Page 2
The lift is to be used indoors for raising unoccupied motor vehicles ONLY! ONLY lift vehicles which have an individual axle weight that does not exceed one-half the lift capacity. See load capacity table below. MODEL LOAD CAPACITY SM40 4000kg aR40 4000kg SM55 5500kg aR55...
Lift Controls Turning Disconnect to the right provides electricity to the motor. Pushing button starts the motor and raises the runways. Pushing button lowers to locks. Pushing button raises lift, retracts locks and lowers runways to 200mm from floor. 5. Pushing button lowers lift from 200mm until runways are lowered to the floor. 6.
OpeRaTINg INSTRuCTIONS Surface Mounted Wheel engaging Lifts To avoid personal injury and/or property damage, permit only trained personnel to WARNING operate lift. after reviewing these instructions, get familiar with lift controls by running the lift through a few cycles before loading vehicle on lift. 1.
ReSIDuaL RISKS • Assure cargo does not cause either individual axle weight to exceed two thirds lift capacity.
Page 6
• Replace all decals on the lift if unable to read or missing. Reorder labels from Rotary Lift. Replace if bent NOTe: LIFT SHOuLD RaISe LeVeL. IF LIFT IS NOT RaISINg LeVeL, CHeCK CaBLeS FOR STReTCH. CaBLeS MaY NeeD aDJuSTMeNT (BY auTHORIZeD peRSONNeL).
TROuBLe SHOOTINg (for OpeRaTORS) Remedy Cause Trouble 1. Replace blown fuse or reset circuit breaker. Motor does not run. Blown fuse or circuit breaker. 2. Contact service representative for further assistance. 1. Fill tank with Dexron III ATF or equivalent. Motor runs but will not raise lift.
Page 8
RepaIR MaINTeNaNCe (MaINTeNaNCe auTHORIZeD BY QuaLIFIeD SeRVICe RepReSeNTaTIVe ONLY) Lockout any energy sources before beginning • Cable adjustment should be checked by a Rotary • any repairs. Authorized Installer after the first 50 loaded lift cycles and after 300 loaded lift cycles.
Page 9
TROuBLe SHOOTINg (FOR auTHORIZeD MaINTeNaNCe peRSONNeL) Cause Trouble Remedy Motor does not run. 1. Incorrect voltage to motor. 1. Supply correct voltage to motor. 2. Bad wiring connections. 2. Repair and insulate all connections. 3. Motor up switch fault. 3. Check switch. 4.
Page 10
Name und Anschrift des Herstellers Name und Anschrift seines in der EU Name and address of the manufacturer: niedergelassenen Bevollmächtigten his authorised representative in EU Rotary Lift BlitzRotary GmbH 2700 Lanier Drive Hüfinger Str.55 Madison, IN, 47250 USA 78199 Bräunlingen, Germany Diese Erklärung bezieht sich nur auf die Maschine in dem Zustand, in dem sie in Verkehr gebracht wurde;...
Page 11
EC –Declaration of conformity for EC – Machine Guide Lines 98 / 37 / EC, Appendix II A for Machine Types listed in Appendix IV Manufacturer: Rotary Lift/ Dover Corporation Address: 2700 Lanier Drive Madison (IN), 47250 USA Representative: BlitzRotary GmbH/ Dover Corporation Address: Hüfinger Straße 55...
Page 12
Replacement Parts: See installers package for parts breakdown sheet. Order Genuine Rotary replacement parts from your nearest Autho- rized Parts Distributor. Maintenance Assistance: Contact your local Rotary distributor. Should further assistance be required, contact Rotary Lift, at one of the phone numbers listed below.
Need help?
Do you have a question about the SM40 and is the answer not in the manual?
Questions and answers