Kohler Finial K-20012T-CP Installation Instructions Manual page 10

用户须知（续）
如图示:
(1) 快速闪烁，代表感应龙头正处于通电后
的两分钟自动调节阶段。期间，安装者、使
用者不得干扰其自动调节，感应范围内不要
放置物体。
(2) 间隔6秒钟闪烁一次（直流版本），表
示电池即将使用完，请更换电池。
(3) 间隔2秒钟闪烁一次：若直流感应龙头,
代表龙头电池耗尽，已停止工作，等待使
用者更换电池;若交流感应龙头，表示为两
种情况：一种为刚刚停电；另一种为在交
流供电正常的情况下，则电源盒直流接线
端接触不良。
(4) 在正常工作情况下，当有物体被感应
时，龙头出水，感应指示灯闪烁一次.(龙头
关闭，感应指示灯不闪烁）
2.
超时出水控制
连续在感应状态下使用约一分钟，龙头自动止水。
自动止水后，手或物体离开感应范围后，再次进
入感应范围内，龙头正常工作，否则无反应。
3. 清洗过滤系统
该感应龙头的阀体组件内已包含了优良的过滤装
置。如管内杂质过多或水质较差，长期使用会引
起出水情况不良。请按以下步骤清洗过滤装置：
1.
关闭角阀。
2.
将主阀体组件取下，拿出滤网
(19)(20)，用水冲洗完毕后，重新
装入。
注意：在清洗完滤网后，不要遗失
平垫。
4. 自动清洗存水功能
感应龙头长期处于不使用状态时，
每间隔24小时自动冲水一段时间排
出龙头内的存水。
10
IMPORTANT CONSUMER INFORMATION
(Continued)
指示灯
Indicator Light
2. Timeout setting
When the faucet flows continuously for 1 minute, the
faucet will automatically stop.Objects must be removed
from the sensing range. Then the water will flow when
objects re-enter into the sensing range again. Otherwise,
the faucet will not work.
3. Clean the Filtration System
The faucet includes connector assembly with high quality
filtration system. Excessive debris and water of bad
quality can cause block in the pipe, thus reducing water
flow. Please clean th filtration system as following:
1. Close the stop valve.
2. Remove the valve assembly and take out the
filter(19)(20)for cleaning, then re-install it.
19
20
NOTE: Ensure that the filter washer is installed after the
filter is cleaned.
4. Self-Cleaning the stagnant water
When the faucet is no used for a long period of time, it will
automatically flush to discharge the stagnant water inside
the faucet every 24hrs.
As shown:
(1) Quick flashing means the faucet is in the
period of adjusting sensing distance after power
on for 2 minutes. During these 2 minutes, please
do not disturb auto adjustment or place objects
within the sensing range.
(2) The indicator flashes every 6 seconds (DC
type) indicates that the unit is out of battery and
has stopped working. Replease batteries.
(3) The indicator flashes every 2s: as for DC type
faucets, this indicates the unit is out of battery and
ceases working. Please replace batteries. For AC
faucet, it indicates two possibilities: one is that the
unit is out of battery; or poor DC terminal contact
under normal AC power supply.
(4) Under normal condition, the water will flow and
the indicator will flash once when objects are
detected. (The indicator does not flash when
faucet stops flowing.)
1293596-T01-A