Toshiba D-R400 Owner's Manual page 98

Symptom
DV
DV signal cannot be input.
The DVC cannot be operated
with this unit.
Certain functions of the unit
cannot operate.
DV audio signal cannot be
switched.
HDMI
No image from HDMI connection.
There is no sound or the sound is
distorted.
Others
The unit does not operate
properly.
The disc tray does not open when
you press [OPEN/CLOSE A].
"Repairing" appears on the TV
screen.
Repairing
In a case you intend to cancel the
repairing process.
Do you want to cancel a repairing process ?
When selecting "Yes", the disc may not be
usable.
Yes
No
Repairing
98 98 EN EN
E7E7AUD_EN.indb 98 E7E7AUD_EN.indb 98
TROUBLESHOOTING
• Before connection, turn on the power supplies for both this unit and the DVC,
and make sure that these units are in stop mode.
• Only a "DVC-SD" signal can be input from the DVC to this unit. Other types of
signals are not supported.
• Do not connect any device other than the DVC. Even if a recorder or PC with
another DV terminal is connected, the DV function will not operate.
• If the DVC is not recognized after connection, turn off the power supply for
the unit and re-connect the DVC.
• Signal input or DVC operation from this unit may be disabled depending on
the type of DVC.
• If a DVC signal cannot be input, use an external input (L1/L2) for analog
connection via audio/video cables.
• DVC control may be disabled depending on the type of DVC, even in a mode
other than camera mode. In this case, switch to DVD control and execute the
normal recording procedure while operating the DVC.
• Some functions may not operate depending on the type of DVC. For
example, if the DVC does not support slow playback mode, the slow playback
function is disabled.
• With L3 (DV), the disc display menu does not appear unless disc playback is
executed.
• For recording with the DVC, the recording audio signal can be set to 12 bits
or 16 bits. However, when 16-bit recording mode is selected, audio signal
cannot be switched. To record an audio signal, set it to 12 bits.
• Check the HDMI connection. (Check the status of the HDMI related
indications.)
• Check whether the connected monitor device or other device supports
HDCP. (This unit will not output a video signal unless the other device
supports HDCP.)
• Check the setting of HDMI.
• Check whether the output format of this unit (HDMI FORMAT) matches the
supported input format of other connected device.
• The HDMI sound is not output when "HDMI Audio" is set to "OFF".
• Check the RCA audio cable connection. If you are using HDMI-DVI conversion
cable, you must connect the RCA audio cable, too.
• Check whether the output format of this unit (HDMI FORMAT) matches the
supported input format of other connected device.
• When static electricity, etc., causes the unit to operate abnormally, unplug
the unit and then plug it in again.
• It may take a few seconds for the disc tray to open after you have recorded or
edited a disc. This is because the unit is adding disc data to the disc.
• If there is a power failure or unplugging during recording, finalizing,
formatting or editing (even after "Repairing" disappears), a repairing process
will begin automatically just after turning the unit on again.
It may take several minutes up to about several hours.
• If you intend to cancel the repairing process, press [OPEN/CLOSE A]
on the front panel, then select "Yes" and press [ENTER]. After that, press
[OPEN/CLOSE A] to take out the disc. The disc canceled during the
repairing process MAY NOT work.
Remedy
2007/01/29 19:04:40 2007/01/29 19:04:40