Kenwood FP510 Series Manual page 5

safety
G
The blades and discs are very sharp, handle with care.
Always hold the knife blade by the finger grip
at the top, away from the cutting edge, both
when handling and cleaning.
G
Always remove the knife blade before pouring contents from the bowl.
G
Keep hands and utensils out of the processor bowl and liquidiser jug whilst
connected to the power supply.
G
Switch off and unplug:
G G before fitting or removing parts
G G after use
before cleaning
G G
G
Never use your fingers to push food down the feed tube. Always use the
pusher/s supplied.
G
Before removing the lid from the bowl or liquidiser/mill from the power unit:-
G G switch off;
wait until the attachment/blades have completely stopped;
G G
G G Be careful not to unscrew the liquidiser jug or mill from the blade unit.
G
Allow hot liquids to cool before blending in the liquidiser - if you haven't fitted
the lid securely and it comes off, you could get splashed.
G
This machine will be damaged and may cause injury if the
interlock mechanism is subjected to excessive force.
G
Do not use the lid to operate the processor, always use the on/off speed
control.
G
This machine is not intended for use by young children or infirm persons without
supervision.
G
Never use an unauthorised attachment.
G
Don't let children play with this machine.
G
Never leave the machine on unattended.
G
Never use a damaged machine. Get it checked or repaired: see 'service'.
G
Never let the power unit, cord or plug get wet.
G
Don't let excess cord hang over the edge of a table or worktop or touch hot
surfaces.
G
Never misuse your food processor and only use it for its intended domestic use.
before plugging in
G
Make sure your electricity supply is the same as the one shown on the
underside of your machine.
G
This appliance complies with European Economic Community Directive
89/336/EEC.
before using for the first time
1 Remove all packaging including the plastic blade covers from the knife blade.
Take care the blades are very sharp. These covers should be discarded
as they are to protect the blade during manufacture and transit only.
2 Wash the parts see 'cleaning'
key
processor
pushers
feed tube
lid
detachable drive shaft
bowl
safety interlock
cord storage (at back)
power unit
speed/pulse control
liquidiser outlet/interlock
liquidiser outlet cover/safety interlock
liquidiser
blade unit
sealing ring
jug
lid
filler cap
additional attachments
Not all of these attachments listed below will be included with your food
processor. Please refer to your content list supplied. To buy an attachment not
included in your pack, contact the dealer from whom you purchased your
appliance.
knife blade
dough tool (FP530 only)
twin beater geared whisk
maxi-blend canopy
thick slicing/coarse shredding disc
thin slicing/fine shredding disc (FP520/FP530)
fine (Julienne style) chipper disc (FP530 only)
rasping disc (UK pack - not supplied)
geared citrus press (FP520/FP530)
mill (if supplied)
KENSTORE™ attachments carousel
spatula
recipe book (if supplied)
to use your food processor
G
When using the food processor bowl, the liquidiser outlet cover
must be fitted and locked in position or the processor will not
work. Ensure the M on the outlet cover lines up with the L on the
power unit.
1 Fit the bowl. Place the handle towards the back, lower and turn clockwise until
it locks .
2 Then fit the detachable shaft
3 Fit an attachment over the drive shaft.
G
Always fit the bowl and attachment onto the machine before adding ingredients.
4 Fit the lid onto the bowl
the line on the outlet cover.
5 Switch on and select a speed.
G
The processor won't work if the lid or outlet cover are fitted
incorrectly.
G
Use the pulse (P) for short bursts. The pulse will operate for as long as the
lever is held in position.
6 Reverse the above procedure to remove the lid, attachments and bowl.
G
Always switch off before removing the lid.
important
G
Your processor is not suitable for crushing or grinding coffee beans, or
converting granulated sugar to caster sugar.
G
When adding almond essence or flavouring to mixtures avoid contact with the
plastic as this may result in permanent marking.
to use your liquidiser
1 Fit the sealing ring into the blade unit
Leaking will occur if the seal is damaged or not fitted correctly.
2 Screw the jug onto the blade unit.
3 Put your ingredients into the jug.
4 Put the filler cap in the lid, then turn.
5 Turn the lid in a clockwise direction to lock onto the jug.
6 Remove the liquidiser outlet cover by turning in an anti-clockwise direction.
7 Place the liquidiser onto the liquidiser outlet and turn to lock
2
over the power unit fixed shaft.
- turn clockwise until the arrow on the lid aligns with
- ensuring the seal is located correctly.
.