Codan Envoy 2220 Getting Started Manual
  1. Manuals
  2. Brands
  3. Codan Manuals
  4. Transceiver
  5. Envoy 2220
  6. Getting started manual

Codan Envoy 2220 Getting Started Manual

Radio communications
Hide thumbs
Table of Contents

Advertisement

Quick Links

RADIO COMMUNICATIONS
Envoy™ Transceiver
Getting Started Guide

Advertisement

Table of Contents
loading

Related Manuals for Codan Envoy 2220

Summary of Contents for Codan Envoy 2220

  • Page 1 RADIO COMMUNICATIONS Envoy™ Transceiver Getting Started Guide...
  • Page 2 Codan Limited. © Copyright 2012 Codan Limited. Codan part number 15-04177-EN Issue 1, December 2012. CODAN™, Envoy™, Easitalk™, and CALM™ are trademarks of Codan Limited. Other brand, product, and company names mentioned in this document are trademarks or registered trademarks of their respective holders.

  • Page 3: Table Of Contents

    ABLE OF CONTENTS Table of contents Section 1 Introduction Overview of this guide ....2 The 2220 Handset ..... . 3 The 2221 Handset .
  • Page 4 ABLE OF CONTENTS Switching between basic and advanced views ..31 Finding a word or value ....32 Selecting an icon .
  • Page 5 ABLE OF CONTENTS Adding a Phone call ....72 Adding a Get Status call ....73 Adding an RFDS Emergency call .
  • Page 6 ABLE OF CONTENTS This page has been left blank intentionally. ™ T NVOY RANSCEIVER ETTING TARTED UIDE...
  • Page 7 IST OF FIGURES List of figures Figure 1: 2220 Handset ....... . 3 Figure 2: 2221 Handset .
  • Page 8 IST OF FIGURES This page has been left blank intentionally. ™ T NVOY RANSCEIVER ETTING TARTED UIDE...
  • Page 9 IST OF TABLES List of tables Table 1: Keys and their function ......8 Table 2: Character-entry mode ......39 Table 3: Specifications .
  • Page 10 IST OF TABLES This page has been left blank intentionally. viii ™ T NVOY RANSCEIVER ETTING TARTED UIDE...
  • Page 11 HF communications needs. You can expect many years of reliable high performance, and if ever assistance is required, Codan’s world-class after-sales support team is ready to help. Please read this guide thoroughly and retain it for future reference.

  • Page 12: Introduction

    NTRODUCTION VERVIEW OF THIS GUIDE Overview of this guide This guide provides instructions on how to connect up your Envoy™ Transceiver, and how to perform basic setup and operating tasks. It assumes that you have limited knowledge of HF communication and of using an HF transceiver. Detailed information for setting up a particular system and extensive reference material are provided on the CD at the back of this guide.

  • Page 13: The 2220 Handset

    NTRODUCTION 2220 H ANDSET The 2220 Handset The 2220 Handset is a control point for the Envoy™ Transceiver. The user interface provides an icon-based menu structure for easy setup and operation of the transceiver. Figure 1: 2220 Handset Power key microphone Emergency key screen...
  • Page 14 NTRODUCTION 2220 H ANDSET The 2220 Handset is shipped from the factory with standard hot keys programmed to the numeric keys. The function that each standard hot key performs is written on the numeric key in blue text. You may also add your own macros and assign these to a hot key.

  • Page 15: The 2221 Handset

    NTRODUCTION 2221 H ANDSET The 2221 Handset The 2221 Handset is a control point for the Envoy™ Transceiver. The user interface provides an icon-based menu structure for easy operation of the transceiver. It has a condensed set of keys for use in simpler communication scenarios.
  • Page 16 NTRODUCTION 2221 H ANDSET The 2221 Handset is a hand-held device that has a microphone, a PTT button, a screen, and navigation keys. The navigation keys enable you to operate the transceiver system via the user interface using pre-defined profile information. Typically, this profile is fully configured using the TPS system programmer.

  • Page 17: The 2230 Desk Console

    NTRODUCTION 2230 D ONSOLE The 2230 Desk Console The 2230 Desk Console is a control point for the Envoy™ Transceiver. The user interface provides an icon-based menu structure for easy setup and operation of the transceiver. The desk console is an optional accessory for a fixed station. Figure 3: 2230 Desk Console s p e a k e...

  • Page 18: Keypad

    NTRODUCTION EYPAD Keypad Standard macros are programmed in the transceiver in the factory. You can create a macro and assign it to a hot key. Table 1: Keys and their function Function Switches on the transceiver. Switches off the transceiver (hold for 2 sec). Performs a hot-key sequence with another key (hold + key): + 0 jumps to the Brightness screen + 2 toggles advanced view...
  • Page 19 NTRODUCTION EYPAD Table 1: Keys and their function (cont.) Function Scrolls down in a list of entries. Moves the highlight down a row. Enters the submenu or list of entries represented by the selected icon. Toggles the selection of a check box. CALL Starts the calling process by jumping to the call screen.
  • Page 20 NTRODUCTION EYPAD Table 1: Keys and their function (cont.) Function Enters 8, t, u, v, T, U, V in character-entry mode. Toggles secure mode on and off. Enables you to enter a PIN for a secure session, or access secure information (hold for 2 sec). Enters 9, w, x, y, W, X, Y in character-entry mode.

  • Page 21: Accessing The Cd

    NTRODUCTION CCESSING THE Accessing the CD To access the CD: Place the CD in the CD drive of your computer. You can view and search the Reference Manual and Getting Started Guide using the Adobe® Reader® supplied on the ™ T NVOY RANSCEIVER ETTING...

  • Page 22: Standards And Icons

    NTRODUCTION TANDARDS AND ICONS Standards and icons The following standards and icons are used: This typeface... Means... Italic a cross-reference or text requiring emphasis Bold a key on a computer keyboard Bold a menu, submenu, tab, entry, or value in the user interface of the control point ™...

  • Page 23: Using The Wizard

    Using the wizard This section contains the following topics: • Using the wizard on page 14 • Selecting a language on page 15 • Setting the time and date on page 15 • Setting the location of the desk console on page 16 •...

  • Page 24: Using The Wizard

    SING THE WIZARD SING THE WIZARD Using the wizard The wizard should start automatically when a new transceiver is powered up for the first time. Figure 4: Wizard Startup screen NOTE: If the wizard screen doesn’t launch automatically, follow the instructions below. If your transceiver has been profiled using TPS, the wizard may not be available.

  • Page 25: Selecting A Language

    SING THE WIZARD SING THE WIZARD Press (Yes) to confirm that you want to start the wizard. If you want to bypass the wizard, press (No). Selecting a language NOTE: This step in the wizard is shown if you have multiple languages available.

  • Page 26: Setting The Location Of The Desk Console

    SING THE WIZARD SING THE WIZARD Press to scroll to the value that you want to set, then press to move to the next item. Repeat this for the day/month and year, as required. Press (Save) to save the local date. Press to move to the Clock entry.

  • Page 27: Adding A Channel

    SING THE WIZARD SING THE WIZARD Adding a channel NOTE: This step in the wizard is shown if you are permitted to add channels. To add a channel: Press (Yes) to add a channel, if required. Enter the name that you want to use for the channel, then press to move to the Tx entry.
  • Page 28 SING THE WIZARD SING THE WIZARD Do one of the following: • If you want to add a scan table, press (Yes). • If you do not want to add a scan table, press (No), then continue from Entering a self address on page Do one of the following: •...

  • Page 29: Entering A Self Address

    SING THE WIZARD SING THE WIZARD (Options), scroll to Save, then press Press (Select). Press (Save) to save the information. Entering a self address To enter a self address: Enter the address that you want to use. You can enter up to six digits. NOTE: Addresses ending in 99 and 00 have a special function in Selcall HF networks.

  • Page 30: Adding A Contact

    SING THE WIZARD SING THE WIZARD Adding a contact To add a contact: Enter the name that you want to use for the contact, then (Add Call). press The HF Network entry is highlighted. Press to scroll through the available HF networks until the one you want to use is shown.
  • Page 31 SING THE WIZARD SING THE WIZARD Adding a Message call To continue with adding a Message call: to move to the Selcall | ALE Address entry. Press Enter the address of the station that you want to call. to move to the Message entry, then press Press If you want to enter a message: •...
  • Page 32 SING THE WIZARD SING THE WIZARD Adding a Phone call To continue with adding a Phone call: to move to the Phone Number entry. Press Enter the phone number. Continue from Completing the contact on page Adding a Get Status call To continue with adding a Get Status call: Press to move to the Selcall | ALE Address entry.

  • Page 33: Selecting An Antenna

    SING THE WIZARD SING THE WIZARD If you want to add another contact, press (Yes), then repeat the steps for adding a contact. If you do not want to add another contact, press (No). Do one of the following: • If you want to select an antenna, continue from Selecting an antenna on page 23 •...

  • Page 34: Selecting A Peripheral Device

    SING THE WIZARD SING THE WIZARD Do one of the following: • If you want to connect accessories to the 15-way port of the RF unit, press (Yes), then continue from Selecting a peripheral device on page • If you do not want to connect an accessory, press (No), then press OK to close the wizard.

  • Page 35: Navigating The Menu Structure

    Navigating the menu structure This section contains the following topics: • The basic menu structure on page 26 • Navigating the menu structure on page 28 • Overview of basic and advanced views on page 29 • Switching between basic and advanced views on page 31 •...

  • Page 36: The Basic Menu Structure

    AVIGATING THE MENU STRUCTURE HE BASIC MENU STRUCTURE The basic menu structure The menu structure comprises a main menu and a series of submenus that are accessed via the main menu. Each menu and submenu is represented by an icon. Some icons provide direct access to an input/view screen, while other icons provide a list of entries for the menu.

  • Page 37: Figure 6: Menu Structure (User Level, Basic View)

    AVIGATING THE MENU STRUCTURE HE BASIC MENU STRUCTURE Figure 6: Menu structure (user level, basic view) Setup Wizard Add Channel User Data Channels Scan Tables HF Networks Contacts Messages Modes Peripherals Settings Control Point Configuration Connectors Scan Calling Admin Login/Logout Advanced View Information Device Information...

  • Page 38: Navigating The Menu Structure

    AVIGATING THE MENU STRUCTURE AVIGATING THE MENU STRUCTURE Navigating the menu structure The menu structure comprises a main menu and a series of submenus that are accessed via the main menu. Navigation keys enable you to highlight an icon, then press OK to select that menu. You can continue drilling down through the menu structure in this way.

  • Page 39: Overview Of Basic And Advanced Views

    AVIGATING THE MENU STRUCTURE VERVIEW OF BASIC AND ADVANCED VIEWS Overview of basic and advanced views There are two views of information in the user interface of the control point: basic and advanced. The contents of basic and advanced views are pre-determined and cannot be changed. Basic view Basic view provides a condensed view of the user interface, and typically the view at which the control point is operated.

  • Page 40: Figure 8: Advanced View

    AVIGATING THE MENU STRUCTURE VERVIEW OF BASIC AND ADVANCED VIEWS Figure 8: Advanced view advanced view indicator ™ T NVOY RANSCEIVER ETTING TARTED UIDE...

  • Page 41: Switching Between Basic And Advanced Views

    AVIGATING THE MENU STRUCTURE WITCHING BETWEEN BASIC AND ADVANCED VIEWS Switching between basic and advanced views The user can switch between basic and advanced views to either: • simplify the user interface of the control point (basic view), • access advanced settings that they are permitted to change (advanced view) To switch between views: Press...

  • Page 42: Finding A Word Or Value

    AVIGATING THE MENU STRUCTURE INDING A WORD OR VALUE Finding a word or value The quickest way to find an entry or a value in the user interface of the control point is to use the Find function, which is available via key when the icon selected contains submenus or lists of entries.

  • Page 43: Figure 9: Find Function

    AVIGATING THE MENU STRUCTURE INDING A WORD OR VALUE Figure 9: Find function ™ T NVOY RANSCEIVER ETTING TARTED UIDE...
  • Page 44 AVIGATING THE MENU STRUCTURE INDING A WORD OR VALUE To find a word or value: Highlight the icon that represents the highest level in which you want to search, then press (Find). Start entering the letter and/or number on which you want to search.

  • Page 45: Selecting An Icon

    AVIGATING THE MENU STRUCTURE ELECTING AN ICON Selecting an icon The top levels of the menu structure are represented by icons. In order to enter the menu represented by the icon, you need to select the icon. Figure 10: Highlighted icon highlighted icon To select an icon: to highlight the icon that you want to...

  • Page 46: Selecting A Function From The Menu Bar

    AVIGATING THE MENU STRUCTURE ELECTING A FUNCTION FROM THE MENU BAR Selecting a function from the menu bar The menu bar at the bottom of the screen provides varying functions, depending on the context. You can select a function directly, or activate a pop-up from the menu bar by pressing the corresponding key ( ).
  • Page 47 AVIGATING THE MENU STRUCTURE ELECTING A FUNCTION FROM THE MENU BAR If a pop-up of available functions is shown: • Press until the function that you want to select is highlighted. Press OK. • The function is performed. ™ T NVOY RANSCEIVER ETTING...

  • Page 48: Entering Text In A Field

    AVIGATING THE MENU STRUCTURE NTERING TEXT IN A FIELD Entering text in a field You may need to enter text into a field within an entry. This may be a name given to some user data, or it may be a specific value, such as a frequency.

  • Page 49: Table 2: Character-Entry Mode

    AVIGATING THE MENU STRUCTURE NTERING TEXT IN A FIELD Table 2: Character-entry mode Character-entry mode Icon All upper-case letters All lower-case letters Leading-capital letters Numbers Do any of the following: • Press to move the cursor to the point at which you want to enter text.

  • Page 50: Entering Special Characters

    AVIGATING THE MENU STRUCTURE NTERING TEXT IN A FIELD Entering special characters You can enter special characters in messages and names, and in addresses of stations that you call. NOTE: If the FED-STD-1045 ALE/CALM option or MIL-STD-188-141B ALE option is installed in your transceiver, the key may be used to enter the global ALL address syntax (@?@) or special...

  • Page 51: Entering Text In The 2221 Handset

    AVIGATING THE MENU STRUCTURE NTERING TEXT IN A FIELD Entering text in the 2221 Handset The 2221 Handset does not have alphanumeric keys, however, you can still enter text into fields within the user interface. To enter text: Navigate to a field in which you can enter text, then press OK to see the virtual keypad.

  • Page 52: Selecting A Value From A List

    AVIGATING THE MENU STRUCTURE ELECTING A VALUE FROM A LIST Selecting a value from a list When you select an entry that has a list of values, either by selecting an icon or using the navigation keys, the field is highlighted to show that it can be edited, and indicators appear on one or both sides of the field to show that values are available.

  • Page 53: Selecting/Deselecting A Check Box

    AVIGATING THE MENU STRUCTURE ELECTING DESELECTING A CHECK BOX Selecting/deselecting a check box There are some entries in the menu structure that require you to enable or disable a particular feature via a check box. When the check box contains a , the feature is enabled.

  • Page 54: Moving A Slider

    AVIGATING THE MENU STRUCTURE OVING A SLIDER Moving a slider Some values in the user interface of the control point are represented by a slider. Figure 15: A slider value slider navigation key indicator To move a slider: Press any of the navigation keys suggested in the navigation key indicator to adjust the slider.

  • Page 55: Changing The Order Of Items In A List

    AVIGATING THE MENU STRUCTURE HANGING THE ORDER OF ITEMS IN A LIST Changing the order of items in a list In some areas of the control point, you are able to change the order in which the items appear, which impacts how the item is viewed, or when each item may be used.

  • Page 56: Saving Your Changes

    AVIGATING THE MENU STRUCTURE AVING YOUR CHANGES Saving your changes When information in an entry has been changed, either by editing existing text or selecting a different value from a list, an asterisk is added to the title of the screen. Figure 16: Screen that has changes to be saved To save changes: Do one of the following:...

  • Page 57: Operating The Transceiver

    Operating the transceiver This section contains the following topics: • Switching the transceiver on and off on page 48 • The channel screen on page 49 • Scanning channels on page 52 • Muting the transceiver on page 54 • Using the microphone on page 56 •...

  • Page 58: Switching The Transceiver On And Off

    PERATING THE TRANSCEIVER WITCHING THE TRANSCEIVER ON AND OFF Switching the transceiver on and off Switching on the transceiver To switch on the transceiver: Press The template screen, then the welcome screen (if set) is shown briefly, followed by the channel screen. Switching off the transceiver To switch off the transceiver: Hold down...

  • Page 59: The Channel Screen

    PERATING THE TRANSCEIVER HE CHANNEL SCREEN The channel screen The channel screen shows the following information: • the name of the currently selected channel • the transmit and receive frequencies, if applicable • a bar graph that indicates the signal strength on receive (green) and the output power on transmit (red) •...

  • Page 60: Figure 18: Scanning Screen

    PERATING THE TRANSCEIVER HE CHANNEL SCREEN If the transmit and receive frequencies are the same, the frequency is only shown on the right side of the screen. The Rx/Tx indicator shows whether the transceiver is receiving (green) or transmitting (red). The more bars that are shown, the higher the signal strength. Your transceiver may have the option of selecting high, medium, or low power.

  • Page 61: Selecting A Channel

    PERATING THE TRANSCEIVER HE CHANNEL SCREEN Selecting a channel To select a channel: Press PTT to exit to the channel or scanning screen. If the transceiver is scanning, press SCAN to switch off scanning. Press to scroll through the channels. Stop scrolling when the channel that you want is shown on the screen.

  • Page 62: Scanning Channels

    PERATING THE TRANSCEIVER CANNING CHANNELS Scanning channels If you intend to receive calls on several channel/modes, switch on scanning. When scanning is switched on, the transceiver sequentially selects each channel/mode in your HF network to detect incoming calls. The channel/modes are scanned in a continuous cycle.

  • Page 63: Pausing Scanning

    PERATING THE TRANSCEIVER CANNING CHANNELS Pausing scanning To pause scanning: Do one of the following: • To pause scanning on the last-selected channel, press OK. • To pause scanning and scroll to another channel, press The channel/modes through which you can scroll are those in the scan tables that are being scanned.

  • Page 64: Muting The Transceiver

    PERATING THE TRANSCEIVER UTING THE TRANSCEIVER Muting the transceiver When the transceiver is set to a channel or is scanning channels, and mute is switched off, you hear on-air signals on each channel. If you do not want to listen to this, you can silence the transceiver by switching mute on.

  • Page 65: Selecting The Mute Type

    PERATING THE TRANSCEIVER UTING THE TRANSCEIVER Selecting the mute type To select the mute type: Press to toggle the mute type between Selcall mute (S) and Voice mute (V). NOTE: If you have the AES-256 digital voice encryptor fitted, an additional mute type of Digital Voice Only mute (D) is available.

  • Page 66: Using The Microphone

    PERATING THE TRANSCEIVER SING THE MICROPHONE Using the microphone The microphone is located at the top centre of your handset. When you talk into the microphone: • hold the microphone side-on and close to your mouth • hold down PTT •...

  • Page 67: Setting The Date And Time

    PERATING THE TRANSCEIVER ETTING THE DATE AND TIME Setting the date and time The transceiver is set to UTC time in the factory. You set the local time and time zone offset for the location of the control point. This feature is useful if you have a network that spreads over several time zones, or you need to time stamp your transmissions according to the current time at longitude zero.
  • Page 68 PERATING THE TRANSCEIVER ETTING THE DATE AND TIME to move to the Date Format entry. Press Press to select the format that you want to use. If you want to review the information that you have entered, press to move through the entries. Press (Save) to save the information.

  • Page 69: Calling

    PERATING THE TRANSCEIVER ALLING Calling This section describes how to make the various types of calls from the transceiver. Figure 19: Call screen navigation call type HF network indicator address incoming call outgoing call select HF network NOTE: Additional call types are discussed in the Reference Manual.

  • Page 70: Making A Selective Call

    PERATING THE TRANSCEIVER ALLING Making a Selective call If you want to speak with the operator at a particular station, make a Selective call to the address of that station. When the station receives the call, the transceiver sounds an alert tone to notify the operator.

  • Page 71: Making A Message Call

    PERATING THE TRANSCEIVER ALLING Do one of the following: • To repeat the call to the last address used, press CALL. • To call a different station, enter the address, then press CALL. • To repeat or return a call from the call log, press to scroll to the call, then press CALL.
  • Page 72 PERATING THE TRANSCEIVER ALLING To make a Message call: Press CALL. Do one of the following: • Press to scroll to the HF network that you want to use, then press CALL. • Press (Options), scroll to HF Networks, press (Select), scroll to the HF network that you want to use, then press CALL.
  • Page 73 PERATING THE TRANSCEIVER ALLING If you want to enter a message: • Start typing the message. NOTE: Press OK to start a new line, if required. • Press (Options), scroll to Save, then press (Select) to add the message to the call. If you want to select a message from a list of stored messages: •...

  • Page 74: Making A Call To A Contact

    PERATING THE TRANSCEIVER ALLING Press CALL. To abort the call before it is answered, press PTT or SCAN. There will be audible beeps or a pop-up message to indicate that the call has been successful. Making a call to a contact To make a call to a contact: Hold CALL.

  • Page 75: Making A Call From The Call History

    PERATING THE TRANSCEIVER ALLING Making a call from the Call History The Envoy™ Transceiver stores information on the calls that you send and receive. The detailed call history is accessed by holding CALL, then pressing to scroll to the Call History tab. NOTE: A filtered call log is available in the call screen.

  • Page 76: Making A Call From The Emergency Key

    PERATING THE TRANSCEIVER ALLING Making a call from the Emergency key You can set up emergency contacts with calls that are chained together when you hold the key. CAUTION: If you have more than one emergency contact, you will be prompted to select the emergency contact that you want to call at the time of the call.

  • Page 77: Upgrading The Transceiver Via A Usb Stick

    PERATING THE TRANSCEIVER PGRADING THE TRANSCEIVER VIA A STICK Upgrading the transceiver via a USB stick Firmware packages, profiles from TPS, and secure keys may be loaded onto a USB stick, providing a portable method of upgrading transceivers in the field. You can also read a profile from a transceiver in the field.
  • Page 78 PERATING THE TRANSCEIVER PGRADING THE TRANSCEIVER VIA A STICK Perform more tasks with the USB stick as required. Press (Eject) when you have finished working with the USB stick. ™ T NVOY RANSCEIVER ETTING TARTED UIDE...
  • Page 79 Contacts This section contains the following topics: • Adding a contact on page 70 • Adding a contact from an entry in the Call Log or Call History on page 75 ™ T NVOY RANSCEIVER ETTING TARTED UIDE...

  • Page 80: Adding A Contact

    ONTACTS DDING A CONTACT Adding a contact Contacts are used to pre-define the typical calls that you want to make to another person. For each contact you can define a number of calls. Each call contains information about: • the call system that you want to use •...

  • Page 81: Adding A Simple Call

    ONTACTS DDING A CONTACT If you are adding: • a Selective, Channel Test, Emergency, Get Position or Send Position call, continue from Adding a simple call on page 71 • a Message call, continue from Adding a Message call on page 71 •...

  • Page 82: Adding A Phone Call

    ONTACTS DDING A CONTACT If you want to enter a message: • Start typing the message. NOTE: Press OK to start a new line, if required. • Press (Options), scroll to Save, then press (Select) to add the message to the call. If you want to select a message from a list of stored messages: (Options), scroll to Stored, then...

  • Page 83: Adding A Get Status Call

    ONTACTS DDING A CONTACT Adding a Get Status call To continue with adding a Get Status call: to move to the Selcall | ALE Address entry. Press Enter the address of the station that you want to call. to move to the Status Type entry, then press Press Press to scroll to the status type that you want to...

  • Page 84: Completing The Contact

    ONTACTS DDING A CONTACT Completing the contact To finish entering the information required for the contact: to move to the Call Description entry. Press By default, the call type is entered as the call description. Enter the description that you want to use for this call. Press (Save) to save the information.

  • Page 85: Adding A Contact From An Entry In The Call Log Or Call History

    ONTACTS DDING A CONTACT FROM AN ENTRY IN THE OG OR ISTORY Adding a contact from an entry in the Call Log or Call History You can save information from the Call Log or Call History to Contacts. This can either be a new call type for an existing contact, or you can add a new contact to hold this call information.
  • Page 86 ONTACTS DDING A CONTACT FROM AN ENTRY IN THE OG OR ISTORY Do one of the following: • If there is an existing contact, select the contact, press OK, then edit the call as required. • If there is no matching contact, edit the call as required.

  • Page 87: Specifications

    Specifications Table 3: Specifications Item Specification Frequency range Transmit: 1.6 to 30 MHz Receive: 0.25 to 30 MHz Channel capacity (single or two-frequency simplex channels) 1000 Operating modes Single sideband (J3E) USB and LSB or switched USB/LSB, AM (A3E Rx, H3E Tx), CW (J1A, A1A) Environment Ambient temperature: −30 to +60°C...
  • Page 88 PECIFICATIONS Table 3: Specifications (cont.) Item Specification Size 2210 RF 210 mm W × 270 mm D × 65 mm H Unit: (8.4 in W × 10.8 in D × 2.6 in H) 2220/2221 74 mm W × 32 mm D × 150 mm H Handset: (2.9 in W ×...

  • Page 89: Appendix A Installing The Transceiver

    Installing the transceiver This section contains the following topics: • Overview of mobile stations on page 80 • Overview of fixed stations on page 86 Envoy™ Transceiver Getting Started Guide...

  • Page 90: Overview Of Mobile Stations

    NSTALLING THE TRANSCEIVER VERVIEW OF MOBILE STATIONS Overview of mobile stations A mobile station typically consists of a transceiver, a 12 V DC power supply (battery), an antenna, control and accessory devices, ancillary equipment, and appropriate connecting cables. The antenna is connected to the transceiver by coaxial cable. An automatic tuning antenna also requires a control cable connected to the transceiver.

  • Page 91: Figure 21: Typical Mobile Station

    NSTALLING THE TRANSCEIVER VERVIEW OF MOBILE STATIONS Figure 21: Typical mobile station r o l o n t e n n a n t e n n a n t t e r b a t t o r 1 5 - u n i n e c c o n...

  • Page 92: Cables In A Mobile Station

    CD. Mounting the handset cradle To mount the handset cradle: Mount the handset according to the fitting instructions (Codan part number 15-00149-001) provided with the handset cradle. Envoy™ Transceiver Getting Started Guide...
  • Page 93 NSTALLING THE TRANSCEIVER VERVIEW OF MOBILE STATIONS Mounting the speaker To mount the speaker: Secure the mounting cradle to the surface with at least two screws. Ensure there is sufficient space at the rear for the cable. Attach the speaker to the cradle with the two screws and rubber washers.

  • Page 94: Connecting A Mobile Envoy™ Station

    NSTALLING THE TRANSCEIVER VERVIEW OF MOBILE STATIONS Place the RF unit into the cradle and push it under the tabs at the rear of the cradle, then hold the clamp against the front of the RF unit. Rotate the key clockwise, then push the key toward the base of the cradle to lock the RF unit into position.
  • Page 95 To connect the transceiver to the battery power supply: If you are using a 24 V battery supply, connect the battery to a 24 V to 12 V voltage regulator (Codan part number 15-00508). Connect the power supply cable (Codan part number 08-03255) to the plug at the end of the 12 V cable lead from the RF unit.

  • Page 96: Overview Of Fixed Stations

    NSTALLING THE TRANSCEIVER VERVIEW OF FIXED STATIONS Overview of fixed stations A fixed station typically consists of a transceiver, an AC transceiver supply connected directly to the mains, an antenna, control and accessory devices, ancillary equipment, and appropriate connecting cables. The transceiver is connected to the DC output lead of the transceiver supply.

  • Page 97: Figure 22: Typical Fixed Station

    NSTALLING THE TRANSCEIVER VERVIEW OF FIXED STATIONS Figure 22: Typical fixed station i o n o p t t u n r o l o n t e n n a n t e n n a n t b r o a d b t e r a n t...

  • Page 98: Cables In A Fixed Station

    The RF unit and the transceiver supply are self-contained and are usually stacked loosely. If you want to mount the RF unit and/or the transceiver supply, contact your Codan representative to obtain a rack-mounting unit or the appropriate mounting cradles.

  • Page 99: Connecting A Fixed Envoy™ Station

    NSTALLING THE TRANSCEIVER VERVIEW OF FIXED STATIONS Rack-mounting unit A rack-mounting unit consists of a 19 inch rack tray. It can be used to mount your fixed station with either a desk console or the handset and cradle. Connecting a fixed Envoy™ station To connect a fixed station: Do one of the following: •...
  • Page 100 NSTALLING THE TRANSCEIVER VERVIEW OF FIXED STATIONS Connecting a desk console The desk console may be attached directly to the RFU using cable 08-07205-xxx, or remotely via Ethernet. Connecting an automatic tuner to the RF unit and antenna (optional) NOTE: You may need to install a tuner to improve the efficiency of the antenna in your fixed station (see the reference material on the enclosed CD).
  • Page 101 Compliance This section contains the following topics: • Overview on page 92 • European R&TTE Directive on page 93 • EMC and safety notices on page 96 • RCM approval on page 99 Envoy™ Transceiver Getting Started Guide...

  • Page 102: Appendix B Compliance Overview

    OMPLIANCE VERVIEW Overview This section describes how to ensure the Envoy™ Transceiver complies with the European R&TTE Directive 1999/5/EC. This section also contains the requirements for RCM. Envoy™ Transceiver Getting Started Guide...

  • Page 103: European R&Tte Directive

    Article 3.1a: (LVD) EN 60950-1:2006/AC:2011 • Article 3.1a: (MPE) EN 62311:2008 Product marking and labelling Any equipment supplied by Codan that satisfies these requirements is identified by the markings displayed on the product. Radiation safety (EU installations only) To ensure optimal transceiver performance and to avoid exposure to excessive electromagnetic fields, the antenna system must be installed according to the instructions provided.

  • Page 104: Declaration Of Conformity And Notified Body Letter Of Opinion

    EN 62311:2008. Declaration of Conformity and Notified Body Letter of Opinion The CE Declaration of Conformity and Notified Body Letter of Opinion for this product are available upon request to Codan or a Codan-authorised supplier. Protection of the radio spectrum CAUTION:...
  • Page 105 OMPLIANCE R&TTE D UROPEAN IRECTIVE Spectral regulations may require the TxD option to be installed in the transceiver. In this case, you cannot add channels with new transmit frequencies. You can, however, add receive-only channels, and channels with the same transmit frequency as an existing channel.

  • Page 106: Emc And Safety Notices

    OMPLIANCE AND SAFETY NOTICES EMC and safety notices Radiation safety (non-EU installations) To ensure optimal transceiver performance and to avoid exposure to excessive electromagnetic fields, the antenna system must be installed according to the instructions provided. WARNING: High voltages exist on the antenna during transmission and tuning.

  • Page 107: Emc

    To ensure that compliance with the EMC Directive is maintained. Use standard shielded cables supplied from Codan (where applicable). Ensure the covers for the equipment are fitted correctly. Cover unused connectors on the RF unit with the protective caps supplied to prevent electrostatic discharge passing through your transceiver.

  • Page 108: Earth Symbols

    OMPLIANCE AND SAFETY NOTICES To ensure electrical safety: Use the standard AC mains cable supplied. Ensure the covers for the equipment are fitted correctly. CAUTION: If it is necessary for a qualified electronics technician to remove the covers during servicing, they must be refitted correctly before using the equipment.

  • Page 109: Rcm Approval

    OMPLIANCE APPROVAL RCM approval The Envoy™ Transceiver meets the requirements of the Australian Communications and Media Authority: Radiocommunications (MF and HF equipment—Land Mobile Service) Standard 2003 (AS/NZS 4770) and Radiocommunications (HF CB and Handphone Equipment) Standard 2008 (AS/NZ 4355). Envoy™ Transceiver Getting Started Guide...
  • Page 110 OMPLIANCE APPROVAL This page has been left blank intentionally. Envoy™ Transceiver Getting Started Guide...
  • Page 111 NDEX Index Numerics channel adding 17 2221 finding 51 entering text 41 selecting 51 channel screen 49 Channel Test call advanced view 29 adding to contact 20 antenna channels manual tune 9 capacity 77 selecting 23 character-entry mode selecting 10 check box selecting/deselecting 43 basic view 29...
  • Page 112 NDEX adding Message call 21 adding Phone call 22 keypad 8 adding RFDS Emergency call 73 adding Selective call 20 adding Send Position call 20 language cooling 77 selecting 15 crosspatch operating mode 9 menu bar selecting an option 36 date menu structure setting 15...
  • Page 113 NDEX RF unit size 78 temperature 77 weight 78 text RFDS Emergency call editing 38 adding to contact 73 time setting 15 transceiver scan table installing 79 adding a channel 18 operating 47 scanning 52 switching off 48 pausing 53 switching on 48 switching on or off 52 screen...
  • Page 114 NDEX This page has been left blank intentionally. NDEX...
  • Page 115 ASIA PACIFIC (Head Office) EUROPE, MIDDLE-EAST & AFRICA AMERICAS Codan Limited Codan (UK) Ltd Codan US, Inc. 81 Graves Street Unit C4, Endeavour Place 1 Fishers Road Newton SA 5074 Coxbridge Business Park Pittsford NY 14534 AUSTRALIA Farnham Surrey GU10 5EH...

This manual is also suitable for:

Envoy 2230Envoy 2221

Table of Contents