Timer; Sleep Timer - Philips FW-C28/22 User Manual

TIMER

5 Press CLOCK•TIMER again to store the
setting.
™ The clock starts.
• To exit without storing the setting, press
Ç on the system.
Notes:
– During clock setting, if no button is
pressed within 90 seconds, the system
will exit clock setting mode
automatically.
– When a power interruption occurs, the
clock setting is erased.
To set the time with RDS clock, see
"Receiving RDS Radio Station" under
TUNER section.
Timer Setting
• The system can switch on to CD,
TUNER, or TAPE 2 mode automatically
at a preset time. It can serve as an
alarm to wake you up.
• Before setting the timer, make sure the
clock is set correctly.
• The timer will always be switched on
once it is set.
• The volume of the timer will
increase from the minimum level
until the volume level before the set
is switched to standby mode.
pg 01-24/C28/22-Eng 21
1 Press and hold CLOCK•TIMER for more
than 2 seconds to select timer mode.
™ "12:00 " or "00:00" or the last
AM
timer setting starts flashing
depending on whether you have
selected 12- or 24-hour mode.
™ The
starts flashing.
TIMER
™ The selected source is lit while other
available sources are flashing.
2 Press CD, TUNER or TAPE to select the
desired source.
• Before selecting CD or TAPE, make sure
a CD or tape is loaded in the CD tray or
tape deck 2.
3 Press à or á on the system to set the
hour for the timer to start.
4 Press í or ë on the system to set the
minute for the timer to start.
5 Press CLOCK•TIMER to store the start
time.
™ The timer is now set.
™ The remains on the display.
TIMER
• At the preset time, the timer will be
activated.
™ The selected source will be played.
Notes:
– During timer setting, if no button is
pressed within 90 seconds, the system
will exit timer setting mode
automatically.
– If the source selected is TUNER, the last
tuned frequency will be switched on.
– If the source selected is CD, playback
will begin with the first track of the
selected disc or program. If the CD trays
are empty, the TUNER will be selected
instead.
– The timer will not activate if a recording
is in progress.
To switch off the TIMER
1 Press and hold CLOCK•TIMER for more
than 2 seconds .
2 Press Ç on the system to cancel the
timer.
™ The timer is now switched off.
™ The display will show "CANCEL"
and the disappears.
TIMER
To start the TIMER again (for the same
preset time and source)
1 Press and hold CLOCK•TIMER for more
than 2 seconds .
2 Press CLOCK•TIMER again to store the
start time.
™ The timer is now on.
™ The appears on the display.
TIMER
3/7/00, 5:15 PM

SLEEP TIMER

Sleep Timer
(only on remote control)
This feature allows you to select a length
of time after which the system will switch
to the standby mode automatically.
1 Press SLEEP on the remote control
repeatedly to select a period of time.
™ The selections are as follows (time in
minutes):
60 ™ 45 ™ 30 ™ 15 ™ OFF ™ 60
...
™ "SLEEP XX" or "OFF" will be
displayed. "XX" is the time in
minutes.
2 When you reach the desired length of
time, stop pressing the SLEEP button.
™ After this amount of time passes, the
system will switch to the standby
mode.
To switch off the Sleep Timer
• Press SLEEP repeatedly until "OFF" is
displayed, or press the STANDBY ON
button.
3139 116 19331 3139 116 19331
21