Subscribe to Our Youtube Channel
Related Manuals for INOXPA BCI Series
Summary of Contents for INOXPA BCI Series
- Page 1 INSTALLATION, SERVICE AND MAINTENANCE INSTRUCTIONS VERTICAL AGITATOR Original Manual 20.005.30.01EN (0) 2019/02...
- Page 2 Electromagnetic Compatibility Directive 2014/30/EU Applicable harmonized standards: UNE-EN ISO 12100:2012 UNE-EN 14120:2016 The technical file has been prepared by the signer of this document in INOXPA. David Reyero Brunet Technical Office Manager Banyoles, 7th February, 2019 The serial number may be preceded by a slash and by one or two alphanumeric characters...
-
Page 3: Table Of Contents
8.6. Disassembly and assemby of the agitator ....................16 9. Technical Specifications 9.1. Materials ..............................17 9.2. Other features ............................. 17 9.3. Weights ............................... 17 9.4. Dimensions ..............................18 9.5. BCI Agitator’s exploded drawing and parts list ................... 19 INOXPA S.A.U. 20.005.30.01EN · (0) 2019/02... -
Page 4: Generalities
risk to the environment due to the type of substances released. 2.3. WARRANTY Any warranty will be void immediately and lawfully and, additionally, INOXPA will be compensated for any civil liability claims submitted by third parties, in the following cases: ... -
Page 5: Safety
Electric hazard Important instruction to prevent damage to the equipment and its functions ATTENTION 3.2. GENERAL SAFETY INSTRUCTIONS Read the instruction manual carefully before installing and starting the agitator. Contact INOXPA in case of doubt. 3.2.1. During the installation Technical Specifications chapter 9 should always be observed. - Page 6 The maximum operating conditions of the agitator should not be exceeded. Nor should the operating parameters for which the agitator was initially designed be modified without written authorisations from INOXPA. Do not leave loose parts on the floor. Do not disassemble the agitator until the switchboard has been disconnected. Remove the fuses and disconnect the power cable supplying the motor.
-
Page 7: General Information
4. General Information 4.1. DESCRIPTION The agitators of BCI series are direct motor-driven agitators with a stainless steel base. In spite of being very compact, these agitators have a bearing suport that is completely independent of the motor. The half shaft is guided by two bearings that support the axial and radial forces transmitted by the agitation elements. -
Page 8: Installation
When receiving the agitator, check the packaging and its content to ensure that it matches the delivery note. INOXPA packs the agitators in their fully assembled form or disassembled on a case-by-case basis. Ensure that the agitator has not been damaged in any way. If it is not in good condition and/or any parts are missing, the carrier must submit a report as soon as possible. -
Page 9: Transport And Storage
In this position, the shaft will not become deformed but it must not be subject to any type of load. INOXPA S.A.U. 20.005.30.01EN · (0) 2019/02... -
Page 10: Location
The motor must be provided with devices for protection against power overload and short-circuits. The agitator cannot be used in areas where there is a risk of fire or explosion when this has not been specified in the order. INOXPA S.A.U. 20.005.30.01EN · (0) 2019/02... -
Page 11: Assembly
Force should never be applied to the end of the agitator shaft, as it can easily suffer permanent damage. ATTENTION Check the alignment of the agitator shaft with the half shaft once its assembly is completed. INOXPA S.A.U. 20.005.30.01EN · (0) 2019/02... -
Page 12: Start-Up
Follow the direction of rotation of the agitation components as indicated by the arrow attached to the engine. An incorrect direction of rotations results in a loss of agitation performance. Check the electrical consumption of the motor. INOXPA S.A.U. 20.005.30.01EN · (0) 2019/02... - Page 13 ATTENTION Do not modify the operating parameters for which the agitator was initially designed without written authorisation from INOXPA (risk of damage and user hazard). Follow the instructions for use and the safety requirements described in the instructions manual for the tank in which the agitator is mounted.
-
Page 14: Troubleshooting
The attached table lists solutions to problems that may arise while operating the agitator. It is assumed that the agitator has been properly installed and that is has been selected correctly for the specific application. Contact INOXPA if technical assistance is required. Motor overload... -
Page 15: Maintenance
If the agitator is out of service for a considerable period of time, clean and treat the parts with VG46 mineral oil. The shaft must be stored in the horizontal position and on wooden supports or on supports of a similar material. INOXPA S.A.U. 20.005.30.01EN · (0) 2019/02... -
Page 16: Disassembly And Assemby Of The Agitator
Join the agitator shaft (05) with the head half shaft using the Allen pins (55A). Place the propeller (02) in the agitator shaft and tighten the Allen pins (55). Fit the agitator over the tank. INOXPA S.A.U. 20.005.30.01EN · (0) 2019/02... -
Page 17: Technical Specifications
Shaft length (mm) 1250 (max.) Shaft diameter (mm) 100 – 130 – 150 Propeller diameter (mm) Propeller Lineflux (type 18) 9.3. WEIGHTS Type agitator Weigh (kg) BCI1.18-4007-1-100 16,5 BCI1.18-4007-1-130 16,5 BCI1.18-4007-1-150 16,5 BCI1.18-6005-1-130 17,0 BCI1.18-6005-1-150 17,0 INOXPA S.A.U. 20.005.30.01EN · (0) 2019/02... -
Page 18: Dimensions
Technical Specifications 9.4. DIMENSIONS Agitator shaft Type agitator A BCI1.18-4007-1-100 1.610 BCI1.18-4007-1-130 1.610 BCI1.18-4007-1-150 1.610 BCI1.18-6005-1-130 1.610 BCI1.18-6005-1-150 1.610 INOXPA S.A.U. 20.005.30.01EN · (0) 2019/02... -
Page 19: Bci Agitator's Exploded Drawing And Parts List
AISI 316L Base plate AISI 316L Countersunk screw Allen screw Flat washer Allen pin Allen pin Elastic ring Steel Upper ball bearing Steel Lower ball bearing Steel V-ring Lip seal IEC Motor / Gear motor INOXPA S.A.U. 20.005.30.01EN · (0) 2019/02... - Page 20 How to contact INOXPA S.A.U.: Contact details for all countries are continually updated on our website. Please visit www.inoxpa.com to access the information. INOXPA S.A.U. Telers, 60 – 17820 – Banyoles – Spain Tel.: +34 972 575 200 – Fax: +34 972 575 502...
Need help?
Do you have a question about the BCI Series and is the answer not in the manual?
Questions and answers