Bpt HEP/306 US Installation Instructions

NOTE: This equipment has been tested and found to com-
ply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to pro-
vide reasonable protection against harmful interference in a residential
installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instruc-
tions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a par-
ticular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
02.2009/2407-3401
HEP/306 US
HEP/312D US
EN INSTALLATION
INSTRUCTIONS
6-BUTTON FRONT PLATE
HEP/306 AND 12-BUTTON FRONT
PLATE HEP/312D
Coded call button front plates. Using
a bus connection, installations of up
to 64 users can be set up. They fea-
ture a green LED lighting system,
and a membrane keypad for making
calls and for waterproofing.
They come with two connectors,
input CBI and output CBO (fig. 3-6),
for connection - using the wires sup-
plied - to the entry panel they are
teamed with (fig. 9).
Technical features
• Supply voltage: power supplied by
the entry panel they are connec-
ted to.
• Current demand: max. 35 mA.
1
• Working temperature range: from
-15 °C to +50 °C.
Installation instructions
The embedding box must be fitted
flush with the wall at an appropriate
height. In the case of video entry
panels, the height should be such as
to exploit the features of the camera
to the full.
For horizontal (fig. 1-2) combina-
tions, remove the hole plugs and
insert the cable guide joints.
Fit the spacer into embedding boxes
to avoid deformation (fig. 2).
It is possible to use the screwdriver
obtained from the spacer to adjust the
potentiometers of the audio modules.
WARNING. Connecting cables
must be fed through one of the
knockout cable entry points, loca-
ted at the bottom of the embed-
ding box (A in fig. 2).
A
Remove the two plugs protecting the
threaded holes in the embedding box
and secure the chassis using the two
screws supplied (fig. 3-6).
Perform the wiring. The name card
can be removed and filled in with the
relevant information by removing the
card clip followed by the actual card
2
itself (fig. 4-7).
BPT S.p.A.
Via Cornia, 1
33079 Sesto al Reghena-PN-Italy
info@bpt.it – www.bpt.it
NOTE. Personalized name cards
can be used up to a maximum of 2
mm thick. In order to fit the front
plate, first insert the upper part in the
top moulding and then, using a
Allenkey s 2.5, tighten the lock
screw (fig. 5-8).
DISPOSAL
Do not litter the environment with
packing material: make sure it is dis-
posed of according to the regula-
tions in force in the country where
the product is used.
When the equipment reaches the
end of its life cycle, take measures to
ensure it is not discarded in the envi-
ronment.
The equipment must be disposed of
in compliance with the regulations in
force, recycling its component parts
wherever possible.
Components that qualify as recy-
clable waste feature the relevant
symbol and the material's abbre-via-
tion.
LEVITON
LEVITON S de RL de CV
LAGO TANA 43 Col HUICHAPAN CP
11290
MEXICO DF Tel 5082 1040
LEA Y CONSERVE ESTE
INSTRUCTIVO
INSTRUCCIONES
E
PARA LA INSTALACION
PLACA CON 6 PULSADORES
HEP/306 Y CON 12 PULSADO-
RES HEP/312D
Placas de pulsadores con llamada
codificada. Permiten, mediante la
conexión al bus, realizar instalacio-
nes con hasta como máximo 64
usuarios.
Disponen de sistema de iluminación
por LED de color verde, de una
1