Brandt VI 310 Operating Instructions Manual page 26

Présentation de votre lave-vaisselle Troubleshooting, what to do?
If you are in any doubt about the operation of your machine, before calling a qual-
ified engineer, check the following points (depending on the symptoms noticed).
When first using the machine Possible causes
- The machine is wobbly,
Small door leak
not level
- The door is not correct-
ly centred on the tub
- The seal's lip has been
flattened during storage
- Leak at the tap
Small leak around or
under the machine (move
- Leak in the machine
the machine to locate the
leak better)
- The machine or the
The door "catches" when
door is not correctly
you close it
centred on the tub
- The door springs are
The door falls down
not tensioned enough
heavily when you open it
to compensate for the
(integratable models)
weight of the basket.
- The door springs are
The door is not level
over-tensioned.
when open or goes back
up too quickly (integrat-
- No wooden panel
able machine)
- Poor handling (the bas-
The upper basket will not
ket has been pulled
stay in the high position
upwards too quickly).
Programming, display anomalies Possible causes
- The energy-saving pro-
The cycle takes too long.
grammes take longer
because they compensate
for the lower washing and
drying temperatures by
longer agitation and drying.
48
What to do
- Adjust the adjustable
feet
- Adjust the rear feet
- Take off the door seal
.
all around the door.
- Check that the seal is pre-
sent and re-tighten the nut
- Close the water tap and
call an engineer.
- Recentre the door by
adjusting the rear feet.
- Contact the installer.
- Tighten the two tensioning
screws accessible through
the holes in the two side
panels.
- Contact the installer.
- Loosen the two tensioning
screws accessible through
the holes in the two side
panels.
- Fit a wooden panel to the
door (a chipboard panel OK
if on a temporary basis)
and adjust the springs.
- Contact the installer.
- Move the basket gradu-
ally on one side and
then the other (until
you hear a "Click") = ->
see the Operating Instructions.
What to do
- Use these programmes
preferably at night
when the length and
the finishing time are
not important.
GB
Présentation de votre lave-vaisselle Troubleshooting, what to do?
Programming, display anomalies Possible causes
The lights light up one - Wrongly programmed.
after another
The Salt light does not go - No salt or too little salt
out in the reservoir to trig-
ger the float.
Poor operation Possible causes
The machine cuts off - Insufficient amperage to
supply all the equip-
ment being used at the
same time.
- Internal fault in the
machine
The machine will not - No power supply to the
start socket
- The tap is closed
- The water supply hose
is kinked
- Programme selection
error and programme
blocked
- "Start" button held down
too long (> 2 seconds)
- Safety system (anti-leak)
The machine does not - Protective cover on the
drain. sink's U bend not removed
- Drainage hose kinked
- Drain filter totally
blocked
- Pump blocked.
GB
What to do
- Cancel the current pro-
gramme by holding
down the "Start" button
for 3 seconds and then
reprogramme.
- Fill the reservoir and
wait until the cycle
ends. If the water is
soft enough not to
require salt, the Salt
light is permanently lit.
What to do
- Check the plug's ampe-
rage (10A minimum)
and the meter's capacity
- Call an engineer.
- Check the socket and
the fuse
- Check that the tap is
open
- Check that hose run
- Cancel by pressing
"Start" for 3 seconds
and reprogramme
- Press "Start" only briefly
to start the programme
- Call an engineer.
- Remove the protective
cover
- Check the hose runs cor-
rectly behind the machine
- Remove the filters and
clean them and the
drain hole
- Start a soak programme.
If the fault persists, call
an engineer.
49