Kärcher SC 1 Premium + Floor Kit Original Instructions Manual page 10

Turning Off the Appliance
Illustration
 Disconnect the mains plug from the socket.
 Push the steam button until no more steam is es-
caping. Now, the boiler of the appliance is depres-
surized.
 Push the child lock at the bottom.
Storing the Appliance
Illustration
 Empty water out.
Illustration
 Coil the mains power cable around the water tank
and fasten with a cable clamp.
 Allow the accessories to dry and then store them in
the accessories bag.
 Store the appliance at a dry and frost-proof loca-
tion.
How to Use the Accessories
Important application instructions
Cleaning floor surfaces
It is recommended to sweep or vacuum the floor prior
to using the steam cleaner. This way, the floor is already
cleared of dirt/loose particles prior to the wet cleaning.
Refreshing textiles
Prior to treatment with the steam cleaner, always check
the reaction of the textiles in an inconspicuous location:
Steam at first, then let dry and then check for colour or
shape changes.
Cleaning of Coated or Lacquered Surfaces
When cleaning painted or plastic-coated surfaces, as
found on kitchen and living room furniture, doors, par-
quet; wax, furniture polish, plastic surfaces or paint can
come loose or stains can be created. When cleaning
these surfaces, briefly steam a cloth and wipe the sur-
faces with it.
ATTENTION
Never direct the steam jet at glued edges as the edge
band may loosen. Do not use the steam cleaner on un-
sealed wooden or parquet floors.
Cleaning of Glass
In case of low outside temperatures, especially in the
winter, warm up the window pane by slightly steaming
the entire glass surface. This will prevent tensions on
the surface which might lead to glass breakage.
Then clean the window surface with the hand nozzle
and attachment. Use a squeegee to remove the water
or wipe the surfaces dry.
ATTENTION
Do not direct steam onto the sealed locations of the win-
dow frame to prevent damage.
Steam nozzle / Steam gun
The steam nozzle or steam gun can also be used with-
out accessories, for example:
– to remove odours and wrinkles from hanging
clothes by steaming them at a distance of 10 to 20
cm.
– for moist dusting, by briefly steaming the cloth and
wiping the furniture with it.
Detail nozzle
The closer this nozzle is to the contaminated area, the
higher the cleaning effect, as the temperature and the
steam are highest at the nozzle output. Especially suit-
ed for cleaning difficult access locations, joints, fittings,
drains, sinks, toilets, blinds and heaters. Heavy lime
scale can be drenched in vinegar prior to steam-clean-
ing. Let the vinegar penetrate for about 5 minutes.
Round brush (small)
The round brush can be installed onto the detail nozzle
as an accessory. Attached brushes can therefore be
used to remove heavy soiling.
ATTENTION
Not suitable for cleaning sensitive surfaces.
Illustration
 Attach the round brush to the detail nozzle.
Power nozzle
The power nozzle can be installed onto the detail nozzle
as an accessory.
The power nozzle increases the emission speed of the
steam. Therefore, it is well-suited for cleaning very
tough dirt, blowing out corners, grooves, etc.
Illustration
 Attach the power nozzle to the detail nozzle ac-
cording to the round brush.
Hand nozzle
Pull the terry cloth cover over the hand nozzle. Especial-
ly well-suited for small washable areas, shower stalls
and mirrors.
Floor nozzle
Suited for all washable walls and floor coverings, e.g.
stone floors, tiles and PVC floors. Work slowly on very
dirty surfaces to allow the steam to act on the dirt for a
longer period of time.
Note
Detergent residue or care emulsions that are still pre-
sent on the surface to be cleaned can lead to streaks
during steam cleaning. However, these will disappear
with repeated cleaning procedures.
Illustration
 Attach the floor cloth to the floor nozzle.
1 Fold the floor cloth the long way and place the floor
nozzle on top of it.
2 Open holding clamps.
3 Place the cloth ends into the openings.
4 Close the holding clamps.
– 10