Advertisement
INSTALLATION
How to Install the Shower Column
Select a location in vertical wall to install shower column according
to rough-in dimensions.
Drill the lower hole as anchors(1) diameter and lower base(3-1)
10
position in the finished wall(NOTE: The arrow in the base is
upward). Press anchors into the hole, secure the base by the
screws(2).
1
11
3-2
2
7
Rehearse the shower column kit(4) installation for the upper
base(3-2) mounting location determination. Slide the tube joint(5)
onto the shower column kit, and connect them to the base(NOTE:
The arrow in the base is upward). Install the screws(7) into the tube
joint with the hex wrench(6), and tighten them.
5
9
Place the shower column and the body against the finished wall.
4
Connect the lower base and the diverter body kit(8). Position and
tighten them by hex wrench. Mark the hole of upper base(3-2) with
a pencil. Uninstall the shower column kit and tube joint.(NOTE:
6
Don't lose the screws.)
Drill holes on the mark. Press the anchors into the holes. Secure
the upper base(3-2) by the screws. Install the tube joint(5) to the
base(3-2) and tighten them by screws. Reinstall the shower column
kit with escutcheons (9) to the bases. Tighten the screws with the
hex wrench. Screw the escutcheons with the bases until against
7
the finished wall.
9
Install the tube kit(10) into the shower column kit. Install the nut(11)
1
onto the tube kit with soft cloth between internal hole of the nut and
3-1
2
the tube kit. Then screw the nut onto the shower column kit with
16
8
13
strap wrench or soft cloth between the nut and regular wrench.
15
14
13
Connect the hose(12) with washers(13) between the mixer water
supply and the connector(14). The connector(15) will be used for
handshower connection.
12
How to Install the Showerhead
Ensure the diverter handle(16) is in the position for
16
15
showerhead(19), run hot and cold water for about one minute to
remove any debris before the showerhead is installed.
20
17
18
Take out the washer(17) and install the regulator(18) into the
showerhead inlet if needed, then reinstall the washer as shown.
Tighten the showerhead onto the tube kit outlet(20) with strap
wrench.
19
1338589-2A-A
25
16
15
23
Katalyst Air
How to Operate the Hand Shower
Press the buttons of the hand shower to
change the water flow.
INSTALLATION CHECKOUT
Ensure that all connections are tight. Ensure that the handle is in the off position.
Open the drain. Turn on main water supply and check for leaks. Repair as required.
CLEANING INSTRUCTIONS
All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with clean soft
cloth. Many cleaners may contain chemicals, such as ammonia, chlorine, toilet cleaner etc. which could adversely
affect the finish and are not recommended for cleaning.
Do not use abrasive cleaners or solvents on Kohler faucets and fittings.
2
1338589-2A-A
How to Install the Hand Shower
21
Ensure the diverter handle(16) is in the position for hand
shower(21), run hot and cold water for about one minute to remove
any debris before the hand shower is installed.
22
23
Install regulator(22) into the hand shower inlet if needed. Put the
washers(23) in each end of the hose(24). Connect the hand
shower and the connector(15) with hose.
24
Hang the hand shower into the shower bracket(25).
Intense Massage
How to Maintain the Hand Shower
Any debris or mineral build-up may cause the flow stream to
become distorted or reduce the flow rate. To remove the debris
or mineral build-up, run water through the hand shower, firmly
press or rub your finger back and forth across the rubber nozzles.
Remove and clean the screen washer.
3
Advertisement
