jablotron JA-158P Quick Start Manual

The JA-158P wireless outdoor PIR detector
The JA-158P is an outdoor intruder wireless detector designed to detect
human body movement in a protected area. It supplements a double-zone
PIR sensor produced by Optex with a Jablotron transmitter enabling the
detector to be used within the JABLOTRON 100 system. The optical part of
the detector has 2 PIR sensors with non-overlapping 94 zone detection,
a high immunity to false alarms and the detection of small animals. The
detector includes an Antimasking function – protection against covering the
view and it also has two tampers (front and back) built-in. They immediately
report opening the detector or attempting tampering. The detector does
a self-test periodically and sends its status to the control panel. The detector
should be installed by a trained technician with a valid certificate issued by
an authorised distributor.
Installation
Choose a proper place for detector installation according to the following:
The detector must be installed in a position where its bottom surface is
parallel to the watched zone (either directly on the wall, or possibly, if a
change of direction is required, the supplied joint can be used). This
condition is essential for good immunity to false alarms. For more
information see Figure 1.
The detector should be installed 2.5 – 3 m above the ground.
No other moving objects (bushes, trees, high grass, etc.) should be
situated in the detection area of the detector. These objects can be
masked out using the supplied foils. Avoid direct action by strong
sources of light (sun reflections). You can use the supplied viewing
hood for this purpose.
When selecting the right place to install your detector, keep in mind
that the best movement detection is provided when the detection
zones intersect Figure 2.
Figure 1
Figure 2
Procedure:
1. Unfasten the securing screw on the bottom side of the upper cover
and remove it.
2. Pull the plastic tab under the lower PIR sensor slightly to remove the
optical part. Warning: Do not touch the detector sensing face
during handling.
3. Use a screwdriver to punch a hole on the right of the bottom detector
cover in order to pull the rear TAMPER cable through (supplied in the
package).
When installed without the joint holder:
Use the Base Mounting Template from the box lid.
Figure 3 detector configuration
The JA-158P wireless outdoor PIR detector
Pull the rear TAMPER cable through the punched hole in the bottom
detector cover and fix a magnetic contact to the place according to
the template (Base side).
Mark a place on the wall where you want to install the detector – i.e.
holes for the screws and the magnet (Wall side), and fix the magnet
to the wall.
Fix the rear cover on the wall while checking the position of the
magnet and the reed contact (they should be as close as possible).
When installed with the joint holder:
Use the Bracket Base Mounting Template from the box lid.
Press the plastic tab to remove the screw cover (secured with
a plastic cord against falling during work).
Unscrew the securing screw (inside under the cover) to loosen the
joint and swivel it to one side to gain access to the installation holes.
Pull the rear TAMPER cable through the cavity in the joint and fix
the magnetic contact in the given place (between plastic lugs).
Mark a place on the wall where you want to install the detector – i.e.
holes for the screws and the magnet (Wall side), and fix the magnet
to the wall.
Fix the joint holder to the wall while checking the position of the
magnet and the reed contact (they must touch).
Now screw the bottom cover together with the joint holder. Remove
the central screw which blocks vertical movement and screw
it through a hole in the bottom cover.
4. Pull the rear TAMPER cable through the opening you have punched in
the bottom detector cover and insert the rear TAMPER connector into
the pins marked EXT.TMP (3) see Figure 4 (remove the jumper
installed in production).
Enrolling the detector to the system
The signal transmitter for wireless communication is located underneath
the optical part of the detector. The batteries are inserted into the battery
holder of the OPTEX motion detector. Use two CR123A (3 V, 1500 mAh)
lithium batteries from the same manufacturer and replace both
batteries at the same time. If an increased lifetime is needed, you can
also use a third battery. The correct position of the batteries is indicated on
the battery holder. Alternatively, LS(T) 14500 (3.6V, AA) lithium batteries can
be used. When inserting the batteries, it is necessary to remove the part of
the holder held in place with a metal clip.
Enrollment procedure to the system:
a. There must be a JA-110R radio module installed in the control
panel.
b. Go to the F-link software, select required position in the Devices
window and launch the enrollment mode by clicking on the Enroll
option.
c. Insert the batteries (mind the correct polarity). When the first battery
has been inserted into the battery holder an enrollment signal is
transmitted to the control panel and the detector is enrolled to the
selected position.
Figure 4 - Transmitter: 1 – terminals, 2 – option DIP switch, 3 – external
tamper connector, 4 – external antenna jumper, 5 – external antenna
If needed the transmitter can be equipped with an AN-80 or AN-81
external antenna connected to the connector (5) and disconnect the
jumper (4).
266
148
Figure 5: Detector dimensions
1 / 2
N.C. N.O.
State (INP) Pulse (INP)
AUX = Fault AUX = antimasking
Not used
Factory settings highlighted by bold letters.
connector
99
MMY51502