading
Need help?

Need help?

Do you have a question about the POWER COMMANDER V and is the answer not in the manual?

Questions and answers

Related Manuals for Dynojet POWER COMMANDER V

Summary of Contents for Dynojet POWER COMMANDER V

  • Page 1 PARTS LIST Power Commander USB Cable Installation Guide Power Commander Decals 2007-2009 Ducati Multistrada 1100 Dynojet Decals I n s t a l l a t i o n I n s t r u c t i o n s Velcro strips Alcohol swab Zip tie Posi-tap THE IGNITION MUST BE TURNED...
  • Page 2 POWER COMMANDER V INPUT ACCESSORY GUIDE ACCESSORY INPUTS Map - (Input 1 or 2) The PCV has the ability to hold 2 different base maps. You can switch on the fly between these two base maps when you hook up a switch to the MAP inputs. You can USB CONNECTION use any open/close type switch. The polarity of the wires is not important. When using the Autotune kit one position will hold a base map and the other position will let you activate the learning mode. When the switch is “CLOSED” Autotune will be activated. (Set to Switch Input #1 by default.) Shifter- (Input 1 or 2) These inputs are for use with the Dynojet quickshifter. Insert the wires from the CRANK Dynojet quickshifter into the SHIFTER inputs. ANALOG The polarity of the wires is not important. (Set to Switch Input #2 by default.) SPEED EXPANSION PORTS 1 & 2 INPUT 2 (Grnd)
  • Page 3 FIG.A Remove left and right side panels. Secure the PCV module to the battery as shown in Figure A using the supplied Velcro. Make sure to clean both surfaces with the supplied alcohol swab before attaching the Velcro. Secure the PCV ground wire with the small ring lug to the negative (-) terminal of the bike’s battery (Fig. A). FIG.B Locate the Throttle Position Sensor on the left side of the throttle body (Fig. B) Unplug the stock connector from the bike’s TPS to gain access to the wiring harness. FIG.C Using the supplied Posi-tap, attach the single unterminated GREY wire of the PCV to the stock ORANGE wire of the bike’s TPS wiring harness (Fig. C). This is pin position C on the stock TPS connector. The wire tap shown in Figure C is not a Posi-tap. This is an older crimp-on style wire tap. After attaching the GREY wire, plug the stock TPS connector back onto the TPS.
  • Page 4 FIG.D Route the PCV wiring harness up to throttle bodies. It is possible to install the PCV without removing the fuel tank and the airbox, although removing them may aid in the install. Unplug the stock wiring harness from the rear fuel injector (Fig. D). FIG.E 10 Plug the pair of PCV leads with YELLOW colored wires in-line of the stock wiring harness and the rear fuel injector (Fig. E). 11 Route the PCV harness under the throttle bodies to the right side of the bike. 12 Repeat steps 9 & 10 for the front fuel injector using the pair of PCV leads with the ORANGE colored wires. 13 Reinstall the left and right side panels. I14-013 www.powercommander.com 2007-2009 Ducati Multistrada 1100 - PCV - 4...