jablotron JA-160PC Manual

JA-160PC (90) PIR motion BUS detector with a 90° verification camera
This device is a wireless component of the JABLOTRON JA-100
system. It serves for the detection of human movement in building
interiors and visual alarm confirmation. The camera takes colour photos
with a resolution of up to 640x480 pixels. Photos are taken following
detected movement, which ensures that the cause of the alarm
is always recorded. The camera is equipped with a visible flash for
taking photos in the dark. The images are saved in the internal memory
of the detector and then they are forwarded to the control panel
via radio signal and from the control panel they can be sent
to MyJABLOTRON, ARC and users. The detector can also take a photo
by request. The detector should be installed by a trained technician with
a valid certificate issued by an authorised distributor.
Installation
The detector can be installed on
the wall or in the corner of a room. There
should be no objects which quickly
change temperature (e.g.
appliances) or which move (e.g. curtains
hanging above a radiator, robotic vacuum
cleaners) or pets in the detector's field
of sight. It is not recommended installing
the detector opposite
or in places with intense air circulation
(close to ventilators, heat
air conditioning outlets, unsealed doors,
etc.). There should be no obstacles
in front of the detector which might
obstruct its view of the protected area.
Figure: 1 – flash for illumination; 2 – camera lens;
3 – PIR detector lens; 4 – cover tab;
Avoid installation too close to a ceiling.
Using flash
of the scene due to reflections.
1. Open the detector cover (by pushing the cover
Avoid touching the PIR sensor inside (15) – you could damage it.
2. Take out the PCB – it is held by a tab (9).
3. The recommended installation height is 2.5 m above the floor.
4. Attach the plastic base to the wall using screws (vertically,
with the cover tab facing downwards).
5. Re-insert the PCB and plug the connecting cable (6) into
the connector on the PCB.
Figure: 5 – Camera module; 6 – connection cable; 7 – batteries; 8 – red LED
indicator; 9 – PCB tab; 10 – yellow LED; 11 – yellow LED indicator of Micro
SD card; 12 – Micro SD memory card; 13 – mini USB connector;
14 – tamper contact; 15 – PIR sensor; 16 – production code.
6. Proceed according to the control panel installation manual.
Basic procedure:
a. The control panel must contain already enrolled JA-11xR radio
module.
b. Go to the F-Link software, select the required position
in the Devices tab and launch the enrolment mode by clicking
on the Enroll option.
c. Insert the batteries (mind the correct polarity). When the second
battery has been inserted into the detector, an enrollment signal
is transmitted to the control panel and the detector is enrolled
to the selected position. This is followed by up to three minutes
detector stabilization phase indicated by the illuminated red LED
indicator. If discharged batteries have been inserted the red LED
indicator flashes for 3 minutes.
d. If the detector is enrolled as the first PIR camera or the control
panel is not connected to an external mass storage, F-Link
JA-160PC (90) PIR motion BUS detector with a 90° verification camera
heating
windows
sources,
may cause over-exposure
tab (4)).
shows a dialogue window with the question: "Enable image
transfer to external storage?" We recommend enabling this
option with the agreement of the customer and confirming this
acceptance by recording it in the system service log with his
signature.
Note: If the transmission is not enabled, images will be saved in the
internal memory of the detector and the control panel only. Then
it is impossible to send them to users' cell phones and e-mails.
7. Close the detector cover and test its functionality. When
the detector has been closed, it starts the 15 minute test mode
during which it indicates and reports every movement. After that,
the red LED will not indicate movement and the detector works
in the standard mode.
Notes:
- When the control panel is in service mode, the detector indicates
every movement with the red LED indicator.
- If you want to enroll the detector in the control panel after the battery
has already been inserted, remove the battery first and then press
and release the tamper contact (14) to discharge the rest of the
energy and then enroll the detector.
- The detector can be enrolled by entering the production code (16)
in the F-Link software (or a bar code reader). Enter all digits located
below the bar code (1400-00-0000-0001).
- If you want to remove the detector from the system, erase it from its
position in the control panel.
- In order to comply with the EN 50131-2-4 norm, the cover tab (4)
must be secured with the supplied screw.
Detector internal settings
Settings can be set by F-Link software in the Devices tab. Use the
Internal settings option on the detector's position to open a dialog
window where you can configure the settings (* default settings):
PIR immunity level: Defines false alarm immunity. The *Standard level
combines basic immunity with a rapid reaction. The Increased level provides
higher immunity but the detector reaction is slower.
LQ photo quality: Standard* quality uses optimized compression in order
to achieve the fastest possible transfer to the ARC or to the end user
in MyJABLOTRON. The goal is achieving alarm verification in the fastest
time possible. If the quality is switched to Extended, the system will use
lower image compression which will at least double the time necessary
to transfer the image (depends on the conditions of the captured scene).
Change the quality only if the LQ image does not have the quality required
by the customer – it may depend on the captured space. It is not
recommended when there are more verification detectors in the premises
which may take images at the same time.
Taking photos during alarms: No flash, *With flash
Flash intensity: Low, *Medium, High – if the captured scene is over-
exposed (e.g.in a small room), the intensity of the flash can be decreased.
It can be increased for larger spaces.
Lithium battery operation: If the detector is tasked with frequent
operation (e.g. frequently requested photos by MyJABLOTRON) and
is configured to high flash intensity, we recommend the use of AA 1.5 V
lithium batteries. If you operate the detector from lithium batteries,
this parameter must be enabled (it adjusts detection of low batteries).
PG output reaction: You can select PG outputs, whose activation will
trigger taking a picture (* No, camera does not react to PG). For further info
see Installation recommendations, cautions.
Taking a photo by PG activation: No flash, *With flash
Taking photos during entrance delay: *No flash, With flash
Send pre-alarm photos: This option is not available when the Extended
LQ photo quality is selected due to more than double size of the photo and
therefore longer transmission time. When this parameter is enabled the
detector will send photos even when the detector is configured with repeated
or confirmed reaction and the alarm has not been confirmed. During every
entrance delay, up to two photos can be taken when the detector is triggered
even when the system has been unset properly.
This option will noticeably increase the volume of data transferred
to MyJABLOTRON or external mass storage. If the system is unset (alarm is
triggered), the images taken during the entrance delay will be sent
automatically regardless this option
Test: takes a test photo (LQ) with a flash and F-Link displays it. When the
Detail button is pressed, the F-Link software shows the picture in a 640x480
px resolution. Photos are sent to the external mass storage (provided that
transferring is enabled).
To set the JA-160PC (90) detector to comply
with security grade 2 or other requirements use
F-Link SW, Parameters tab and the option
"System profiles".
Camera and basic reactions
The process of how the
on the settings in the F-Link software – the Devices tab. Choose a type
of Reaction on the detector's position.
1 / 3
camera takes pictures depends
MMQ53102