Advertisement
Quick Links
ASSEMBLY
IMPORTANT ASSEMBLY INFORMATION
• Need phillips screw driver and 2 adjustable wrenches (putting the trampoline together). A rubber mallet may make assembly
easier, however.
• Assembly requires two persons.
• Wear gloves to protect your hands from pinch points during assembly.
TRAMPOLINE PLACEMENT
1. Place the trampoline on a level surface before using it.
2. Adequate overhead clearance is essential. A minimum of 24 feet from ground level is best. Provide clearance for wires, tree
limbs, and other possible hazards. Lateral (sideways) clearance is also essential. Place the trampoline away from walls, struc-
tures, fences, and other play areas. Always have a clear space on all sides of the trampoline.
3. Use the trampoline in a well-lighted area. Electric lights may be required for shady areas.
4. Secure the trampoline against unauthorized and unsupervised use.
5. Remove any objects from beneath the trampoline.
6. The owner and supervisors of the trampoline are responsible to make all users aware of practices specified in this manual.
1. Make sure that you understand the information in the
box at the top of this page.
Lay two Top Tubes with attached sockets (2) (A and C in
the inset drawing) and one top tube (1) without socket (B
in the inset drawing) on the ground in the positions
shown. Make sure the Top Tubes are turned so the small
holes (spring holes) are facing the ground.
Insert one end of the Top Tube without socket (B) into
the socket of Top Tube C. Insert the opposite end of the
Top Tube without socket (B) in the end of Top Tube with
socket (A). The Top Tubes and Sockets should now
appear as shown in step 2, below.
2. Slide two Leg Extensions (3) onto a Brace (4) as
shown. The peak of the Brace (4) should point toward the
ground. Screw the two screws (8) into the legs (3) and
Brace (4).
Insert one of the Legs (3) halfway into one of the Sockets
(2) assembled in step 1. Insert the other Leg halfway into
the other Socket. Press down on both Legs at the same
time and fully insert them into the Sockets.
Note: You may need to pull outward on the Legs as you
insert them into the Sockets.
Repeat steps 1 and 2 three additional times to assemble
the remaining three leg sections.
2
A
Push Here
3
8
Pull
Here
2
11
2
1
B
Push Here
4
Peak
8
2
C
3
Pull
Here
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Skywalker Elite Series
Summary of Contents for Skywalker Elite Series
- Page 1 ASSEMBLY IMPORTANT ASSEMBLY INFORMATION • Need phillips screw driver and 2 adjustable wrenches (putting the trampoline together). A rubber mallet may make assembly easier, however. • Assembly requires two persons. • Wear gloves to protect your hands from pinch points during assembly. TRAMPOLINE PLACEMENT 1.
- Page 2 Make sure that the two warning decals (not shown) are on top of the Bed (Mat). Note: If you purchased the Skywalker Trampoline Combo, the enclosure was pre-installed on the Bed (Mat) (5) at the factory. Inspect the attachments of the enclosure Netting to the trampoline mat (bed).
- Page 3 Frame Pad so that the slits are directly above the Legs (3), as shown. (If you are using the Skywalker Trampoline Enclosure, go to the Skywalker Trampoline Enclosure User’s Manual, pages 8-11, for instructions in assembling the Enclosure.
- Page 4 Do not use the trampoline without the Frame Pad (6). The Frame Pad is designed to reduce the possibility of Sleeve injuries due to jumpers coming in contact with the tram- poline frame. If you do not have a Frame Pad, contact your dealer to obtain one.
-
Page 5: Exploded Drawing And Parts List
EXPLODED DRAWING AND PARTS LIST Qty. Description Qty. Description Top Tube Springs Top Tube with Socket #8 Sheet Metal Screw 3/4” Leg Extension User’s Manual and Safety Placard Brace Accessories Bag Stitched Bed with 80 V-rings Set of ASTM Frame Labels Frame Pad * These parts are not illustrated. - Page 6 ASSEMBLY ASSEMBLY (PUTTING THE ENCLOSURE TOGETHER) IMPORTANT ASSEMBLY INFORMATION • Need phillips screw driver and 2 adjustable wrenches (not included). • Assembly requires two adults. Keep children away from the trampoline enclosure until it is completely put together. • Use gloves to protect your hands from pinch points while putting the enclosure together. •...
- Page 7 3. Note: In Step 3 you will secure the Enclosure arches to the frame of the trampoline. Lift one of the arches assembled in Step 2 and insert the two Straight Tubes (6) into the tops of the two trampoline frame Square Sockets (4) as shown.
- Page 8 7, 8 4. Locate one strap(11) with D-rings to the upper edge of the Netting. Lift the end of the strap(11) and insert it through the small belt sewn on the upper edge of the netting,see the right drawing. Then Lift D-ring and hold small belt it close to an L-tube(7)as shown in Inset Drawing A.
- Page 9 Frame DISASSEMBLY (TAKING THE ENCLOSURE APART) To disassemble the trampoline enclosure (take it apart), follow assembly steps 1 through 7 in reverse order.
- Page 10 EXPLODED DRAWING AND PARTS LIST . y t . y t t - f i t t a t t s ’ r End Cap Specifications are subject to change without notice. ORDERING REPLACEMENT PARTS To order replacement parts, visit our web site at www.skywalkertrampoline.com or call our toll-free Customer Care Hot Line at 1-866-603-Jump (5867), Monday through Friday, 8 a.m.
Need help?
Do you have a question about the Elite Series and is the answer not in the manual?
Questions and answers