Subscribe to Our Youtube Channel
Related Manuals for INOXPA CPG Series
Summary of Contents for INOXPA CPG Series
- Page 1 INSTALLATION, SERVICE AND MAINTENANCE INSTRUCTIONS CPG AGITATOR FOR WINE c/Telers, 54 Aptdo. 174 E-17820 Banyoles Girona (Spain) Tel. : (34) 972 - 57 52 00 Fax. : (34) 972 - 57 55 02 MICPG-01_EN ED. 15.02/08...
- Page 2 EC DECLARATION OF CONFORMITY (In accordance with Directive 98/37/EC, annex II, part A) INOXPA, S.A. We, the manufacturer: c/ Telers, 54 17820 Banyoles (Girona) - Spain Hereby declare that the products 2013 WINERY AGITATOR Year of Name Type Manufacture are in conformity with the provisions of the Council Directives:...
-
Page 3: Safety
Commitment to safety at the workplace. Protective goggles requirement. 1.4. GENERAL SAFETY INSTRUCTIONS Read this instruction manual carefully before installing and starting the agitator. Contact INOXPA in case of doubt. 1.4.1. During installation Technical Specifications of Chapter 8 should always be observed. - Page 4 • our equipment has been changed without prior written authorization; • the parts or lubricants used are not original INOXPA parts and products; • the materials were used incorrectly or negligently, or not in accordance with these instructions and their intended use;...
-
Page 5: Table Of Contents
2. Table of Contents Safety 1.1. Instructions manual......................3 1.2. Start-up instructions ......................3 1.3. Safety..........................3 1.4. General safety instructions ....................3 Table of contents General information 3.1. Description........................6 3.2. Range of application ......................6 Installation 4.1. Receiving the agitator ...................... 7 4.2. -
Page 6: General Information
Each agitator has performance limits. The agitator was selected for a given set of agitation conditions when the order was placed. INOXPA shall not be liable for any damage resulting from the incompleteness of the information provided by the purchaser (nature of the fluid, viscosity, RPM, etc.). -
Page 7: Installation
4. Installation 4.1. RECEIVING THE AGITATOR INOXPA cannot be held responsible for the damage sustained by the equipment during transport or unpacking. Visually check that the packaging is not damaged. The agitator will be accompanied by the following documents: • Dispatch notes. -
Page 8: Location
4.3. LOCATION Once the agitator location has been determined, it must be fixed to the tank using the nut found on the discharge pipe and firmly tightening it with the appropriate spanner. Take into account that when fitting the agitator, to prevent any deformation the agitation shaft must not be struck or forced. Install the agitator so as to allow sufficient ventilation. - Page 9 • The agitator is supplied with a connection ready for operation at 400 V (left photo). If the client has a 230 V, it should change the connection as indicated in the photo on the right. 380 – 480V 220-280V ED.15.02/08 4.Installation...
-
Page 10: Start-Up
Before starting the agitator, carefully read the instructions provided in Chapter 4. Installation. 5.1. START-UP Read Chapter 8 Technical Specification carefully. INOXPA cannot be held responsible for the incorrect use of the equipment. NEVER touch the agitator when working with high-temperature liquids. 5.1.1. Checks before starting up the agitator Check that the agitator shaft is aligned and that it slides smoothly through the hollow shaft. -
Page 11: Operating Problems
The following table provides solutions to problems that might arise during agitator operation. The agitator is assumed to have been properly installed and correctly selected for the application. Please contact INOXPA if technical assistance is required. Operating Problems Probable causes Motor overload 1, 2. -
Page 12: Maintenance
7. Maintenance 7.1. GENERAL INFORMATION Like any other machine, this agitator requires maintenance. The instructions contained in this manual cover the identification and replacement of spare parts. The instructions have been prepared for maintenance personnel and for those responsible for the supply of spare parts. -
Page 13: Disassembly / Assembly Of The Agitator
7.4. DISASSEMBLY / ASSEMBLY OF THE AGITATOR. Disassembly Remove the agitator through the valve to which it is fixed by means of the nut (45). Remove the agitator element (02, 02A) by unthreading it from the agitator shaft (05). Remove the shaft (05) behind the motor (93) by sliding it off its hollow shaft. First turn the pin (56A) properly in conjunction with the shaft turner (05A) at the end of the shaft. -
Page 14: Technical Specifications
8. Technical Specifications 8.1. TECHNICAL SPECIFICATIONS Maximum viscosity ..............100 mPa.s. Maximum pressure ..............2 bar Maximum temperature ............+80ºC +176 ºF Noise level ................60-80 dB(A) Anchor connection DIN 11851 (nut) Use special protection when the noise level in the operation area exceeds 85 dB(A). Materials Parts in contact with fluid........ -
Page 15: Cpg Agitator Dimensions
8.3. CPG AGITATOR DIMENSIONS φd φH Agitator type CPG-211A 50 / 2” CPG-211B 50 / 2” CPG-330 65 / 3” 1175 1145 ED.15.02/08 8.Technical Specifications... -
Page 16: Cpg-211A / B Agitator Exploded View
8.4. CPG-211A / B AGITATOR EXPLODED VIEW 8.Technical Specifications MICPG-01_EN... -
Page 17: Cpg-211A / B Parts List
8.5. CPG-211A / B PARTS LIST Position Description Quantity Material Discharge pipe with drainage port AISI 304 Blade AISI 304 Blade holder AISI 304 Agitator shaft AISI 304 Shaft turner AISI 304 Mechanical seal Seal cover AISI 304 Motor hood AISI 304 Stop ring AISI 304... -
Page 18: Cpg-330 Agitator - Exploded View
8.6. CPG-330 AGITATOR - EXPLODED VIEW 8.Technical Specifications MICPG-01_EN... -
Page 19: Cpg-330 Parts List
8.7. CPG-330 PARTS LIST Position Description Quantity Material Discharge pipe with drainage port AISI 304 Blade AISI 304 Blade holder AISI 304 Agitator shaft AISI 304 Shaft turner AISI 304 Mechanical seal Seal cover AISI 304 Motor hood AISI 304 Stop ring AISI 304 Centring pipe... - Page 20 Мешалки для виноделия — Боковая мешалка CPG http://k-tep.com.ua/ k-tep@ukr.net +38 044 2091823 Office +38 066 9076563 МТС Kиевстар +38 098 3676414 Skype: k-teppumps Замечания Условия поставки: DDP склад г. Киев Заметки Время поставки рассчитано согласно дате предложения и изменяется в зависимости от даты подтверждения...
Need help?
Do you have a question about the CPG Series and is the answer not in the manual?
Questions and answers