Table of Contents
Advertisement
Available languages
Available languages
tool (see technical data). The minimum conductor
size is 1.5 mm
2
.
When using a cable reel, always unwind the cable
completely.
Also refer to the table below.
2
Conductor size (mm
)
0.75
1.00
1.50
2.50
4.00
Cable length (m)
Voltage
Amperes
115
0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 20.0
220/240
0
- 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 20.0
Assembly and adjustment
Prior to assembly and adjustment always
unplug the tool.
Inserting and removing 19 mm Hex. accessories
(fig. B)
Your D
WALT Demolition Hammer uses accessories
E
with 19 mm Hex. tool shank (refer to the inset in fig. B
for a cross-section of a chisel shank).
• Grease the chisel shank.
Do not apply bit lubricant to the Power
Tool.
• Push in the tool locking bar (11) and turn it
through 180°.
• Insert the chisel shank into the tool holder (3).
• Push in the tool locking bar and turn it back into
the original position.
15
Cable rating (Amperes)
6
10
15
20
25
7.5
15
25
30
45
Cable rating (Amperes)
6
6
6
6
6
6
6
6
15
6
6
10
15
20
10
10
15
20
20
15
15
20
25
25
20
20
25
-
6
6
6
6
6
6
6
6
6
6
6
6
10
10
10
10
10
15
15
15
15
15
20
20
20
20
20
25
• Pull on the chisel to check if it is properly locked.
The hammering function requires the chisel to be
able to move axially several centimetres when
locked in the tool holder.
• Fit the dust cover (12) over the end of the tool
holder (3).
• To remove a chisel push in the tool locking bar (11),
turn it through 180° and pull the chisel out of the
tool holder.
Fitting the side handle (fig. C)
The side handle (4) can be mounted on the front of the
Demolition Hammer to suit both RH- and LH-users.
60
6
10
15
• Unscrew the side handle clamp wheel (5).
20
• If necessary, remove the side handle mounting
25
assembly and remount it on the opposite side of
-
the tool.
-
-
• Rotate the mounting assembly to the desired
6
6
position.
6
6
• Lock the side handle mounting assembly in place
15
by tightening the clamp wheel (5).
15
20
Instructions for use
-
• Always observe the safety instructions
• Be aware of the location of pipework and
• Apply a pressure of approx. 20 - 30 kg
Demolition, chasing and channelling (fig. A)
• Select the appropriate chisel and grease its shank.
• Insert the chisel and check if it is properly locked.
• Fit the dust cover (12).
• Fit and adjust the side handle (4) and tighten the
side handle clamp wheel (5).
• To run the tool press the ON/OFF-switch (1). The
tool now runs in continuous operation.
• To stop the tool press the locking switch (2)
briefly. Always switch OFF the tool when work is
finished and before unplugging.
Always operate the Demolition Hammer
with the side handle properly mounted.
and applicable regulations.
wiring.
to the tool. Excessive force does not
speed up chiselling but decreases tool
performance and may shorten tool life.
E N G L I S H
en - 4
Advertisement
Chapters
Table of Contents
