Related Manuals for Barco BarcoData 2100 LC
Summary of Contents for Barco BarcoData 2100 LC
- Page 1 BARCO PROJECTION SYSTEMS RETRO BLOCK DATA 2100LC R9001168 INSTALLATION MANUAL Date : 200598 Rev 00 Art. No : R5975349A...
- Page 2 Produced by BARCO NV, May 1998. All rights reserved. Trademarks are the rights of their respective owners. BARCO nv/Projection Systems Noordlaan 5 B-8520 Kuurne Belgium Tel : +32/56/368211 Fax : +32/56/351651 E-mail : sales.bps@barco.com Visit Barco at the web : http://www.barco.com Printed in Belgium...
-
Page 3: Table Of Contents
Table of Contents TABLE OF CONTENTS TABLE OF CONTENTS ................................. I-1 POWER CONNECTION ..............................1-1 Power (mains) cord connection ................................. 1-1 Fuses ........................................1-1 Switching on ....................................... 1-1 Lamp lifetime ....................................... 1-2 Switching to stand-by..................................1-2 Switching off ...................................... 1-2 PASSWORD SET UP ................................ -
Page 4: Power Connection
Power Connection POWER CONNECTION Power (mains) cord connection Use the delivered power cord to connect your projector to the wall outlet. Plug the female power connector into the male connector at #ÃPu €Ã à ! X ÃUP ÃGP8 6Gà Ã8P I U SP GÃÃPI G`à ÃÃGÃÃÃÃÃ... -
Page 5: Lamp Lifetime
The different values are shown in Table 1. S('!($ 9v€€vt Do not use it longer. Always replace with a same type of lamp. Call a BARCO authorized service technician for lamp replacement. @p‚‚€vp "$ S('!(% I‚…€hy... -
Page 6: Password Set Up
Password Set Up PASSWORD SET UP How to Enable or Disable the Password The password function is enabled/disabled when the password strap plug on the controller circuit board module is installed in the specified way. To get access to the controller circuit board module, proceed as follows: Œ... -
Page 7: How To Change The Password Menu
Password Set Up How to Change the Password Menu SERVICE First enter into the Service mode (refer to the Owners manual Chapter 10 for exact procedural steps.) IDENTIFICATION CHANGE PASSWORD Then highlight Change password by pressing the control disc up or CHANGE LANGUAGE CHANGE PROJ. -
Page 8: Off-Axis Projection
Off-axis Projection OFF-AXIS PROJECTION Off-axis projection The projector can be adapted to off-axis installation in order to meet environmental conditions. The range within which the projection angle can be changed is 0° (= on-axis) to 10° downwards for the QSD(0.8:1) and QSD(1.2:1) lens. 5HDU7DEOH Q…‚wrp‡v‚Ãhtyr For every possible installation a number of things have to be geared... - Page 9 Off-axis projection In order to change the discrete off-axis, the procedure described below has to be executed. Œ Remove the lens from the lens holder by turning it counter clockwise and put it in safe place (where it can't fall or be scratched by something).
- Page 10 Off-axis Projection Remount the lens mounting in such a way that the holes corresponding to the chosen projection-angle/lens combina- tion are just in front of the screw holes foreseen in the projector housing for the fixing screws. è Put the screws in the screw holes and fasten them. è...
- Page 11 Off-axis projection d) Mechanical shift Place the projector in its correct working position. Adjust the lens holder to its reference position using the mechani- cal shift. This is reached when the gap (indicated with a white arrow) coincides with the reference hole (indicated with a white circle). ë...
Need help?
Do you have a question about the BarcoData 2100 LC and is the answer not in the manual?
Questions and answers