Related Manuals for Clarke CWB1700P
Summary of Contents for Clarke CWB1700P
- Page 1 CWB1700P.fm Page 1 Wednesday, November 27, 2019 11:49 AM WORKBENCH MODEL NO: CWB1700P PART NO: 4501510 OPERATION & MAINTENANCE INSTRUCTIONS LS1119...
-
Page 2: Specifications
CWB1700P.fm Page 2 Wednesday, November 27, 2019 11:49 AM INTRODUCTION Thank you for purchasing this CLARKE WorkBench. Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to your purchase giving you long and satisfactory service. -
Page 3: Carton Contents
CWB1700P.fm Page 3 Wednesday, November 27, 2019 11:49 AM CARTON CONTENTS The following items should be supplied in the carton. If any parts are missing or damaged, please see your CLARKE dealer where you purchased the workbench. Left Left Drawer Slide (Type A) x 4 Drawer Bottom x 5... - Page 4 CWB1700P.fm Page 4 Wednesday, November 27, 2019 11:49 AM ASSEMBLE THE DRAWERS 1. Fit the drawer sides to the drawer bottom as shown and use two M4x8 bolts, washers and nuts in the central 2 holes to secure in place.
- Page 5 CWB1700P.fm Page 5 Wednesday, November 27, 2019 11:49 AM 3. Connect the drawer front to the assembly as shown using 5 M4x8 Bolts, washers and nuts. 4. Repeat steps 1-3 for the remaining four drawers, giving you a total of five drawers 5.
- Page 6 CWB1700P.fm Page 6 Wednesday, November 27, 2019 11:49 AM 6. Fit the drawer slides (Type ‘A’) to two of the drawers as follows • Extend the drawer slide by hand • Line up the drawer slide with the top of the drawer as shown.
- Page 7 CWB1700P.fm Page 7 Wednesday, November 27, 2019 11:49 AM ASSEMBLE THE MAIN FRAME 1. Locate and identify the three legs as shown. 2. Connect the upper panel to the left leg as shown using 3 M5x8 Bolts, washers and nuts.
- Page 8 CWB1700P.fm Page 8 Wednesday, November 27, 2019 11:49 AM 3. Connect the lower panel to the left leg as shown using 3 M5x8 Bolts, washers and nuts. 4. Fit the divider between the upper and lower panels using 4 M5x8 Bolts, washers and nuts.
- Page 9 CWB1700P.fm Page 9 Wednesday, November 27, 2019 11:49 AM 5. Connect the middle leg to the upper and lower panels as shown using 6 M5x8 Bolts, washers and nuts. 6. Carefully stand the workbench up and fit the back panel as shown using 12 M5x8 Bolts, washers and nuts.
- Page 10 CWB1700P.fm Page 10 Wednesday, November 27, 2019 11:49 AM 7. Remove the 3 M5x8 Bolts, washers and nuts that connect the middle leg to the upper panel, this is nessecery to enable you to fit the door. 8. Fit the door as shown and then replace the 3 M5x8 Bolts, washers and nuts that you removed in the previous step.
- Page 11 CWB1700P.fm Page 11 Wednesday, November 27, 2019 11:49 AM 9. Place the shelf into position. 10. Tighten up all the nuts and bolts. 11. Fit the adjustable feet to the bottom of the legs including the right leg which will be fitted later.
- Page 12 CWB1700P.fm Page 12 Wednesday, November 27, 2019 11:49 AM FITTING THE TOP AND RIGHT LEG 1. Lay the top upside down on the frame with the front towards you. 2. Lay the two completed drawers (with slides fitted on page 6) into position and secure using 8 wood screws supplied.
- Page 13 CWB1700P.fm Page 13 Wednesday, November 27, 2019 11:49 AM 3. With assistance, flip the top over and into postion as shown 4. Secure to the frame with 6 wood screws. 5. Place the right leg into postion and secure with 3 wood screws.
- Page 14 CWB1700P.fm Page 14 Wednesday, November 27, 2019 11:49 AM 6. Fit the support brackets as shown using wood screws and M5x8 bolts, washers and nuts • The larger bracket is fitted to the rear of the bench Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
- Page 15 CWB1700P.fm Page 15 Wednesday, November 27, 2019 11:49 AM FITTING DOOR LOCK IMPORTANT: Ensure the key remains in the lock until lock is fully fitted. 1. Remove the locking lever securing screw and lock washer from the lock assembly, remove the lever, spring washer and washer noting which way round they are fitted for reassembly.
- Page 16 CWB1700P.fm Page 16 Wednesday, November 27, 2019 11:49 AM FITTING THE LOWER DRAWERS 1. Insert the tongues into the slots on the legs and allow the drawer slide to swing down and rest on the leg, no fixings are requires 2.
- Page 17 CWB1700P.fm Page 17 Wednesday, November 27, 2019 11:49 AM 4. Make sure that you tighen all bolts and screws 5. Before using the bench for the first tme, we recommend the application of a waterproof wood preservative to the bench top to prevent staining from oil spills etc.
- Page 18 CWB1700P.fm Page 18 Wednesday, November 27, 2019 11:49 AM Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
- Page 19 CWB1700P.fm Page 19 Wednesday, November 27, 2019 11:49 AM Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
- Page 20 CWB1700P.fm Page 20 Wednesday, November 27, 2019 11:49 AM...