EMC Celerra NS40 Setting Up

Setting Up the EMC
1

Before You Begin

Shipping Rack
Disk-array enclosure
Standby power supply
LAN1
LAN2
Control Station
Storage processor
enclosure
Blade enclosure
2
Install Rails and Components in Rack
2a Install Blade Enclosure
Required parts:
• Blade enclosure number for the NS40 single blade P/N 100-520-326 or 100-520-328
• Adjustable rail kit P/N 100-561-802
• Bezel
Adjustable rail
2
Right front
Screw
Mounting
rail
3
Enclosure
Front
2b Install Storage Processor Enclosure
Required parts:
• Storage processor enclosure for the NS40 P/N 100-520-372
• Rail kit P/N 100-561-802
Storage processor
enclosure
SP B
Blade enclosure
Blade 3 (B 3)
1. In the 1U space above the blade enclosure, install the storage processor
enclosure as described in Step 2a Install Blade Enclosure.
Copyright © 2007 EMC Corporation. All rights reserved.
Front
Before you begin:
• The NS40 system you are about to install comes factory pre-loaded with Celerra Network Server software (DART) and
Storage Array software (FLARE).
is required, perform it after installation. For more information refer to Solution Case emc163262.
• Go to the Celerra Tools page for the latest information on the NS40 product: (http://Powerlink.EMC.com and select
Celerra Tools in the Navigator).
• Two people are required to lift several hardware components.
• Remove
injure yourself or damage the equipment.
CIP-000935
or dual blade P/N 100-520-327 or 100-520-329
Rear
Alignment
pin
Right rear
Front
Mounting rail
CIP-000921
Rear
CIP-000922
A
B
CIP-000914
Celerra
®
DO NOT PERFORM A FRESH INSTALL OF
only the 16 visible Phillips-head screws on the front of the mini-rack. Do not remove any of the other screws or you may
Required tools:
• Flathead screwdriver
• Manual Phillips-head screwdriver
Avoid stripping the screw-heads.
Alignment
Screw
pin
(2 per side)
Bezel
Screw (2)
Alignment
pin
1. Select 7U (12.25 in.) of available rack space for the NS40, plus 3U (5.25 in.) for each optional disk-array enclosure
(1U =1.75 inches).
NOTE: Use the supplied clip nuts if required for your rack.
2. Starting at the bottom of the selected rack space,
a. From the cabinet front, insert the rail alignment pin into the middle hole of the 1U space on the right side at the the
rear of the cabinet. Orient the rails so the sliding insert faces the inside of the rack.
b. Extend the rail to the front of cabinet, aligning the rail holes with the channel holes (the verticle metal bar with
evenly spaced holes) on the inside of the cabinet.
c. Install but do not tighten one of the provided screws in the top hole on the front of the rail through the cabinet channel.
d. From the cabinet rear, insert
cabinet channel.
e. Repeat steps b-e to install the left rail.
3. Two people are required for this installation:
of another person, slowly slide the blade enclosure into the rails until the front assembly flanges are flush with the cabinet channels.
4. Do not insert any new screws, but tighten the screws on each end securing the mounting rails to the cabinet channels.
5. Insert two of the provided screws into the middle and bottom holes of each rail catch. Attach the bezel rail catches to the holes
in the rail flanges on the front of the cabinet. Then press the bezel onto the rail catches until it snaps into place.
2c Install Control Station
Required parts:
• Control Station P/N 100-520-606
• Rail kit P/N 100-520-527
• Adjustable Rail Installation kit
SP A
B 2
1
NS40 System
®
SOFTWARE. If a software upgrade (not fresh install)
When installing the disk-array enclosures in the cabinet, do not remove the disks.
4
Enclosure
Rail
catch
Front
mount one set of 1U rails for the blade enclosure as follows:
Always ensure the rail is level.
but do not tighten two screws in the top and bottom holes on the rail back through the
From the cabinet front, align the blade enclosure with the mounting channels.
Control Station
Storage processor
enclosure
A
SP B
B
Blade enclosure
Blade 3 (B 3)
NOTE: Do not remove the Control Station label at this time.
1. In the 1U space above the storage processor enclosure,
install the Control Station as described in
Rear
Indentation
to center of
the rack
CIP-000923
With the help
SP A
B 2
CIP-000915
Step 2a Install Blade Enclosure.
300-004-901 Rev A01