Digital Equipment DECpc AXP 150 User Information
Controller, compaq qvision 1024/e
Hide thumbs
Also See for DECpc AXP 150:
- Customer technical information (276 pages) ,
- User information (28 pages) ,
- User information (122 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Information
DECpc AXP 150
COMPAQ QVision 1024/E Controller
User Information
Order Number: EK-A0653-UG.001
July 1993
This manual describes how to install, configure, and use the
COMPAQ QVision 1024/E controller in the DECpc AXP 150 system.
Revision Information:
This is a new manual.
Digital Equipment Corporation
Maynard, Massachusetts
Advertisement
Table of Contents
Related Manuals for Digital Equipment DECpc AXP 150
Summary of Contents for Digital Equipment DECpc AXP 150
-
Page 1: User Information
COMPAQ QVision 1024/E Controller User Information Order Number: EK-A0653-UG.001 July 1993 This manual describes how to install, configure, and use the COMPAQ QVision 1024/E controller in the DECpc AXP 150 system. Revision Information: This is a new manual. Digital Equipment Corporation Maynard, Massachusetts... - Page 2 The postpaid Reader’s Comments form at the end of this document requests your critical evaluation to assist in preparing future documentation. The following are trademarks of Digital Equipment Corporation: AXP, DEC, DECpc, Digital, VAX DOCUMENT, the AXP logo, and the DIGITAL logo.
- Page 3 FCC Notice: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
-
Page 5: Table Of Contents
Contents Preface ........... . . 1 Installing the QVision Controller Introduction . - Page 6 A Specifications Introduction ........A–1 In This Appendix .
-
Page 7: Preface
This manual is intended for anyone installing, configuring, or connecting the COMPAQ QVision 1024/E controller in a DECpc AXP 150 system. It is written for both experienced and inexperienced users. This manual contains three chapters, an appendix, and an index... - Page 8 The following conventions are used in this manual: Conventions Convention Description Text displayed on the screen is shown in monospace monospace type. italic type Italic type emphasizes important information, indicates variables, and indicates complete titles of manuals. n.nn A period in numerals signals the decimal point indicator.
-
Page 9: Installing The Qvision Controller
Installing the QVision Controller Introduction This chapter describes how to install and connect the QVision 1024/E controller. About the The QVision 1024/E controller is used in an EISA-based personal QVision 1024/E computer or system. It allows you to connect a super video Controller graphics array (SVGA) monitor to the system. -
Page 10: Before You Begin
(SECOND) setting on all other QVision controllers. Installation For information on opening the system unit and installing an Procedure option board, see the DECpc AXP 150 and DEC 2000 Model 300 AXP Customer Technical Information manual. 1–2 Installing the QVision Controller... -
Page 11: Qvision Controller Illustration
Installing the QVision Controller Figure 1–1 shows the position of the switch that controls QVision Controller whether the QVision controller is the primary or secondary video controller. Illustration Figure 1–1 QVision 1024/E Controller Switches SECOND TEST PRIM GA_EN00499A_93A Installing the QVision Controller 1–3... -
Page 12: Connecting The Monitor
Connecting the Monitor Connecting the Monitor Important Note Information You must reconfigure the system before you can use the monitor. See Chapter 2 for more information. Connection Figure 1–2 shows how to connect the monitor to the SVGA port Procedure on the QVision controller. -
Page 13: Configuring The Qvision Controller
Configuring the QVision Controller Introduction This chapter describes how to configure the system after you have installed the QVision 1024/E controller. This chapter contains the following section: In This Chapter • EISA Configuration Utility (ECU) Configuring the QVision Controller 2–1... -
Page 14: Eisa Configuration Utility (Ecu)
To configure the QVision controller within the system or to change the configuration settings, you must run the ECU. See the DECpc AXP 150 and DEC 2000 Model 300 AXP Customer Technical Information manual for information on running the ECU. -
Page 15: Default Configuration
EISA Configuration Utility (ECU) Table 2–1 (Cont.) Configuration Settings Function Choice of Settings Advanced Video Features: Extended ROM Extended ROM supported Advanced VGA ROM support only No ROM support High Address Video Buffer Enabled Disabled Video Interrupt Disabled Enabled Video Controller Order First Second Third... -
Page 17: Troubleshooting
Troubleshooting This section describes some of the problems that can occur with Summary the QVision 1024/E controller. It suggests possible causes for the problems and actions that you can take to correct them. Identifying Table 3–1 describes how to identify and solve problems by and Solving interpreting correctly the symptoms that are occurring. - Page 18 See the monitor documentation for incorrectly. more information. The system power-up The QVision controller See the DECpc AXP 150 and DEC test displays a VGA is faulty. 2000 Model 300 AXP Customer error. Technical Information manual for information on testing option boards.
-
Page 19: Introduction
Specifications Introduction This appendix lists the specifications for the QVision 1024/E controller. In This This chapter contains the following sections: Appendix • QVision Controller Specification • SVGA Connector Pin Specification Specifications A–1... -
Page 20: Qvision Controller Specification
QVision Controller Specification QVision Controller Specification Table A–1 lists the physical specifications for the QVision QVision Controller controller. Specification Summary Table A–1 Specification Table Host Interface 32-bit RAM 16-bit ROM 1 Megabyte Board Address RAM (DOS Video Address) A0000 - BFFFF RAM (High Address) 1 Megabyte - 4 Gigabytes C0000 - C7FFF 32 Kbytes... -
Page 21: Svga Connector Pin Specification
SVGA Connector Pin Specification SVGA Connector Pin Specification This section lists the pin specifications for the SVGA connector. Summary SVGA Figure A–1 shows the pin numbers on the SVGA connector. Connector Illustration Figure A–1 SVGA Connector GA_EN00289A_93A Table A–2 describes the functions of the pins on the SVGA SVGA connector. -
Page 23: Index
Index Configuring the QVision controller Installing the QVision controller changing the configuration, 2–2 installation procedure, 1–2 configuration settings, 2–2 preparation, 1–2 running the ECU, 2–2 Connecting the monitor, 1–4 Specifications QVision controller specification, A–2 EISA Configuration Utility, 2–2 SVGA connector pin specification, A–3 Switch settings, 1–2 Troubleshooting, 3–1 Index–1...