Lega 6962 Instruction Manual page 22

'Tempo dosata'
(batching time) is the honey packing time.
'Tempo sosta dopo dosata'
and turntable restart.
These values are valid with the packer set for 1, 2 or 4 packing cycles.
6) Use the R.-H. direction arrow (2) to highlight the value to change.
7) Use the UP (1) or DOWN (4) arrow keys to adjust the value.
8) After entering the new data, press OK (5) to store the changes.
9) Use the arrow UP (1) or arrow DOWN (4) keys to switch from the T.DOSE (batching time) screen display
to the T.RUOTE (waiting time after batching) or the PRUDUCI 1 screen displays; after completing the
new data entry press OK (5) to store the changes.
10) From the PRODUCI 1 screen display (pictured on page 7), it is possible to set the number of jars to fill by
adjusting the item "On" using the direction arrows. The item "Off" may not be modified, while the item
"Cnt" refers to the number of jars filled during the work cycle.
11) Press the ESC (6) key twice. The home page will be displayed. The machine is now ready to work
according to your newly entered values.
12) At the end of each work cycle, reset the screen display by holding down the emergency resetting control
(page 10, item 26) for approximately 10 seconds.
4.1.1 Instructions for resetting product 4.1.1 Instructions for resetting product 4.1.1 Instructions for resetting product 4.1.1 Instructions for resetting production
LEGA LEGA LEGA LEGA
srl srl srl srl
C C C C ostruzioni ostruzioni A A A A pistiche
ostruzioni ostruzioni
www.legaitaly.com www.legaitaly.com - - - - Tel 054626834 www.legaitaly.com www.legaitaly.com
(waiting time after batching) is the time that elapses between honey packing end
By selecting F4 followed by the R.-H. direction arrow (2), the
WARNING! WARNING! WARNING! WARNING! The supplier declines all responsibility for any
software fault resu software fault resulting from incorrect use or failure to
software fault resu software fault resu
comply with directions. comply with directions. comply with directions. comply with directions.
ion ion capacity ion capacity capacity capacity
Press F1 to view the screen shown here.
The first figure on the left shows daily production, the second
figure on the right shows total number of jars filled.
To reset the first figure, press and hold down the
"EMERGENCY RESET" key for more than three seconds.
To reset the second figure, press and hold down the
"EMERGENCY RESET" key for more than ten seconds.
If total number of jars filled is set to 999.999, the machine will
stop and regular work will be prevented.
It this case it will be necessary to reset the machine as
explained above.
pistiche – – – – via Maestri del Lavoro 23 via Maestri del Lavoro 23 – – – – 48018 Faenza
pistiche pistiche via Maestri del Lavoro 23 via Maestri del Lavoro 23
Tel 054626834 – – – – Fa Tel 054626834 Tel 054626834
machine troubleshooting screen will be displayed which
can be checked over the phone with one of our
technicians in case of faults.
The supplier declines all responsibility for any The supplier declines all responsibility for any The supplier declines all responsibility for any
lting from incorrect use or failure to
lting from incorrect use or failure to lting from incorrect use or failure to
Fa Fax 054628279 Fa x 054628279 x 054628279 x 054628279 – – – – P.iva 00043230390 P.iva 00043230390 P.iva 00043230390 P.iva 00043230390
48018 Faenza
48018 Faenza 48018 Faenza
22 / 68