Page 3
PRODUCT INSTALLATION & SAFETY INSTRUCTION These instructions are for your safety. Please read the following instructions carefully before proceeding with the installation and use of this appliance. Keep the instruction manuals for future reference. Warning: All installation work must be carried out by a suitably qualified person, strictly following local building regulations and these instructions.
Page 4
PRODUCT INSTALLATION & SAFETY INSTRUCTION Warning: This appliance is supplied with a three core supply cord and must be connected direct to the mains electricity supply via a omni-polar or double pole switch having a 3mm minimum contact gap on each connector. This appliance should be connected to a circuit which incorporates an isolating switch providing full disconnection from the power supply.
PRODUCT INSTALLATION & SAFETY INSTRUCTION INSTALLATION Due to himidity issue may damage the hob electronics, the hob is not recommended be installed directly above a dishwasher, fridge, freezer, washing machine or clothes dryer. The wall, countertop and any area closed by the cooking zone shall withstand heat. To avoid any damage, the sandwich layer of the countertop and adhesive must be resistance to heat.
PRODUCT INSTALLATION & SAFETY INSTRUCTION The installer must ensure that the correct electrical connection has been made and that it is compliant with safety regulations. Disconnection must be incorporated in the fixed wiring in accordance with the wiring rules. Note: For I 3060 BK HK / H 3060 BK HK / I 4060 BK HK model, this appliance requires a 32 Amp Miniature Circuit Breaker.
Page 7
Model : I 2030 BK HK Model : H 2070 BK HK INDUCTION HOB MIXED HOB Model : I 2070 BK HK Model : H 3060 BK HK INDUCTION HOB INDUCTION FREE ZONE HOB Model : I 3060 BK HK...
As shown below: Model L(mm) W(mm) H(mm) D(mm) A(mm) B(mm) X(mm) I 2030 BK HK ≥50 I 2070 BK HK ≥50 H 2070 BK HK ≥50 I 3060 BK HK ≥50 H 3060 BK HK ≥50...
Page 9
PRODUCT AND BUILT-IN DIMENSION Model A(mm) B(mm) C(mm) E(mm) I 2030 BK HK ≥50 ≥20 Air intake Air exit (≥5) I 2070 BK HK ≥50 ≥20 Air intake Air exit (≥5) H 2070 BK HK ≥50 ≥20 Air intake Air exit (≥5) I 3060 BK HK ≥50...
Page 10
ASSEMBLY BEFORE INSTALL THE HOB, MAKE SURE THAT The worktop is square and level, and no structural members interfere with space requirements. The wall and the induced heating zone, near or above the worktop should be made of heat- resistant material.
Page 12
USING THE TOUCH / TOUCH SLIDER CONTROLS The controls respond to touch, no need to apply any pressure. Use the ball of the finger, not its tip. A “beep” sound will be responded each time when a touch is registered. ...
Indicators Reference and Description POWER LEVEL / TIMER SETTING MELTING / HEATING / SIMMERING / TIMER FREE ZONE DEFROSTING WARMING ~ BOILING CONNECT Slow Cooking About 50C About 70C USING THE COOKING HOB To start cooking Touch the ON/OFF key for 3 seconds. After power on, the buzzer beeps once, all displays show “...
Page 14
temperature. This can also be used as an energy saving function if using the residual hot cooking zone to heat or warm a pan. Using the Boost function To activate the Boost function, touch the COOKING ZONE SELECT key if there is, touch the relevant cooking zone BOOST key, the POWER LEVEL indicator show “P.”...
Page 15
Touch the “-“ or “+” control of the TIMER CONTROL key once to decrease or increase by 1 minute. Touch and hold the “-“ or “+’ control of the TIMER CONTROL key to decrease of increase by 10 minutes. Touch the “-“ and “+” together, the timer is cancelled and the TIMER SETTING indicator will turn OFF.
Page 16
Hint: Touch “-“ or “+” control of the TIMER CONTROL key once will decrease or increase by 1 minute. Touch and hold “-“ or “+”control of the TIMER CONTROL key will decrease or increase by 10 minutes. When the time is set, it will begin to count down immediately. The TIMER SETTING indicator will show the remaining time and the TIMER SETTING or TIMER indicator will flash for 5 seconds.
Examples of good pan placement and bad pan placement. Good placement Bad placement To activate the Free Zone area as a single cooking zone, simply touch the FREE ZONE key, or touch the corresponding paired COOKING ZONE SELECT keys simultaneously. ...
Page 18
Protection against unintended cooking For ceramic hob, If the electronic control detects a button being held down for approx. 10 seconds, the hob will be switched off automatically. The control sends out an audible error signal to warn the sensors have detected the presence of an object. The display will indicate an error code “ER03” or “ER06"...
A WORD ON CERAMIC COOKING Ceramic cooking is catering for all kinds of cookware, with its radiant heat cooking zones and its electronic touch controls, multi-functions, making it be the ideal choice for the modern family. The use of ceramic cooking is extremely user-friendly, durable and safe. A WORD ON INDUCTION COOKING Induction cooking is a safe, advanced, efficient, and economical cooking technology.
CARE & MAINTENANCE Appliance Cleanliness Avoid rubbing with any abrasive or with the base of the pans, etc. as this will wear the markings on the top of the hob. Clean the surface on a regular basis to prevent the build up of food residue. ...
Page 21
CARE & MAINTENANCE Failure Display and Inspection If an abnormality comes up, the hob will enter the protective state automatically and display corresponding protective codes: Error Possible Cause What to do Message No pot or pot not suitable for the induction Replace the pot.
DISCLAIMER Specifications and designs are subject to change without prior notice. Please refer to www.nodor.kitchen for the most up-to-date version.