Sea-doo SAR 2018 Series Operator's Manual
  1. Manuals
  2. Brands
  3. Sea-doo Manuals
  4. Boat
  5. SAR 2018 Series
  6. Operator's manual

Sea-doo SAR 2018 Series Operator's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
2018
OPERATOR'S
GUIDE
SEA-DOO SAR
®
SERIES
SEARCH AND RESCUE
2 1 9
0 0 1
9 3 9
Original Instructions
Original Instructions

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SAR 2018 Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Sea-doo SAR 2018 Series

Summary of Contents for Sea-doo SAR 2018 Series

  • Page 1 2018 OPERATOR’S GUIDE SEA-DOO SAR ® SERIES SEARCH AND RESCUE 2 1 9 0 0 1 9 3 9 Original Instructions Original Instructions...
  • Page 2 In USA, products are distributed by BRP US Inc. This is a non-exhaustive list of trademarks that are the property of Bombardier Recreational Products Inc. or its affiliates: O.T.A.S. ® Rotax Sea-Doo ® iControl 4-TEC T.O.P.S. 219001939 en SG ®™ and the BRP logo are trademarks of Bombardier Recreational Products Inc. or its affiliates.

  • Page 3: Foreword

    (PWC). It is to ensure backed by the BRP warranty and a net- your new watercraft was prepared to work of authorized Sea-Doo personal your entire satisfaction. watercraft dealers ready to provide the parts, service or accessories you may Know Before you Go require.

  • Page 4: Safety Messages

    FOREWORD To learn how to reduce the risk of be- Keep this Operator's Guide in the wa- ing injured or killed, read the following tercraft as you can refer to it for oper- sections before you operate the water- ation, instructing others, maintenance craft: and troubleshooting.

  • Page 5: Table Of Contents

    TABLE OF CONTENTS FOREWORD ................1 Know Before you Go .
  • Page 6 TABLE OF CONTENTS CONTROLS (cont’d) 2) Engine START/STOP Button..........40 3) Engine Cut-Off Switch .
  • Page 7 TABLE OF CONTENTS OPERATING INSTRUCTIONS (cont’d) General Operating Recommendations........74 OPERATING MODES .
  • Page 8 Beeper Code Information ........... . 130 WARRANTY BRP LIMITED WARRANTY – USA AND CANADA: 2018 SEA-DOO ®...

  • Page 9: Safety Information

    SAFETY INFORMATION ________ ________ SAFETY INFORMATION...

  • Page 10: General Precautions

    GENERAL PRECAUTIONS Avoid Carbon Monoxide flame many feet away from the en- gine. To reduce the risk of fire or explo- Poisoning sion, follow these instructions: All engine exhaust contains carbon – Use only an approved red gasoline monoxide, a deadly gas. Breathing car- container to store fuel.

  • Page 11: Special Safety Messages

    SPECIAL SAFETY MESSAGES Reminders Regarding Safe WARNING Operation Stopping distance will vary de- pending on initial speed, load, The performance of this watercraft wind, number of riders and water may significantly exceed that of other conditions. The amount of braking watercraft you may have operated.
  • Page 12 SPECIAL SAFETY MESSAGES braking effect on the rearward motion. as when docked, or when rafting. Be Also note that your engine must be aware of the risk of CO emanations running to be able to use the brake. from exhaust of other PWCs. When exposed to hazardous situa- Know the waters in which the water- tions such as strong current, tides,...
  • Page 13 Read and understand all safety labels on a handhold before starting the wa- tercraft, and at all times when the wa- on the Sea-Doo PWC, the Operator's tercraft is in motion. All passenger(s) Guide, all other safety documents be- fore operating the PWC.

  • Page 14: Hypothermia

    SPECIAL SAFETY MESSAGES waist of the person in front of them. On a PWC, never place your feet and When going over waves, passenger(s) legs in the water to aid turning. may raise their body slightly off the seat to absorb the shocks with their Drugs and Alcohol legs.

  • Page 15: Safe Boating Courses

    SPECIAL SAFETY MESSAGES Safe Boating Courses Many countries recommend or require a boating safety course. Check with your local competent authorities. Check local and federal boating laws applicable to the waterways where you intend to use your watercraft. Learn the local navigation rules. Know and understand the applicable naviga- tion system (such as buoys and signs).

  • Page 16: Active Technologies (Icontrol)

    ACTIVE TECHNOLOGIES (iCONTROL) Introduction – Cruise mode – Slow speed mode iControl (intelligent Control sys- The O.T.A.S. (Off Throttle Assisted tems) provides environment Steering) is also controlled by the iTC. whereby the operator can control many systems without taking his Sport Mode hands off the handlebars.

  • Page 17: Ibr (Intelligent Brake And Reverse System)

    ACTIVE TECHNOLOGIES (iCONTROL) As you proceed under a constant cruis- – Neutral ing speed setting, hold the throttle – Braking. lever fully depressed in order to keep The operator commands the position your full attention to maintaining good of the iBR gate using either the throttle situational awareness.
  • Page 18 ACTIVE TECHNOLOGIES (iCONTROL) WARNING – It is important to inform the operator of a watercraft who intends to follow in a convoy formation, of the braking and maneuvering capability of your PWC, what the plume of water indicates, and that a greater dis- tance must be maintained be- tween watercraft.

  • Page 19: Safety Equipment

    SAFETY EQUIPMENT Required Safety – Dry suit (in cold weather/water oper- ations) Equipment – Footwear, gloves, safety goggles The operator and the passenger(s) or shatterproof glasses are also rec- must wear an approved Personal Flota- ommended. Some type of light- tion Device (PDF) that is suitable for weight, flexible foot protection is PWC use.
  • Page 20 SAFETY EQUIPMENT and age should be considered when selecting a PFD. The buoyancy pro- vided by the PFD should support your weight in water. The size of the PFD should be appropriate for the wearer. Body weight and chest size are com- mon methods used to size PFDs.
  • Page 21 SAFETY EQUIPMENT Weighing the Risks vs Benefits In order to decide whether or not you should wear a helmet, it is best to con- sider the particular environment you will be riding in, as well as other fac- tors such as personal experience. Will there be a lot of traffic on the water? What is your riding style? The Bottom Line...

  • Page 22: Practice Exercises

    PRACTICE EXERCISES It is always a good idea to practice and Avoiding an Obstacle get familiar with all controls, functions Practice obstacle avoidance (choose a and handling characteristics of this wa- virtual point on the water) by steering tercraft before venturing on the water. the watercraft and maintaining throt- Always secure the tether cord to the tle.

  • Page 23: Important Factors Not To Neglect

    PRACTICE EXERCISES Important Factors Not to Neglect In addition, always remember that the following conditions have a direct im- pact on how this watercraft will behave and respond to different inputs: – Loads – Currents – Wind – Water conditions. Make sure to be alert to these condi- tions, and adapt accordingly.

  • Page 24: Navigation Rules

    NAVIGATION RULES Operating Rules Operating a watercraft can be com- pared with driving on unmarked high- ways and roads. To prevent collisions or avoid other boaters, a system of op- erating rules must be followed. It’s not only common sense... it’s the law! smo2012-003-200 Generally keep to your right and safely TYPICAL...
  • Page 25 NAVIGATION RULES buoy, or to which channel you can con- misjudge the ability of the watercraft tinue. They may also indicate whether or your own riding skills and strike a you are entering a restricted or con- boat, watercraft or person. trolled area such as a no wake or low This watercraft has the capability of speed zone.

  • Page 26: Fueling

    FUELING Fueling Procedure WARNING Fuel tank may be pressurized, fuel WARNING vapors may be released while re- moving the fuel tank cap. Fuel is flammable and explosive under certain conditions. Always work in a well ventilated area. Do 8. Insert the gas pump spout into the not smoke or allow open flames or filler neck and fill up the fuel tank.

  • Page 27: Fuel Requirements

    FUELING Fuel Requirements Use of fuel labeled E15 is prohibited by U.S. EPA Regulations. NOTICE Always use fresh gaso- line. Gasoline will oxidize; the re- sult is loss of octane, volatile com- pounds, and the production of gum and varnish deposits which can damage the fuel system.

  • Page 28: Trailering Information

    A Sea-Doo cover can protect the wa- WARNING tercraft, particularly when driving on dirt roads, to prevent dirt entry through Never tip this watercraft on end for the air inlet openings.

  • Page 29: Important On-Product Labels

    The labels illustrated on the following pages are on your watercraft. If missing or damaged, they can be replaced free of charge. See an authorized Sea-Doo dealer. Please read the following labels carefully before operating this watercraft. NOTE: The first illustration of the watercraft indicates the approximate locations of the various labels.
  • Page 30 IMPORTANT ON-PRODUCT LABELS 219904636 LABEL 1 - MAIN WARNING LH 219903448B LABEL 2 - MAIN WARNING RH F18L0NY LABEL 4 219903184 LABEL 3 _______ ________ SAFETY INFORMATION...
  • Page 31 IMPORTANT ON-PRODUCT LABELS Certain components in the engine compartment may be very hot. Direct contact may result in skin burn. 219903132A 219903132 219904639 LABEL 5 LABEL 7 219904640 F00A2TY LABEL 8 LABEL 6 219904254 LABEL 9 smo2009-002-111_a LABEL 12 smo2009-002-109_a LABEL 10 smo2009-002-106_aen LABEL 13...
  • Page 32 IMPORTANT ON-PRODUCT LABELS 219903502 LABEL 14 219903501 LABEL 15 _______ ________ SAFETY INFORMATION...

  • Page 33: Product Information Labels

    IMPORTANT ON-PRODUCT LABELS Product Information Labels smo2014-008-001_k 219903177 LABEL 1 NOTICE 219904634 LABEL 3 (from 1-1/2 to 2 minutes) 219904387 LABEL 2 ________ ________ SAFETY INFORMATION...

  • Page 34: Compliance Labels

    IMPORTANT ON-PRODUCT LABELS Compliance Labels smo2014-008-001_l COMPLIANCE LABEL LOCATION EMISSION CONTROL INFORMATION THIS ENGINE IS CERTIFIED TO OPERATE ON UNLEADED GASOLINE AND CONFORMS TO U.S. EPA & CALIFORNIA EMISSION / EVAP REGULATIONS FOR MARINE SI ENGINES. ENGINE FAMILY FAMILLE DE MOTEUR LIMITE DES ÉMISSIONS DE LA FAMILLE ENGINE DISPLACEMENT...
  • Page 35 IMPORTANT ON-PRODUCT LABELS 219902637 LABEL 5 - TYPICAL (WATERCRAFT OUTSIDE NORTH AMERICA EXCEPT AUSTRALIA) XXXXXXXXX 219903510 MAXIMUM CAPACITIES LABEL 6 - TYPICAL CAN ICES-2 ABOVE INFORMATION ALSO / NMB-2” U.S.A. APPLIES IN THE EN-FR-219904650-DEC_a LABEL 3 - TYPICAL - CANADIAN COMPLIANCE NOTICE (CAN/US MODELS ONLY) AUSTRALIAN BUILDERS PLATE...

  • Page 36: Pre-Ride Inspection

    WARNING Perform a pre-ride inspection before each ride to detect potential problems during operation.. Correct any problems that you discover to reduce the risk of a breakdown or crash. See an authorized Sea-Doo dealer as neces- sary. CONTROLS Before performing the pre-ride inspection, read and understand the subsection.
  • Page 37 Secure bilge drain plugs. Check throttle lever operation be- fore starting the engine. If any fric- tion is felt in the throttle lever, refer to an authorized Sea-Doo dealer. iBR Lever Check the iBR lever for free and smooth operation. It should return to its initial position immediately after it is released.

  • Page 38: What To Do After Launching The Watercraft

    See your authorized tercraft should move slowly back- Sea-Doo dealer. wards. 4. Release the iBR lever, there should What to Do After not be any reverse thrust.
  • Page 39 PRE-RIDE INSPECTION Variable Trim System With the engine running in forward po- sition, use the VTS system to move the jet pump nozzle up and down alter- nately to check VTS operation. Con- firm the VTS position indicator move- ment in the information center. OPERATING INSTRUCTIONS Refer to subsection for detailed instructions.
  • Page 40 PRE-RIDE INSPECTION This page is intentionally blank _______ ________ SAFETY INFORMATION...

  • Page 41: Watercraft Information

    WATERCRAFT INFORMATION _______________...

  • Page 42: Controls

    CONTROLS NOTE: Some vehicle safety labels are not shown on illustrations. For information WATERCRAFT SAFETY LABELS on vehicle safety labels, refer to subsection. smo2016-001-005_a 1) Handlebar The handlebar controls the direction of the watercraft. During forward opera- tion, turning the handlebar to the right steers the watercraft to the right and inversely.

  • Page 43: Engine Cut-Off Switch

    CONTROLS NOTE: If the START/STOP button is WARNING pressed and held without the tether Should the engine be stopped, the cord installed, the information cen- brake function (models with iBR) ter displays will stay on as long as the and watercraft directional control START/STOP button is held.

  • Page 44: Mode/Set Buttons

    CONTROLS 6) MODE/SET Buttons – Neutral – Braking. These buttons are located on the RH side of the handlebar. NOTE: A minimum of 25% lever travel is required to activate iBR functions. Press MODE button to scroll through various functions available through the information center.

  • Page 45: Cruise Button

    CONTROLS The UP/DOWN buttons are used to It is used to return to SPORT mode make a selection or change a setting after selecting the Touring mode if en- through the information center such gine is not stopped. OPERATING MODES Refer to subsec- –...

  • Page 46: Information Center (Gauges)

    INFORMATION CENTER (GAUGES) WARNING Do not adjust the display while riding, you could lose control. smo2012-001-007_a TYPICAL 1. Multifunction gauge 2. Analog speedometer 3. Analog tachometer Multifunction Gauge Features FEATURE DISPLAY Sport mode indicator Touring mode indicator Fuel level indication Hour meter display ECO mode indicator CRUISE mode indicator...

  • Page 47: Multifunction Gauge Description

    INFORMATION CENTER (GAUGES) Multifunction Gauge Description NUMERICAL DISPLAY 1. Numerical display indication 2. Unit of measurement of indication 15 14 7 smo2011-003-022_a 1) Multifunction Display The multifunction display is used to: – Display the WELCOME message on power up – Provide various indications as se- lected by the operator –...
  • Page 48 (distance and time to empty) Lap timer Top speed/RPM Average speed/RPM X = An X indicates a standard feature - = See your Sea-Doo dealer for availability. OPERATING MODES When the information center is first Refer to subsec- powered up, the numerical display de- tion for detailed instructions.
  • Page 49 INFORMATION CENTER (GAUGES) 5) Fuel Level Indication A bar gauge located in the bottom RH side of the multifunction display con- tinuously indicates the amount of fuel in the fuel tank while riding. HOUR METER DISPLAY 7) Water Depth Display NOTE: This feature is not available on the SAR.
  • Page 50 CHECK ENGINE LIGHT When the check engine light comes on, you may seek service from an au- thorized Sea-Doo dealer, repair shop, or person of your own choosing for HIGH TEMPERATURE INDICATOR maintenance, repair, or replacement. US EPA EMIS-...
  • Page 51 INFORMATION CENTER (GAUGES) ECO MODE INDICATOR iBR POSITION INDICATOR (Fuel Economy Mode) 15) SKI MODE Indicator OPERATING MODES Refer to subsec- The ski mode indicator is not active on tion for detailed instructions. the SAR model. 13) CRUISE Mode Indicator The cruise mode indicator comes ON when: –...

  • Page 52: Navigating The Multifunction Display

    INFORMATION CENTER (GAUGES) Navigating the Function Description Multifunction Display Compass A GPS incorporated in the information WARNING center provides the indication in the Do not adjust display while riding, multifunction display. you could lose control. The cardinal points, intermediate car- dinal points, as well as the azimuth the Selecting Functions watercraft is travelling are displayed...
  • Page 53 INFORMATION CENTER (GAUGES) MESSAGE DISPLAYED LAP TIMER FUNCTION EXAMPLE LAP TIME 1. 01'02'34 lap time displayed here 2. Lap number "1" displayed here 2. Press the SET button to enter the function, the lap timer will be acti- 5. To save the last lap and stop the vated and visible in the display.
  • Page 54 INFORMATION CENTER (GAUGES) To display the watercraft fuel con- sumption, carry out the following: 1. Press the MODE button repeatedly until FUEL CONSUMPTION is visi- ble in the multifunction display. LAP TIMER FUNCTION EXAMPLE 1. Total lap times 02'23'37 displayed here 2.

  • Page 55: Changing Numerical Display Indication

    INFORMATION CENTER (GAUGES) VTS Mode 3. Press the UP/DOWN button until the preferred indication is visible in The VTS MODE function is used to the multifunction display (as appli- manually set the VTS or change VTS cable to model). PRESET settings. –...

  • Page 56: Multifunction Gauge Setup

    To change the units of measurement or to change the language displayed in the multifunction gauge, see your authorized Sea-Doo dealer. FUNCTION SELECTED - CLOCK Analog Speedometer 1. CLOCK indication Description 2.

  • Page 57: Analog Tachometer Description

    INFORMATION CENTER (GAUGES) If for some reason the GPS signal is lost, a default mode is used whereby, the speed is calculated using infor- mation received from other systems to provide an estimated watercraft speed. Analog Tachometer Description The tachometer provides an analog in- dication of the revolutions per minute (RPM) of the engine.

  • Page 58: Equipment

    EQUIPMENT NOTE: Some vehicle safety labels are not shown on illustrations. For information WATERCRAFT SAFETY LABELS on vehicle safety labels, refer to subsection. smo2014-008-001_d TYPICAL - MODEL WITH NAVIGATION LIGHTS AND INFLATABLE SPONSON SHOWN 1) Glove Box 2) Front Storage Compartment A small, storage compartment for per- sonal articles.

  • Page 59: Seat

    EQUIPMENT To remove the seat, pull up on the latch handle and lift the back end of the seat off the latch pin. Then pull the seat up and backwards to unhook the front of the seat from it's retainer and remove the seat from the watercraft.

  • Page 60: Passenger Handhold

    EQUIPMENT 4) Passenger Handhold The seat strap provides a handhold for a passenger to hold on to when riding. The sides of the molded grab handle at the rear of the seat also provide a hand- hold for a passenger. The rear portion of the molded grab handle provides a handhold for the spotter or boarding the watercraft from the water.

  • Page 61: Eyelets

    EQUIPMENT smo2009-002-133 smo2008-001-020_a TYPICAL - BOARDING STEP HELD DOWN TYPICAL FOR BOARDING FROM WATER 1. Front eyelet NOTICE Transom Eyelets – Never use the step for boarding a watercraft that is out of water. The transom eyelets can be used for: –...

  • Page 62: Bilge Drain Plugs

    EQUIPMENT CAUTION Never attach to the mast to pull a load. This can cause damage to the mast and/or water- craft. smo2014-008-003_a TYPICAL 1. Central eyelet smo2014-008-001_g 1. Rear mast NOTICE Do not use the central eyelet for towing. Use only for at- 10) Navigation Lights taching a rescue sled.

  • Page 63: Ropes

    EQUIPMENT smo2014-008-001_h smo2014-008-001_j 1. Sponson (on each side) 1. Running board (on each side) NOTICE Sponsons must be in- 14) Heavy-Duty Front flated to correct pressure at all times. Bumper MAINTENANCE Refer to section. The heavy duty front bumper protects 12) Ropes the front end of the watercraft.

  • Page 64: Break-In Period

    BREAK-IN PERIOD Operation During Break-In Period A break-in period of 10 operating hours is required before running the water- craft at sustained full throttle. During this period, maximum throttle should not exceed 1/2 to 3/4 opening. However, brief full acceleration and speed variations contribute to a good break-in.

  • Page 65: Operating Instructions

    Should any control or instruction not be F18A01Y fully understood, refer to an authorized Sea-Doo dealer. TYPICAL Boarding from Water Boarding the Watercraft The ideal water depth to board the As with any watercraft, boarding watercraft is 90 cm (3 ft).
  • Page 66 OPERATING INSTRUCTIONS NOTICE NOTICE In shallow water, keep speed to a minimum and avoid hard – Stay on center of the step. accelerations. Even though this wa- – Only one person at a time on the tercraft is equipped with an anti-de- step.

  • Page 67: How To Start Engine

    OPERATING INSTRUCTIONS Take hold of the seat strap to help main- tain your balance and step forward onto the footboards on either side of the seat. smo2009-002-149 TYPICAL smo2009-002-145 TYPICAL Sit astride the seat. Operator with a Passenger The operator climbs on the watercraft smo2009-002-150 in the same way as explained previ- TYPICAL...

  • Page 68: How To Stop The Engine

    OPERATING INSTRUCTIONS How to Stop the Engine WARNING In shallow water, debris may be WARNING picked up and thrown rearward by the jet pump onto people or prop- To maintain watercraft directional erty. control, the engine should be running until the watercraft is stopped.

  • Page 69: How To Engage Neutral

    OPERATING INSTRUCTIONS O.T.A.S. System WARNING (Off-Throttle Assisted Steering) Throttle should be applied and The O.T.A.S. (Off-Throttle Assisted handlebar turned to change the di- Steering) system provides additional rection of the watercraft. Steering maneuverability in off-throttle situa- efficiency will differ depending on tions.

  • Page 70: How To Engage Forward

    OPERATING INSTRUCTIONS How to Engage and Use If the watercraft is moving backwards, momentarily press the UP button. Reverse Reverse can only be engaged between idle speed and the threshold forward speed of 8 km/h (5 MPH). To engage reverse position, the iBR lever on the LH handlebar must be pulled in at least 25% of the lever travel.

  • Page 71: How To Engage And Use Braking

    OPERATING INSTRUCTIONS Available engine power is limited in CAUTION Steering direction reverse mode, which limits reverse in reverse is opposite of forward. speed. To steer the stern to port (left) in re- verse, turn the handlebar to star- WARNING board (right). To steer the stern to starboard (right), turn the handle- Only use reverse at slow speed bar to port (left).
  • Page 72 OPERATING INSTRUCTIONS WARNING CAUTION As the watercraft slows to a stop, the wake created Braking should be practiced in by the watercraft will catch up and open waters and at gradually in- tend to push the watercraft forward. creasing speeds in order to be- Ensure there are no obstacles or come fully familiar with the con- bathers in the direction of travel.

  • Page 73: How To Use The Variable Trim System (Vts)

    OPERATING INSTRUCTIONS When the nozzle is positioned in an CAUTION As the watercraft upward angle, the water jet directs the slows to a stop while braking in a bow of the watercraft upward. This po- turn, the wake created by the water- sition is used to optimize high speed.
  • Page 74 OPERATING INSTRUCTIONS With the watercraft operating in for- To select the highest trim position ward position, proceed as follows: recorded, double-click on the VTS UP button (bow up). 1. Press the VTS UP button once to trim the bow of the watercraft up to To select the lowest trim position the next trim position.
  • Page 75 OPERATING INSTRUCTIONS 6. Press the SET button to save PRE- SET 1 and display PRESET 2. 7. Press the VTS UP/DOWN button to change the PRESET 2 VTS position. Gauge will display setting 1 through 5 in the digital screen above PRE- SET 2.

  • Page 76: General Operating Recommendations

    OPERATING INSTRUCTIONS 4. Press the SET button to save the de- – Water intake grate sired setting and return to the main – Impeller display. – Wear ring. NOTE: The available VTS settings are between 1 and 5. WARNING NOTE: The VTS system cannot be In shallow water, debris may be fully tested without the engine operat- picked up and thrown rearward by...
  • Page 77 OPERATING INSTRUCTIONS WARNING It is important to inform the oper- ator of a watercraft who intends to follow in a convoy formation of the braking and maneuvering capabil- ity of your PWC, what the plume of water indicates, and that a greater distance should be maintained be- tween both of you.
  • Page 78 OPERATING INSTRUCTIONS NOTICE Even though this water- craft is equipped with an anti-debris water intake grate, it is still possi- ble that debris such as rocks, sand or other objects may damage the propulsion system in shallower wa- ter than 90 cm (3 ft). The hull protec- tion coating may not prevent dam- ages to the hull caused by collisions with obstacles.

  • Page 79: Operating Modes

    OPERATING MODES AVAILABLE OPERATING MODES Sport mode Touring mode ECO mode Cruise mode Slow speed mode X = Indicates a standard feature Opt = Indicates a feature available as an option N.A. = Not Applicable Sport Mode By default, the watercraft is in SPORT mode of operation when first started.

  • Page 80: Eco Mode (Fuel Economy Mode)

    OPERATING MODES Deactivating Touring Mode To deactivate Touring mode while rid- ing at speed, carry out the following: WARNING When deactivating touring mode, be sure to maintain situational awareness of other watercraft, ob- stacles, or persons in the water. MESSAGE DISPLAYED ECO MODE 1.

  • Page 81: Cruise Mode

    OPERATING MODES Cruise Mode 2. Press and hold the cruise button. Cruise mode is a function of iTC (in- telligent Throttle Control) system that allows the operator to set the desired maximum watercraft speed. This is useful when cruising for long distances, operating in limited speed zones or for towing.
  • Page 82 OPERATING MODES The following will be displayed in the multifunction gauge. CRUISE MODE INDICATOR Cruise Mode Activation Above Idle FUNCTION SELECTED - CRUISE Speed MODE To activate cruise mode above idle 1. CRUISE MODE _ SPEED speed (10 km/h (6 MPH)): ADJUSTING 1.

  • Page 83: Slow Speed Mode

    OPERATING MODES CRUISE MODE INDICATOR FUNCTION SELECTED - CRUISE MODE Changing Set Cruise Speed 1. CRUISE MODE _ SPEED To increase or decrease the set cruise ADJUSTING speed: 2. Cruise speed set point indication 1. Hold the throttle lever all the way in to the handlebar.
  • Page 84 OPERATING MODES The operator can select an idle speed set point (slow speed) be- tween 1 and 5 (1.6 km/h to 11 km/h (1 MPH to 7 MPH)). If you accelerate above approximately 14 km/h (9 MPH), Slow Speed Mode will be deactivated and the engine will return to its normal idle RPM when the throttle is released.
  • Page 85 OPERATING MODES sdd2009-001-024_i MESSAGE DISPLAYED TYPICAL SLOW SPEED MODE ACTIVE 1. UP button to increase speed 2. DOWN button to decrease speed Deactivating Slow Speed Mode While the UP/DOWN is being pressed to change the slow speed set point, Slow speed mode can be deactivated the following will appear in the multi- using any of the following methods: function gauge.

  • Page 86: Special Procedures

    SPECIAL PROCEDURES Jet Pump Water Intake and If the aforementioned method does not work, the following can be per- Impeller Cleaning formed: – With engine running and before ap- WARNING plying throttle, pull the iBR lever in Keep away from intake grate while to select reverse operation and vary engine is running.
  • Page 87 SPECIAL PROCEDURES WARNING If it is necessary to reach in to re- move any foreign object caught in the propulsion system, strictly observe the following before pro- ceeding: – Remove tether cord from the engine cut-off switch. – Wait at least 5 minutes. AVAILABLE MODE FUNCTION –...

  • Page 88: Capsized Watercraft

    SPECIAL PROCEDURES Capsized Watercraft NOTE: Use the UP/DOWN button on the RH handlebar to move the iBR to The watercraft is designed so that it the desired position once the iBR over- should not turn over easily. Two inflat- ride function has been activated as able sponsons mounted on the side of described in the previous steps.

  • Page 89: Submerged Watercraft

    Bring the watercraft to an authorized NOTICE If the watercraft has been Sea-Doo dealer as soon as possible to capsized for more than 5 minutes, have it serviced. do not attempt to crank the engine...
  • Page 90 SPECIAL PROCEDURES smo2013-001-001_a 1. Cross over hose ______________...

  • Page 91: Maintenance Information

    MAINTENANCE INFORMATION _______________...

  • Page 92: Maintenance Schedule

    Sea-Doo dealer has an in-depth technical knowledge and tools to service the Sea-Doo personal watercraft, the emission-related warranty is not condi- tioned on the use of an authorized Sea-Doo dealer or any other establishment with which BRP has a commercial relationship. For emission-related warranty...
  • Page 93 MAINTENANCE SCHEDULE A: ADJUST FIRST 50 HOURS OR 1 YEAR C: CLEAN EVERY 100 HOURS OR 1 YEAR I: INSPECT L: LUBRICATE EVERY 200 HOURS OR 2 YEARS R: REPLACE O: OPERATOR TO BE PERFORMED BY RS: REPAIR SHOP PART/TASK NOTE ENGINE Engine oil and filter...
  • Page 94 MAINTENANCE SCHEDULE A: ADJUST FIRST 50 HOURS OR 1 YEAR C: CLEAN EVERY 100 HOURS OR 1 YEAR I: INSPECT L: LUBRICATE EVERY 200 HOURS OR 2 YEARS R: REPLACE O: OPERATOR TO BE PERFORMED BY RS: REPAIR SHOP PART/TASK NOTE ELECTRICAL SYSTEM Spark plugs...
  • Page 95 MAINTENANCE SCHEDULE A: ADJUST FIRST 50 HOURS OR 1 YEAR C: CLEAN EVERY 100 HOURS OR 1 YEAR I: INSPECT L: LUBRICATE EVERY 200 HOURS OR 2 YEARS R: REPLACE O: OPERATOR TO BE PERFORMED BY RS: REPAIR SHOP PART/TASK NOTE iBR SYSTEM (intelligent Brake and Reverse) iBR lever...

  • Page 96: Maintenance Procedures

    You Turn off the engine and follow should seek service from an autho- these maintenance procedures rized Sea-Doo dealer, repair shop, when performing maintenance. or person of your own choosing If you do not follow proper main-...
  • Page 97 MAINTENANCE PROCEDURES Engine Oil Level NOTICE Check level frequently and refill if necessary. Do not over- fill. Operating the engine with an improper level may severely dam- age engine. CAUTION Certain compo- nents in the engine compartment may be very hot. Direct contact may smo2011-003-010_a result in skin burn.

  • Page 98: Engine Coolant

    9. Properly reinstall oil cap and dip- stick. Engine Oil Change and Oil Filter Replacement The oil change and filter replacement may be performed by an authorized Sea-Doo dealer, repair shop, or person smo2011-003-010_c of your own choosing. TYPICAL 1. Expansion tank cap Engine Coolant...

  • Page 99: Ignition Coils

    See an authorized Sea-Doo dealer. Engine Coolant Replacement Coolant replacement should be per- formed by an authorized Sea-Doo dealer. Ignition Coils Ignition Coil Removal sbs2009-011-001_a 1. Open seat.

  • Page 100: Spark Plugs

    MAINTENANCE PROCEDURES 5. Apply DOW CORNING 111 (P/N 413 WARNING 707 000) or an equivalent on rubber Never remove an ignition coil from seal contact area. a spark plug without disconnect- ing it from the wiring harness. Flammable vapors may be present in the bilge.

  • Page 101: Exhaust System And Heat Exchanger

    MAINTENANCE PROCEDURES Spark Plug Installation Flushing should be performed when the watercraft is not expected to be Prior to installation, ensure the contact used further the same day or when the surfaces of the cylinder head and spark watercraft is stored for any extended plug are free of grime.

  • Page 102: Ride Plate And Water Intake Grate

    To flush, start engine then immediately of water and damage the propulsion open the water tap. system. Clean as necessary. If any ob- struction cannot be removed, refer to an authorized Sea-Doo dealer for ser- CAUTION Certain compo- vicing. nents in the engine compartment may be very hot.

  • Page 103: Sacrificial Anode

    Fuse Removal and Installation Inspect ride plate and jet pump wa- ter intake grate for damage. See your Use the fuse remover/installer in- Sea-Doo dealer to have any damaged cluded in the fuse box to ease fuse part repaired or replaced. removal.
  • Page 104 MAINTENANCE PROCEDURES ahead of the fuel tank just under the gauge area, attached to the battery holder. smo2011-003-011_c BATTERY AND FUSE ACCESS, FRONT STORAGE COMPARTMENT 1. Battery access panel smo2014-008-011_a TYPICAL 1. Fuse box 2. Fuel tank 3. Front storage compartment (access panel removed) To remove the fuse box cover, squeeze and hold locking tabs on both sides of...
  • Page 105 MAINTENANCE PROCEDURES Fuse Box 1 Description FUSE RATING DESCRIPTION — Not used 15 A Diagnostic connector START/STOP button 30 A 30 A Charge — Not used 30 A Battery — Not used — Not used Depth sounder (if so equipped) Gauge, O.T.A.S.

  • Page 106: Inflatable Sponsons

    MAINTENANCE PROCEDURES Inflatable Sponsons Important Information on Sponson Inflation The sponsons must be inflated to the recommended pressure at all times SPONSON PRESSURE MINIMUM MAXIMUM 28 kPa (4 PSI) 41 kPa (6 PSI) F03L16Y It is normal to observe changes in air TYPICAL 1.
  • Page 107 MAINTENANCE PROCEDURES Inflate sponson to specification. Verify pressure using the valve adapter and a low pressure gauge (70 kPa (10 PSI)). NOTE: Seat valve adapter as quickly as possible onto valve opening and firmly maintain in position to avoid air loss.
  • Page 108 MAINTENANCE PROCEDURES Tear Repair of Less than 5 cm (2 in) Tear Repair of More than 5 cm (2 in) Deflate completely sponson to be re- Deflate completely sponson to be re- paired. paired. Cut a patch about 75 mm (3 in) larger Cut 2 patches about 75 mm (3 in) larger than the tear in every direction.
  • Page 109 MAINTENANCE PROCEDURES Repeat the same bonding procedure for the outer patch. Allow 24 hours to dry before inflating. Clean any glue excess. ______________...

  • Page 110: Watercraft Care

    WATERCRAFT CARE Remove the watercraft from the water marine organisms from engine and/or every day. hull. Apply non-abrasive wax such as silicone wax. Post-Operation Care NOTICE Never clean fiberglass and plastic parts with strong deter- Exhaust System and Heat gent, degreasing agent, paint thin- Exchanger Flushing ner, acetone, or other strong chemi- The exhaust system and the heat ex-...

  • Page 111: Post-Operation Inspection

    Correct any problems that you discover to reduce the risk of a breakdown for the next outing. See an authorized Sea-Doo dealer as necessary. WARNING Engine should be off and the tether cord cap should always be removed from the engine cut-off switch prior to verifying any of the following points.
  • Page 112 WATERCRAFT CARE ✓ ITEM OPERATION Check condition of sponsons and running boards. Also: Inflatable sponsons including running boards – Inspect cords. – Inspect and tighten shackles. Check condition: – Make sure mast is properly installed and check for any play. Tighten nuts if required.

  • Page 113: Storage And Preseason Preparation

    It is recommended that the watercraft condition. Fuel stabilizer should be serviced by an authorized Sea-Doo be added prior to engine lubrica- dealer, repair shop, or person of your tion and fuel tank top up to ensure...
  • Page 114 Electrical System NOTICE Failure to drain the ex- haust system may cause severe Battery Removal and Charging damage to the exhaust manifold. Contact your authorized Sea-Doo Remove special tools. dealer. Engine Internal Lubrication WARNING 1. Open the seat. Never charge or boost (jump start) 2.

  • Page 115: Preseason Preparation

    Preseason maintenance preparation ner, acetone, or other strong chemi- may be performed by an authorized cal or petroleum cleaners. Sea-Doo dealer, repair shop or person of your own choosing. Body and Hull Repair NOTE: Though not required, it is If any repairs are needed to body com-...
  • Page 116 STORAGE AND PRESEASON PREPARATION This page is intentionally blank ______________...

  • Page 117: Technical Information

    TECHNICAL INFORMATION ______________...

  • Page 118: Watercraft Identification

    WATERCRAFT IDENTIFICATION The main components of the water- craft (engine and hull) are identified by different serial numbers. It may some- times become necessary to locate these numbers for warranty purposes or to trace the watercraft in the event of theft. Hull Identification Number The Hull Identification Number (HIN) is located on the boarding platform at the...

  • Page 119: Engine Emissions Information

    ENGINE EMISSIONS INFORMATION Manufacturer's EPA Emission Regulations Responsibility All 1999 and more recent Sea-Doo watercraft manufactured by BRP are Beginning with 1999 model year en- certified to the EPA as conforming to gines, PWC manufacturers of marine the requirements of the regulations for...

  • Page 120: Specifications

    SPECIFICATIONS SEA-DOO SAR ENGINE ® ® Rotax 1503 4-TEC . Single Over Type Head Camshaft (SOHC) Declared Power 106 kW @ 7300 RPM Induction Naturally-aspirated Number of cylinders 12 valves (4 per cylinder) with Number of valves hydraulic lifters (no adjustment) Displacement 1 494 cm³...
  • Page 121 SPECIFICATIONS SEA-DOO SAR PROPULSION (con't) Type Electronic, gauge interface DIMENSIONS Length 339 cm (133.4 in) Width 170 cm (66.8 in) Height (except rear mast) 111.8 cm (44 in) WEIGHT AND LOADING CAPACITY Weight (dry) 438 kg (965 lb) Rider capacity...
  • Page 122 SPECIFICATIONS This page is intentionally blank ______________...

  • Page 123: Troubleshooting

    TROUBLESHOOTING ______________...

  • Page 124: Troubleshooting Guidelines

    – Refer to WATER-FLOODED ENGINE in SPECIAL PROCEDURES. 6. Faulty sensor or ECM. – Seek service from an authorized Sea-Doo dealer, repair shop, or person of your own choosing for maintenance, repair, or replacement. Please refer to the US EPA EMISSIONS-RELATED WARRANTY contained herein for information about warranty claims.
  • Page 125 5. Engine management system fault detected (check engine pilot lamp is ON). – Seek service from an authorized Sea-Doo dealer, repair shop, or person of your own choosing for maintenance, repair, or replacement. Please refer to the US EPA EMISSIONS-RELATED WARRANTY contained herein for information about warranty claims.
  • Page 126 TROUBLESHOOTING GUIDELINES ENGINE SMOKE (cont’d) 3. Internal engine damage. – Seek service from an authorized Sea-Doo dealer, repair shop, or person of your own choosing for maintenance, repair, or replacement. Please refer to the US EPA EMISSIONS-RELATED WARRANTY contained herein for information about warranty claims.
  • Page 127 – Release the throttle to idle RPM. – Press the CRUISE button to activate the slow speed mode. – Return to shore using the slow speed mode. Refer to an authorized Sea-Doo dealer. iBR WILL NOT RETURN TO NEUTRAL POSITION (IBR INDICATOR LIGHT ON) 1.
  • Page 128 1. Bilge pump malfunction. – Refer to an authorized Sea-Doo dealer. 2. Bailer system malfunction. – Have system inspected by an authorized Sea-Doo dealer. 3. Exhaust system leak. – Refer to an authorized Sea-Doo dealer. 4. Carbon ring at drive shaft worn.

  • Page 129: Monitoring System

    When a fault occurs, it sends Sea-Doo dealer to pass on the fault visual messages through the infor- code. The dealer will then advise the mation center and/or audible signals...

  • Page 130: Fault Indicators And Message Display Information

    If a fault indicator or a fault message comes ON in the multifunction gauge, seek service from an authorized Sea-Doo dealer, repair shop, or person of your own choosing for maintenance, repair, or replacement. Please refer to the...
  • Page 131 MONITORING SYSTEM MESSAGE DISPLAY INFORMATION RIGHT KEYPAD ERROR Gauge control button malfunction LOW OIL PRESSURE Engine low oil pressure detected HIGH EXHAUST TEMPERATURE High exhaust temperature detected HIGH TEMPERATURE High engine temperature detected Engine system malfunction or CHECK ENGINE maintenance required HIGH BATTERY VOLTAGE High battery voltage detected LOW BATTERY VOLTAGE...

  • Page 132: Beeper Code Information

    Improper operation of ECM or defective wiring 1 long beep harness. (when installing tether Seek service from an authorized Sea-Doo dealer, repair cord on engine cut-off shop, or person of your own choosing for maintenance, switch) repair, or replacement. Please refer to the US EPA...
  • Page 133 WARRANTY ______________...

  • Page 134: Brp Limited Warranty - Usa And Canada: 2018 Sea-Doo

    This limited warranty will become null and void if: (1) the Sea-Doo personal watercraft was used for racing or any other competitive activity, at any point, even by a pre- vious owner;...
  • Page 135 RELATED WARRANTY contained herein. 4. For Sea-Doo personal watercrafts produced by BRP for sale in the State of Cali- fornia or New York that are originally sold to a resident or subsequently warranty registered to a resident in the State of California or New York, please also refer to the applicable California and New York Emissions Control Warranty Statement contained herein.
  • Page 136 BRP dealer during the applicable warranty coverage period under the conditions described herein. No claim of breach of warranty shall be the cause for cancellation or rescission of the sale of the Sea-Doo personal watercraft to the owner. In the event that service is required outside of the country of original sale, the...
  • Page 137 We recommend discussing the issue with the authorized BRP dealer’s service manager or owner. If the issue has not yet been resolved, please contact us: http://www.sea-doo.com/form/contact-us.html Tel.: 1-888-272-9222 * In the USA, products are distributed and serviced by BRP US Inc.

  • Page 138: Us Epa Emission-Related Warranty

    BRP. For all emission-related warranty claims, BRP is limiting the diagnosis and repair of emission-related parts to the authorized Sea-Doo dealers, unless for emergency repairs as required by item 2 of the following list.
  • Page 139 Components Covered The emission-related warranty covers all components whose failure would in- crease an engine’s emissions of any regulated pollutant, including the following listed components: 1. For exhaust emissions, emission-related components include any engine parts related to the following systems: –...
  • Page 140 Limited Applicability As a certifying manufacturer, BRP may deny emission-related warranty claims for failures that have been caused by the owner’s or operator’s improper main- tenance or use, by accidents for which the manufacturer has no responsibility, or by acts of God. For example, an emission-related warranty claim need not be honored for failures that have been directly caused by the operator’s abuse of the engine/equipment or the operator’s use of the engine/equipment in a manner for which it was not designed and are not attributable to the manufacturer in any way.

  • Page 141: California And New York Emission Control Warranty

    ® PERSONAL WATERCRAFT For California and New York, your 2018 Sea-Doo personal watercraft has a special environmental label required by the California Air Resources Board. The label has 1, 2, 3 or 4 stars. A hangtag, provided with your personal watercraft, describes the meaning of the star rating system.
  • Page 142 Select emission control parts of your 2018 Sea-Doo personal watercrafts are warranted from the date of delivery to the first retail consumer for a period of 4 years, or for 250 hours of use, whichever occurs first.
  • Page 143 ® Parts covered for a Model Year 2018 Sea-Doo personal watercraft: Idle bypass valve Air intake adapter Throttle position sensor Spark plugs Intake manifold air pressure sensor Ignition coils Intake manifold air temperature sensor Air box Engine temperature sensor Intake and exhaust valve and seals...
  • Page 144 Owner’s Warranty Responsibilities As the owner of a 2018 Sea-Doo personal watercraft, you are responsible for the performance of the required maintenance listed in your Operator’s Guide. BRP recommends that you retain all receipts covering maintenance of your personal watercraft engine, but BRP cannot deny warranty solely for the lack of receipts or your failure to ensure the performance of all scheduled maintenance.

  • Page 145: Brp International Limited Warranty: 2018 Sea-Doo

    All genuine BRP personal watercraft parts and accessories, installed by an autho- rized Sea-Doo Distributor/Dealer at the time of delivery of the 2018 Sea-Doo per- sonal watercraft, carry the same warranty as that of the personal watercraft.
  • Page 146 Sea-Doo Distributor/Dealer; – Damage caused by abuse, misuse, abnormal use, neglect, racing, improper operation or operation of the product in a manner inconsistent with the recom- mended operation described in the Operator’s Guide;...
  • Page 147 This warranty coverage is available only if each of the following conditions has been fulfilled: – The 2018 Sea-Doo personal watercraft must be purchased as new and unused by its first owner from a Sea-Doo Distributor/Dealer authorized to distribute Sea- Doo personal watercrafts in the country in which the sale occurred;...
  • Page 148 No claim of breach of warranty shall be cause for cancellation or rescission of the sale of the Sea-Doo personal watercraft to the owner. You may have other legal rights which may vary from country to country.
  • Page 149 For all other countries, please contact your local Sea-Doo Distributor/Dealer (visit our website at www.brp.com for contact information), or contact our North American office at: BOMBARDIER RECREATIONAL PRODUCTS INC. Consumer Assistance Center 75 J.-A. Bombardier Street Sherbrooke QC J1L 1W3 Tel.: +1 819 566-3366...

  • Page 150: Brp Limited Warranty For The European Economic Area, The Commonwealth Of The Independent States, Turkey: 2018 Sea-Doo Personal Watercraft

    All genuine BRP personal watercraft parts and accessories, installed by an autho- rized Sea-Doo Distributors/Dealers at the time of delivery of the 2018 Sea-Doo per- sonal watercraft carry the same warranty as that of the personal watercraft. This limited warranty will become null and void if: (1) the personal watercraft was used for racing or any other competitive activity, at any point, even by a previous owner;...
  • Page 151 Sea-Doo Distributor/Dealer; – Damage caused by abuse, misuse, abnormal use, neglect, racing, improper operation or operation of the product in a manner inconsistent with the recom- mended operation described in the Operator’s Guide;...
  • Page 152 BRP’s responsibility is limited to making the required repairs or replacements of parts. No claim of breach of warranty shall be cause for cancellation or rescission of the sale of the Sea-Doo personal watercraft to the owner. You may have other legal rights which may vary from country to country.
  • Page 153 9. CONSUMER ASSISTANCE 1. In the event of a controversy or a dispute in connection with this limited warranty, BRP suggests that you try to resolve the issue at the Sea-Doo Distributor/Dealer level. We recommend discussing the issue with the autho- rized Sea-Doo Distributor/Dealer's service manager or owner.
  • Page 154 ADDITIONAL TERMS AND CONDITIONS FOR FRANCE ONLY The following terms and conditions are applicable to products sold in France only: The seller shall deliver goods that are complying with the contract and shall be re- sponsible for defects existing upon delivery. The seller shall also be responsible for defects resulting from packaging, assembling instructions or the installation when it is its responsibility per the contract or if accomplished under its responsibility.

  • Page 155: Customer Information

    CUSTOMER INFORMATION ______________...

  • Page 156: Privacy Information

    PRIVACY INFORMATION BRP wishes to inform you that your coordinates will be used for safety and war- ranty related purposes. Furthermore, BRP and its affiliates may use its customer list to distribute marketing and promotional information about BRP and related products.

  • Page 157: Contact Us

    CONTACT US South America www.brp.com Rua James Clerck Maxwell, 230 North America TechnoPark Campinas SP 13069-380 Brazil 565 de la Montagne Street Valcourt (Québec) J0E 2L0 Asia Canada Sturtevant, Wisconsin, U.S.A. 15/F Parale Mitsui Building,8 10101 Science Drive Higashida-Cho, Kawasaki-ku Sturtevant, Wisconsin Kawasaki 210-0005 53177...

  • Page 158: Change Of Address/Ownership

    CHANGE OF ADDRESS/OWNERSHIP If your address has changed or if you are the new owner of the watercraft, be sure to notify BRP by either: – Mailing one of the following card below; – North America Only: calling at 1-888-272-9222; –...
  • Page 159 CHANGE OF ADDRESS/OWNERSHIP ______________...
  • Page 160 CHANGE OF ADDRESS/OWNERSHIP This page is intentionally blank ______________...
  • Page 161 CHANGE OF ADDRESS/OWNERSHIP NOTES ______________...
  • Page 162 CHANGE OF ADDRESS/OWNERSHIP NOTES ______________...
  • Page 164 219 001 939 OPERATOR’S GUIDE, SEA-DOO SAR SERIES / ENGLISH GUIDE DU CONDUCTEUR, SÉRIE SEA-DOO SAR / ANGLAIS FAIT AU / MADE IN CANADA U/M:P.C ®™ AND THE BRP LOGO ARE TRADEMARKS OF BOMBARDIER RECREATIONAL PRODUCTS INC. OR ITS AFFILIATES.

Table of Contents