Setting Filtering Cycles; Suspension Of Filtering Cycles; Overheating During Filtering Cycles; Clearray - Jacuzzi Profile User Manual

Setting the filtering cycles
To set the filtering cycle:
Press the key "Filter"
Fdx, where "x" indicates the duration in hours.
Use the keys "Up"
sired duration. This may be from a minimum of 0 to a maximum
of 12 hours, which corresponds to constant filtering, since
the cycle runs every 12 hours in any case.
Press the "Filter" key again to confirm the selected val-
ue. You will then go to the start time (Fs).
First set the hour and confirm with the "Filter" key. Then set
the minutes, and press the "Filter" key again to memorize the
set values and exit programming.
When the function is on, the display will shown the respective
symbol.
NOTE: if there is a power outage, the set values will be pre-
served.
Suspending the filtering cycles
The filtering cycle may be suspended by the anti-freeze pro-
tection ("Smart Winter") or due to overheated water. Refer to the
respective chapters.
If the system is in standby mode (see related chapter), the fil-
tering pump stops and is restarted when the system is no longer
in standby mode.
If there is a power outage during a filtering cycle, or if it oc-
curs prior to the start of filtering and lasts after that time, the cy-
cle will not start when the power comes back on. Filtering will
be postponed until the next cycle, since the cycle is repeated
every 12 hours.

Overheating during filtering cycles

During the filtering cycle, if the water temperature exceeds
the setpoint by more than 1 °C (2 °F) (see the chapter on ad-
justing the water heating temperature) and it does not decrease
at least 1 °C (2 °F) in the following 3 hours, the filtering cycle
will be suspended.
Even if the water temperature is high (due to excessive sunlight,
for example), filtering is however ensured for at least 3 hours.
Clearray™ (UV light generator)
Use of the Clearray ™ normally reduces the need for chemical
water treatment additives and therefore also reduces costs.
Clearray™ operates automatically and is dependent on pump
activation; it remains off when the hydromassage, blower or even
just the spotlight are on (as it is presumed that there is some-
body in the tub); Clearray™ (where a filtering cycle is active)
begins operating once again 10 minutes subsequent to switch-
ing off the aforementioned functions.
. The display shows the message
and/or "Down" to insert the de-
Rapid filtering ("Instant Clear")
This is recommended after intensive use of the spa and/or is
associated with chemical treatment of the water, to favour the
dissolution of substances used for disinfection.
To activate the function, press the key "Instant Clear"
display will show the message boo.
The function lasts 45 minutes (this value cannot be changed).
During this time, the filtering pump and the hydromassage pumps
are turned on as follows:
- hydromassage pump 2 is activated only one time for one
minute.
- hydromassage pump 1 is activated for the rest of the cycle
(Clearray™ is on for the entire duration of the cycle).
If the heater is on, it will continue to run normally, unless the
system is configured for limitation of electrical consumption.
The function stops:
- when the aforementioned time expires
- when another function is turned on (except for the time and/or
the spotlight).
- when the key is pressed again
NOTE: if you need to activate the anti-freeze protection dur-
ing rapid filtering, rapid filtering will be temporarily suspend-
ed to allow the anti-freeze protection to be started.
I
ACTIVATION OF HYDROMASSAGE PUMPS
The hydromassage pumps are activated via the respective keys.
Refer to the user's manual to determine which jets are activated
by each pump:
Press the key "Pump 1"
Press the key "Pump 2"
pump.
The pump (or pumps) will run for 20 minutes, but can be turned
off before that by pressing the aforementioned keys again.
NOTES
- If the level of water in the compensation tanks is not correct,
the pumps are prevented from starting to protect them (also
see the chapter on checking operation and first start-up).
- When the hydromassage is started, the filtering pump is al-
so turned on, if it was not already. It will remain on for 10 min-
utes after the hydromassage is turned off.
30
.
to activate that pump.
to activate another hydromassage
. The