Page 1 No part of this handbook may be reproduced, transcribed, translated into any language or transmitted in any form whatsoever without the prior written consent of Codan Pty Ltd. © Copyright 1997 Codan Pty Ltd. Codan part number 15-04076 Issue 1, 1997...
Page 3: Table Of Contents
Telephone directory creation ..........3-29 4 Using Setup mode procedures Using Setup mode............... 4-2 List of Setup mode procedures..........4-3 Advanced users..............4-7 5 Setup procedures—part 1 ALE alphanumeric address setup ........5-2 ALE option reset..............5-4 HF SSB transceiver reference manual...
Page 4 Power up address display on/off ........7-16 PTT release beep on/off............. 7-18 PTT transmit cutout ............7-20 Recall channels by frequency on/off ........7-22 RF gain on/off..............7-24 RS-232 connected equipment ..........7-26 RS-232 connection baud rate..........7-29 HF SSB transceiver reference manual...
Page 5 Setup mode availability on/off........... 9-11 Transceiver reset to factory settings........9-13 10 Display messages 11 Appendix Connectors................ 11-2 Connecting ancillary equipment........11-8 Using the optional RS-232/I C Interface ......11-10 Specifications..............11-14 Accessories ..............11-15 Index HF SSB transceiver reference manual...
Page 6 A typical mobile station........2-3 Figure 2.3 Rear view of control head without cover ..2-8 Figure 4.1 The Setup mode tree ........4-9 Figure 9.1 Moving the link for Link Setup mode ....9-2 HF SSB transceiver reference manual...
Page 7: About This Manual
1 About this manual This manual describes how you set up your Codan HF SSB transceiver. This issue of the manual incorporates operating information for software versions from: • transceiver (main) 4.00 • head (control) panel 4.00. You should refer to this manual when you want to: •...
Page 8 Chapter 11 covers technical information such as the connector pin arrangements, ancillary equipment settings, transceiver specifications, options and accessories. We recommend that only Codan approved service agents perform maintenance on the transceiver. HF SSB transceiver reference manual...
Page 9 Call the microphone button that you need to operate (the Call button in this example). The solid area in the picture of the microphone on the left shows you where to find the button. HF SSB transceiver reference manual...
Page 10 CICS Computer Interface Command Set. Depth. Decibel. Direct Current. EPROM types of Programmable Read-Only EEPROM Memory. BBPROM SEEPROM Global Positioning System. Height. High Frequency. Kilogram. Kilohertz. Loudspeaker. Liquid Crystal Display. Lower Sideband. Lower/Upper sideband selectable. HF SSB transceiver reference manual...
Page 11 Selective calls include beacon calls, selcalls, group calls, telcalls, GPS calls, page calls, ALE calls and status calls. Single Sideband transmission format. Standing Wave Ratio. HF SSB transceiver reference manual...
Page 12 (Codan part number 15-04073). For information on the features fitted to your transceiver, refer to the front of your HF SSB transceiver user guide for the list of factory fitted transceiver options. For information on ALE calling, refer to the 9300 ALE controller user guide (Codan part number 15-04046).
Page 13 Make sure that nothing is missing before starting installation. The procedures for installing your transceiver are not comprehensive. They are to be used as a guide only. We recommend that installation be carried out by qualified and experienced personnel. HF SSB transceiver reference manual...
Page 14: Installation
Mode 93XX SSB Transceiver Chan Chan Select USB/LSB Scan Tune Volume Emgcy S'Call Voice Call Mute Mute Earth point AC power supply CODAN XXXX Power Supply AC mains Figure 2.1 A typical fixed base station HF SSB transceiver reference manual...
Page 15: Figure 2.2 A Typical Mobile Station
CODAN Chan Chan Select USB/LSB Scan Tune Volume Emgcy S'Call Voice Call Mute Mute Extended control Automatic tuning transceiver whip antenna CODAN SSB Transceiver Coaxial and control cable Battery Figure 2.2 A typical mobile station HF SSB transceiver reference manual...
Page 16 200mm. The cables can be closer together for short distances, for example, to pass through the same hole in the bulkhead. Failure to observe this warning will cause distortion of the transmitted audio signals. HF SSB transceiver reference manual...
Page 17: Mounting The Transceiver
To mount the cradle: 1. Secure the mounting cradle in position with the rotating cam catches to the front. Ensure there is sufficient space at the rear of the cradle to clear the transceiver heat sink and connectors. HF SSB transceiver reference manual...
Page 18 3. Secure the adaptor plates flush to the transceiver side rails with the new screws provided, and fit one ‘O’ ring over each projecting stud. The projecting studs on the adaptor plates fit into the slides in the cradle. HF SSB transceiver reference manual...
Page 19 Installation 4. Insert the transceiver adaptor plates into the cradle slides and push fully into the cradle. 5. Secure the transceiver into the cradle with the spring clips. HF SSB transceiver reference manual...
Page 20: Mounting The Control Head And Loudspeaker
Avoid places exposed to direct sunlight such as the car dashboard close to the windscreen. Top entry cable path L/S loudspeaker socket 10-pin control cable connector Bottom entry cable path Figure 2.3 Rear view of control head without cover HF SSB transceiver reference manual...
Page 21 2. Secure the mounting cradle into position. Ensure that there is sufficient space at the rear for the cables. 3. Secure the equipment to the mounting cradle with the two screws and washers. HF SSB transceiver reference manual...
Page 22 When connecting the microphone, gently rotate the plug in the microphone socket until the pins locate. Push the plug home and fasten the locking ring until finger-tight. Do not over tighten. 2-10 HF SSB transceiver reference manual...
Page 23: Power Supply
200mm. The cables can be closer together for short distances, for example, to pass through the same hole in the bulkhead. Failure to observe this warning will cause distortion of the transmitted audio signals. HF SSB transceiver reference manual 2-11...
Page 24: Grounding
It may be necessary to remove paint from around the mounting screws to ensure a good contact. 2-12 HF SSB transceiver reference manual...
Page 25: Ancillary Equipment
• physical location • distance from the transceiver • grounding. Follow the installation instructions provided with each antenna and antenna tuner to achieve the best possible performance. HF SSB transceiver reference manual 2-13...
Page 26 Installation 2-14 HF SSB transceiver reference manual...
Page 27: Channel And Scan Table Setup
This chapter covers: • Channel creation and editing (3-2) • Channel creation in Free-Tune Receiver mode (3-17) • Channel deletion (3-21) • Scan table creation (3-22) • Scan table deletion (3-27) • Telephone directory creation (3-29). HF SSB transceiver reference manual...
Page 28: Channel Creation And Editing
You can change any unprotected channel setting. The only protected channel setting you can change is the channel comment. If you want to change the settings of a protected channel, make an unprotected copy of the channel and edit this copy. HF SSB transceiver reference manual...
Page 29 400 channels are available if only a few channel comments are used. 200 channels may be available if all channels have channel comments. HF SSB transceiver reference manual...
Page 30 • Yes if you want to create a channel number? channel by copying or Step 4. changing information from Step 6. this channel • No if you want to edit this channel (that is, save your changes to this channel). HF SSB transceiver reference manual...
Page 31 If this channel is protected, the display looks like this: To edit this channel, press Enter channel text Enter CLEAR ENTER R'call If this channel is unprotected, the display looks like this: Channel used Enter to continue. – EXIT ENTER HF SSB transceiver reference manual...
Page 32 For example, new value to enter 2040kHz, enter 204000. Entering a frequency automatically makes this a numeral button receive-only channel. Press Example of the display: Enter Options Enter R'call Upper sideband EXIT ENTER HF SSB transceiver reference manual...
Page 33 • U for upper sideband • L for lower sideband • LU for either sideband to be Select selectable. To move to the tone Example of the display: call group setting, Enter Options rotate Hi: 1320 Volume EXIT ENTER HF SSB transceiver reference manual...
Page 34 Enter Options rotate N o t p r o t e c t e d Volume EXIT ENTER Enter Options N o t p r o t e c t e d EXIT ENTER HF SSB transceiver reference manual...
Page 35 ENTER To enter a comment to Enter up to 20 characters (for example, Local Network). describe this channel, select each character To clear any existing text, using press Select and move between characters using Volume HF SSB transceiver reference manual...
Page 36 Channel and scan table setup Action Notes To save all changes for There is a pause before the the edited or copied display looks like this example: channel, press Geneva Switzerland 2040 Enter CALL R'call 3-10 HF SSB transceiver reference manual...
Page 37 DELETE ENTER Enter the number of Leave the number unchanged the channel if you want to edit channel information for this channel number instead of saving changes under a new channel numeral number. button HF SSB transceiver reference manual 3-11...
Page 38 Enter RX 2,040.0 R'call 2,040.0 EXIT ENTER To change the transmit Enter the kHz frequency to two frequency, enter the decimal places. new value To inhibit transmission on this channel, enter 0. numeral button 3-12 HF SSB transceiver reference manual...
Page 39 (From Step 8.) The display shows the channel options: Press Enter Options Enter Upper sideband R'call EXIT ENTER If you finish changing channel options at any time in steps 11–18, you can go to step 19. HF SSB transceiver reference manual 3-13...
Page 40 • T- to disallow tone calls on Select this channel. To move to the selcall Example of the display: group setting, rotate Enter Options Volume Self Id: – – – – – – Codan EXIT ENTER 3-14 HF SSB transceiver reference manual...
Page 41 EXIT ENTER To change the channel Select: protection setting, • NP to leave this channel rotate unprotected • P to protect this channel from all changes. Select Protection only applies when TXE is disabled. HF SSB transceiver reference manual 3-15...
Page 42 Select and move between characters using Volume To save all changes for There is a pause before the the channel, press display looks like this example: Geneva Switzerland Enter 2040 R'call CALL 3-16 HF SSB transceiver reference manual...
Page 43: Channel Creation In Free-Tune Receiver Mode
F r e e Tu n e R e c e i v e r 4,01000 until you see the display for Free-Tune Receiver mode. Make any changes to Refer to the HF SSB the frequency. transceiver user guide, Chapter 3, Using Free-Tune Receiver mode. Press...
Page 44 The display should look like this: Enter Enter Options R'call Upper sideband EXIT ENTER If you entered the number of a channel that already exists, the transceiver beeps. Start the procedure again by pressing 3-18 HF SSB transceiver reference manual...
Page 45 Caution! Once you protect a channel, only a Codan agent can change or delete this channel without deleting all channels from the transceiver. Press Example of the display: Enter channel text Enter R'call CLEAR ENTER HF SSB transceiver reference manual 3-19...
Page 46 Select and move between characters using Volume To return to Channel There is a pause before the mode saving the new display looks like this example: channel, press Radio Australia 4835 Enter R'call 3-20 HF SSB transceiver reference manual...
Page 47: Channel Deletion
Channel and scan table setup Channel deletion This procedure is used to delete unprotected channels. Only a Codan agent can change or delete a protected channel unless you have option TXE fitted. To delete an unprotected channel: Action Notes In Channel mode,...
Page 48: Scan Table Creation
Use Pause scanning if you expect voice calls and want scanning to pause for five seconds when voice is detected on the channel. Each channel is scanned for one second. Scanning also stops for selcalls. 3-22 HF SSB transceiver reference manual...
Page 49 In Channel mode, Example of the display: press Scan Table: Scan Press SCAN to Scan PROGRAM EXIT To select one of the Select scan table 1, 2 or 3. three scan tables, rotate Select HF SSB transceiver reference manual 3-23...
Page 50 To clear any existing text, using press Select and move between characters using Volume Press Example of the display: Scan Table: 2 Default Scan: Cont Continuous scan EXIT ENTER 3-24 HF SSB transceiver reference manual...
Page 51 To select the channel You can add up to ten to add to the scan table, channels to the scan table. rotate To delete a channel already added to the scan table, press Select HF SSB transceiver reference manual 3-25...
Page 52 Do you want to add another channel to the scan table? Step 9. Step 12. To save your changes, Example of the display: press Geneva Switzerland Scan 2040 CALL Return to Step 2 to program another scan table. 3-26 HF SSB transceiver reference manual...
Page 53: Scan Table Deletion
Select scan table 1, 2 or 3. three scan tables for deletion, rotate Select Press For example, scan table 2 looks like this: Scan Table: 2 F1 to delete table F2 to program table DELETE ENTER HF SSB transceiver reference manual 3-27...
Page 54 Channel and scan table setup Action Notes Press Example of the display: Scan Table: 2 Local Network F1 to delete table DELETE EXIT To delete the scan Example of the display: table, press Geneva Switzerland 2040 CALL 3-28 HF SSB transceiver reference manual...
Page 55: Telephone Directory Creation
(channels attached to a selcall group). To check the selcall group setting for a channel, refer to the HF SSB transceiver user guide, Chapter 3, Using View Channel Options mode. To add or clear entries from the telephone directory:...
Page 56 Edit Text Tel-Dir:3 Tel: 083050311 – – – – – – – – – – – – – – – – – – – – – – – – – – – – ENTER CLEAR 3-30 HF SSB transceiver reference manual...
Page 57 Volume To save your changes, Example of the display: press Ch: 149 Tel-Dir:3 Tel: 083050311 Codan Adelaide PROG CALL Do you want to add another telephone number? Return to Step 5. Step 12. HF SSB transceiver reference manual 3-31...
Page 58 Channel and scan table setup Action Notes To return to Channel Example of the display: mode, press Geneva Switzerland 2040 CALL 3-32 HF SSB transceiver reference manual...
Page 59: Using Setup Mode Procedures
• correspond to transceiver options factory fitted for your version of the transceiver in the HF SSB series range (refer to the front of your HF SSB transceiver user guide for the list of factory fitted transceiver options) • correspond to transceiver options that you have...
Page 60: Using Setup Mode
Channel mode. If this happens while you are in the middle of a procedure, start the procedure again. The descriptions for the procedures show examples of channel and frequency numbers. You must enter your own values. HF SSB transceiver reference manual...
Page 61: List Of Setup Mode Procedures
Using Setup mode procedures List of Setup mode procedures Procedures labelled standard are available in all HF SSB series transceivers. Procedure Page Setup Description code ALE alphanumeric 2434 Sets the alphanumeric address of your address transceiver. ALE option reset 2432 Resets 9 of the 17 ALE option settings 0–16...
Page 62 GPS location. GPS timeout on/off 6-23 3422 Switches on or off the GPS timeout warning. Page call canned 24441 Prepares and stores up to three messages message setup ready for sending in a page call. HF SSB transceiver reference manual...
Page 63 Identifies the equipment connected to either the RS-232 socket or GP connector on the equipment (standard) transceiver rear panel. RS-232 connection 7-29 3412 Sets the speed of information transfer for baud rate equipment connected to the transceiver rear (standard) panel. HF SSB transceiver reference manual...
Page 64 Sets up the high and low frequency pairs for (standard) any of the four tone call groups T1–T4. 99-beacon call 8-27 Switches on or off the ability to respond to response on/off received 99-beacon calls (selcalls ending in 99). HF SSB transceiver reference manual...
Page 65: Advanced Users
Setup mode, but some readers may find this knowledge useful. The Setup mode tree in Figure 4.1 shows how Setup mode procedures are accessed. Each menu of options displayed by the transceiver is represented by a branch in this tree. HF SSB transceiver reference manual...
Page 66: Figure 4.1 The Setup Mode Tree
Power up Display Display Display Display brightness contrast frequency diagnostics on/off (3421) on/off (3422) message mute address display (311) on/off on/off (34411) setting on/off (34413) (312) (313) (314) (34412) Figure 4.1 The Setup mode tree HF SSB transceiver reference manual...
Page 67 F1 to go back up the tree to the previous menu. For example, you could branch down to the Power Up menu and view each of the Power Up menu options, Message, Mute and Show ID, in turn making any changes to settings as necessary. HF SSB transceiver reference manual...
Page 68 Using Setup mode procedures 4-10 HF SSB transceiver reference manual...
Page 69: Setup Procedures-Part
Call privacy on/off (5-19) • Clock calibration* (5-21) • Clock setting* (5-23) • Clone a transceiver* (5-28). * indicates a standard procedure available in all HF SSB series transceivers (see Chapter 4, Using Setup mode procedures). HF SSB transceiver reference manual...
Page 70: Ale Alphanumeric Address Setup
Setup mode. Enter 2434 Example of the display: Alpha ALE ID – – – – – – – – – – – – – – – Enter ALE ID CLEAR PROGRAM numeral buttons HF SSB transceiver reference manual...
Page 71 Volume To save your change, The display shows: press ALE MENU 1–Options 2–Default 4–Alpha ID 3–Sound EXIT ENTER To return to Channel Example of the display: mode, press three times Geneva Switzerland 2040 CALL HF SSB transceiver reference manual...
Page 72: Ale Option Reset
Setup mode. Enter 2432 The display shows: Press ENTER to reset ALE system options EXIT ENTER numeral button Press The display shows: Press ENTER again to reset ALE options EXIT ENTER HF SSB transceiver reference manual...
Page 73 The transceiver beeps after press resetting all ALE options. The display shows: ALE MENU 1–Options 2–Default 3–Sound 4–Alpha ID EXIT ENTER To return to Channel Example of the display: mode, press three times Geneva Switzerland 2040 CALL HF SSB transceiver reference manual...
Page 74: Ale Option Settings
BER Threshold Golay Threshold Error Threshold ALE Silent Mode Call Retry Limit Channel Quality Averaging For further information, this manual should be read in conjunction with the 9300 ALE controller user guide (Codan part number 15-04046). HF SSB transceiver reference manual...
Page 75 For example, if the sounding signal length is set to 10 seconds and the scan group contains seven channels, the ALE station takes 70 seconds to complete sounding transmission. HF SSB transceiver reference manual...
Page 76 Golay testing is an additional method of error detection for ALE word transmission. The result of Golay error testing is used in the process of determining whether or not the ALE link can be established using the selected channel. HF SSB transceiver reference manual...
Page 77 When ALE Silent mode is switched on, the station will not: • recognise any incoming ALE calls • send or receive sounding signals even if Sounding On/Off (ALE option 0) is switched on. You can still send ALE calls in ALE Silent mode. HF SSB transceiver reference manual...
Page 78 Averaging reduces the effect that one bad reading may have on a perfect channel. If a new reading is better than an old value, the old value is replaced by the new reading. 5-10 HF SSB transceiver reference manual...
Page 79 17 ALE options (numbered 0–16). Select To select this ALE For example, option 13 (Call option, press Retry Limit) looks like this: ALE System Option: 13 Call retry limit EXIT ENTER HF SSB transceiver reference manual 5-11...
Page 80 Call retry limit EXIT ENTER Do you want to change another ALE option? Return to Step 3. Step 8. To return to Channel Example of the display: mode, press four times Geneva Switzerland 2040 CALL 5-12 HF SSB transceiver reference manual...
Page 81: Ale Sounding Interval
• 16 Hours. To change the ALE sounding time interval: Action Notes Repeatedly press The display shows: Mode SETUP MENU 1–Scan 2–Call 3–Config 4–More EXIT ENTER until you see the display for Setup mode. HF SSB transceiver reference manual 5-13...
Page 82 Select To save your change, The display shows: press ALE MENU 1–Options 2–Default 3–Sound 4–Alpha ID EXIT ENTER To return to Channel Example of the display: mode, press three times Geneva Switzerland 2040 CALL 5-14 HF SSB transceiver reference manual...
Page 83: Beep Loudness
The display looks like one of the following: Adjust Beep Volume NORMAL numeral Soft and loud beeps button EXIT ENTER Adjust Beep Volume SOFT Always soft beeps EXIT ENTER Adjust Beep Volume LOUD Always loud beeps EXIT ENTER HF SSB transceiver reference manual 5-15...
Page 84 • LOUD if you always want loud beeps. To save your change, The display shows: press CONFIG MENU 1–Display 2–Recall 3–Beeps 4–More EXIT ENTER To return to Channel Example of the display: mode, press twice Geneva Switzerland 2040 CALL 5-16 HF SSB transceiver reference manual...
Page 85: Call Preamble Length
To change the preamble length: Action Notes Repeatedly press The display shows: Mode SETUP MENU 1–Scan 2–Call 3–Config 4–More EXIT ENTER until you see the display for Setup mode. HF SSB transceiver reference manual 5-17...
Page 86 ALE controller to send Select calls. To save your change, The display shows: press CALL MENU 1–Beacon 2–Preamble 4–More 3–ALE EXIT ENTER To return to Channel Example of the display: mode, press twice Geneva Switzerland 2040 CALL 5-18 HF SSB transceiver reference manual...
Page 87: Call Privacy On/Off
0 like this: Enter Privacy Key Key: – – – – – numeral button EXIT ENTER If privacy is set, the privacy key is hidden like this: Setup Call Preamble ALE Preamble EXIT ENTER HF SSB transceiver reference manual 5-19...
Page 88 0 for the privacy key. numeral button To save your change, The display shows: press CALL MENU 1–Lockout 2–Emgcy 4–More 3–Privacy EXIT ENTER To return to Channel Example of the display: mode, press twice Geneva Switzerland 2040 CALL 5-20 HF SSB transceiver reference manual...
Page 89: Clock Calibration
SETUP MENU 1–Scan 2–Call 3–Config 4–More EXIT ENTER until you see the display for Setup mode. Enter 412 The display shows: TIME CALIBRATION Only use to adjust fast or slow clock EXIT ENTER numeral button HF SSB transceiver reference manual 5-21...
Page 90 Select above. To save your change, The display shows: press TIME SETUP MENU 2–Calib 1– Set EXIT ENTER To return to Channel Example of the display: mode, press twice Geneva Switzerland 2040 CALL 5-22 HF SSB transceiver reference manual...
Page 91: Clock Setting
2–Call 3–Config 4–More EXIT ENTER until you see the display for Setup mode. Enter 411 The clock stops running. Example of the display: TIME SETUP 16:01 D/M/Y 03/05/97 numeral Enter hours button EXIT ENTER HF SSB transceiver reference manual 5-23...
Page 92 16:01 D/M/Y 03/05/97 Enter minutes EXIT ENTER Enter the minutes if you want to change the minutes numeral button Press Example of the display: TIME SETUP 16:01 D/M/Y 03/05/97 Select date format EXIT ENTER 5-24 HF SSB transceiver reference manual...
Page 93 Enter the day for the D/M/Y format if you want to change the day (or month for the M/D/Y format) numeral button Press Example of the display: TIME SETUP 16:01 D/M/Y 03/05/97 Enter months EXIT ENTER HF SSB transceiver reference manual 5-25...
Page 94 To save all changes to The clock restarts at the time the F2 button is pressed. The the time and date, press display shows: TIME SETUP MENU 2–Calib 1– Set EXIT ENTER 5-26 HF SSB transceiver reference manual...
Page 95 Set calibration to zero clock for the first time, seconds/month. See Clock calibrate the clock. calibration on page 5-21. To return to Channel Example of the display: mode, press twice Geneva Switzerland 2040 CALL HF SSB transceiver reference manual 5-27...
Page 96: Clone A Transceiver
You can obtain the cable required for this procedure from an authorised Codan dealer (Codan part no. 08-05138-001). Except for the PIN, selcall group information and alphanumeric address, the cloning procedure overwrites all settings in the transceiver that you are copying to.
Page 97 4–More EXIT ENTER Mode until you see the display for Setup mode. Select 4-More by rotating Select Press The display shows: SETUP MENU 1–Time 2–Password 3–Clone 4–More EXIT ENTER Select 3-Clone by rotating Select HF SSB transceiver reference manual 5-29...
Page 98 After about two minutes, cloning finishes and the master transceiver beeps twice. The display shows: Please remove the cloning cable to return to the Setup Menu. Disconnect the cable and switch off both transceivers. 5-30 HF SSB transceiver reference manual...
Page 99: Setup Procedures-Part
Free-Tune Receiver mode availability on/off* (6-19) • GPS display on/off (6-21) • GPS timeout on/off (6-23). * indicates a standard procedure available in all HF SSB series transceivers (see Chapter 4, Using Setup mode procedures). HF SSB transceiver reference manual...
Page 100: Display Brightness
This procedure is used to change the brightness of the display. You can also adjust the brightness of the display using the On/Off button on the control panel (refer to the HF SSB transceiver user guide, Chapter 3, Adjusting the display brightness).
Page 101 Action Notes To save your change, The display shows: press DISPLAY MENU 1–Bright 2–Contrast 3–Format 4–dB Volt EXIT ENTER To return to Channel Example of the display: mode, press three times Geneva Switzerland 2040 CALL HF SSB transceiver reference manual...
Page 102: Display Contrast
This procedure is used to change the contrast of the display. You can also adjust the contrast of the display using the On/Off button on the control panel (refer to the HF SSB transceiver user guide, Chapter 3, Adjusting the display contrast).
Page 103 Action Notes To save your change, The display shows: press DISPLAY MENU 2–Contrast 1–Bright 3–Format 4–dB Volt EXIT ENTER To return to Channel Example of the display: mode, press three times Geneva Switzerland 2040 CALL HF SSB transceiver reference manual...
Page 104: Display Diagnostics On/Off
Setup mode. Enter 314 The display shows: dB Volt Test Display ENABLED Show dB Volt display EXIT ENTER numeral button dB Volt Test Display DISABLED Show normal display EXIT ENTER HF SSB transceiver reference manual...
Page 105 To save your change, The display shows: press DISPLAY MENU 2–Contrast 1–Bright 3–Format 4–dB Volt EXIT ENTER To return to Channel Example of the display: mode, press three times Geneva Switzerland 2040 CALL HF SSB transceiver reference manual...
Page 106: Display Frequency
To change how the channel frequency is displayed: Action Notes Repeatedly press The display shows: Mode SETUP MENU 2–Call 1–Scan 3–Config 4–More EXIT ENTER until you see the display for Setup mode. HF SSB transceiver reference manual...
Page 107 • INHIBIT to display no Select frequencies • RX ONLY to display receive frequency only. To save your change, The display shows: press DISPLAY MENU 1–Bright 2–Contrast 3–Format 4–dB Volt EXIT ENTER HF SSB transceiver reference manual...
Page 108 Setup procedures—Part 2 Action Notes To return to Channel Example of the display: mode, press three times Geneva Switzerland 2040 CALL 6-10 HF SSB transceiver reference manual...
Page 109: Emergency Selcall Receive Setup
To set up how you receive emergency selcalls: Action Notes Repeatedly press The display shows: Mode SETUP MENU 1–Scan 2–Call 3–Config 4–More EXIT ENTER until you see the display for Setup mode. HF SSB transceiver reference manual 6-11...
Page 110 RECEIVE-ALL and emergency selcalls SELECTIVE, rotate • RECEIVE-ALL to receive all emergency selcalls on channels scanned by the Select transceiver • SELECTIVE to receive emergency selcalls to your address and up to two additional addresses. 6-12 HF SSB transceiver reference manual...
Page 111 Step 6. Step 11. To select one of the two Example of the display: additional addresses, Emgcy S'call Rx ID: rotate Receive ID: – – – – – – EXIT PROGRAM Select HF SSB transceiver reference manual 6-13...
Page 112 EXIT PROGRAM Do you want to set up the other additional address? Return to Step 6. Step 11. To return to Channel Example of the display: mode, press three times Geneva Switzerland 2040 CALL 6-14 HF SSB transceiver reference manual...
Page 113: Emergency Selcall Transmit Setup
4–More EXIT ENTER until you see the display for Setup mode. Enter 24421 Example of the display: Emergency Selcall: Call address: – – – – – – Enter Emergency Adr CLEAR ENTER numeral button HF SSB transceiver reference manual 6-15...
Page 114 To select one of the Select any channel number 1 to four emergency channels, rotate Select Press Example of the display: Emergency Channel: 1 Channel: – – – – Enter Emgcy channel DELETE ENTER 6-16 HF SSB transceiver reference manual...
Page 115 USB and LSB • USB for upper sideband sideband settings (if • LSB for lower sideband. both available), rotate Select To save your setting, Example of the display: press Emergency Channel: Channel: EXIT PROGRAM HF SSB transceiver reference manual 6-17...
Page 116 Setup procedures—Part 2 Action Notes Do you want to set up another emergency channel? Return to Step 5. Step 12. To return to Channel Example of the display: mode, press four times Geneva Switzerland 2040 CALL 6-18 HF SSB transceiver reference manual...
Page 117: Free-Tune Receiver Mode Availability On/Off
Mode SETUP MENU 1–Scan 2–Call 3–Config 4–More EXIT ENTER until you see the display for Setup mode. Enter 3442 The display shows: Receive Frequencies ENABLED EXIT ENTER numeral button Receive Frequencies DISABLED EXIT ENTER HF SSB transceiver reference manual 6-19...
Page 118 To save your change, The display shows: press CONFIG MENU 1–PowerUp 2–Receiver 3–RF Gain 4–More EXIT ENTER To return to Channel Example of the display: mode, press twice Geneva Switzerland 2040 CALL 6-20 HF SSB transceiver reference manual...
Page 119: Gps Display On/Off
EXIT ENTER until you see the display for Setup mode. Enter 3421 The display shows: GPS Display ENABLED Display LAT and LONG EXIT ENTER numeral button GPS Display DISABLED GPS display disabled EXIT ENTER HF SSB transceiver reference manual 6-21...
Page 120 GPS information. To save your change, The display shows: press GPS MENU 1–Display 2–Timeout EXIT ENTER To return to Channel Example of the display: mode, press three times Geneva Switzerland 2040 CALL 6-22 HF SSB transceiver reference manual...
Page 121: Gps Timeout On/Off
OFF (no error beep). To switch on or off GPS timeout: Action Notes Repeatedly press The display shows: Mode SETUP MENU 1–Scan 2–Call 3–Config 4–More EXIT ENTER until you see the display for Setup mode. HF SSB transceiver reference manual 6-23...
Page 122 • a time in the range 5–35 minutes. Select To save your change, The display shows: press GPS MENU 1–Display 2–Timeout EXIT ENTER To return to Channel Example of the display: mode, press three times Geneva Switzerland 2040 CALL 6-24 HF SSB transceiver reference manual...
Page 123: Setup Procedures-Part
• RF gain on/off* (7-24) • RS-232 connected equipment* (7-26) • RS-232 connection baud rate* (7-29). * indicates a standard procedure available in all HF SSB series transceivers (see Chapter 4, Using Setup mode procedures). HF SSB transceiver reference manual...
Page 124: Page Call Canned Message Setup
Example of canned message 3: canned message, rotate Page Call Message: – – – – – – – – – – – – – – – – – – – – Press F2 to edit EXIT EDIT Select HF SSB transceiver reference manual...
Page 125 Call me – – – – – – – – – – – – – – Press F2 to edit EXIT EDIT Do you want to prepare another canned message? Return to Step 3. Step 8. HF SSB transceiver reference manual...
Page 126 Setup procedures—Part 3 Action Notes To return to Channel Example of the display: mode, press three times Geneva Switzerland 2040 CALL HF SSB transceiver reference manual...
Page 127: Password Entry To Enable Transceiver Options
By using passwords, you can purchase additional features for your transceiver without the need to return the unit to your Codan agent. You obtain passwords from your Codan agent. There is a separate password for each transceiver option. Passwords are unique to your transceiver. You cannot use your transceiver’s passwords with a different transceiver.
Page 128 – – – – – – – – – – – – EXIT ENTER You will need this ID when you contact your Codan agent. Contact your Codan The Codan agent will ask you agent and request the for personal identification and password for the your transceiver ID. transceiver option you want to enable.
Page 129 If the password is correct, the display shows the option as now enabled (for example, the GPS option): PASSWORD A630–9A00–0000–DD GPS Enabled EXIT ENTER To return to Channel Example of the display: mode, press Geneva Switzerland 2040 CALL HF SSB transceiver reference manual...
Page 130 You will need to obtain the PIN Deletion password from your Codan agent. This password allows you to delete the PIN when you switch on the transceiver. To delete a forgotten PIN:...
Page 131 – – – – – – – – – EXIT ENTER If the password is correct, the transceiver enters Channel mode after displaying this for 10 seconds: PASSWORD PIN deleted To set up a new PIN, see Chapter 9, PIN setup. HF SSB transceiver reference manual...
Page 132: Power Up Message On/Off
2–Call 1–Scan 3–Config 4–More EXIT ENTER until you see the display for Setup mode. Enter 34411 Example of the display: Power Up Message ENABLED EXIT PROG numeral button Power Up Message DISABLED EXIT ENTER 7-10 HF SSB transceiver reference manual...
Page 133 Modify message CLEAR ENTER If you selected DISABLED, the display shows: POWER UP MENU 1–Message 2–Mute 3–Show ID EXIT ENTER Did you select ENABLED to display a power up message? Step 6. Step 8. HF SSB transceiver reference manual 7-11...
Page 134 Volume To save your change, The display shows: press POWER UP MENU 1–Message 2–Mute 3–Show ID EXIT ENTER To return to Channel Example of the display: mode, press three times Geneva Switzerland 2040 CALL 7-12 HF SSB transceiver reference manual...
Page 135: Power Up Mute Setting
Chapter 8, Selcall mute availability on/off). To change the initial mute setting: Action Notes Repeatedly press The display shows: Mode SETUP MENU 2–Call 1–Scan 3–Config 4–More EXIT ENTER until you see the display for Setup mode. HF SSB transceiver reference manual 7-13...
Page 136 • SELCALL MUTE if you want selcall muting on power switch on. To save your change, The display shows: press POWER UP MENU 1–Message 2–Mute 3–Show ID EXIT ENTER 7-14 HF SSB transceiver reference manual...
Page 137 Setup procedures—Part 3 Action Notes To return to Channel Example of the display: mode, press three times Geneva Switzerland 2040 CALL HF SSB transceiver reference manual 7-15...
Page 138: Power Up Address Display On/Off
ENTER until you see the display for Setup mode. Enter 34413 The display shows: Power Up Self ID SHOW SELF ID EXIT ENTER numeral button Power Up Self ID HIDE SELF ID EXIT ENTER 7-16 HF SSB transceiver reference manual...
Page 139 To save your change, The display shows: press POWER UP MENU 1–Message 2–Mute 3–Show ID EXIT ENTER To return to Channel Example of the display: mode, press three times Geneva Switzerland 2040 CALL HF SSB transceiver reference manual 7-17...
Page 140: Ptt Release Beep On/Off
4–More EXIT ENTER until you see the display for Setup mode. Enter 3432 The display shows: PTT Beeps ENABLED Enable PTT beeps EXIT ENTER numeral button PTT Beeps DISABLED Disable PTT beeps EXIT ENTER 7-18 HF SSB transceiver reference manual...
Page 141 To save your change, The display shows: press CONFIG PTT MENU 1–Timer 2–PTT Beep 3–Auto Tune EXIT ENTER To return to Channel Example of the display: mode, press three times Geneva Switzerland 2040 CALL HF SSB transceiver reference manual 7-19...
Page 142: Ptt Transmit Cutout
• 35 mins. To set the PTT transmit cutout time: Action Notes Repeatedly press The display shows: Mode SETUP MENU 1–Scan 2–Call 3–Config 4–More EXIT ENTER until you see the display for Setup mode. 7-20 HF SSB transceiver reference manual...
Page 143 To save your change, The display shows: press CONFIG PTT MENU 1–Timer 2–PTT Beep 3–Auto Tune EXIT ENTER To return to Channel Example of the display: mode, press three times Geneva Switzerland 2040 CALL HF SSB transceiver reference manual 7-21...
Page 144: Recall Channels By Frequency On/Off
ENTER until you see the display for Setup mode. Enter 32 The display shows: Recall by Frequency ENABLED Enable freq recall EXIT ENTER numeral button Recall by Frequency DISABLED Disable freq recall EXIT ENTER 7-22 HF SSB transceiver reference manual...
Page 145 To save your change, The display shows: press CONFIG MENU 1–Display 2–Recall 3–Beeps 4–More EXIT ENTER To return to Channel Example of the display: mode, press twice Geneva Switzerland 2040 CALL HF SSB transceiver reference manual 7-23...
Page 146: Rf Gain On/Off
4–More EXIT ENTER until you see the display for Setup mode. Enter 3443 The display shows: RF Gain Control RF gain on EXIT ENTER numeral button RF Gain Control RF gain off EXIT ENTER 7-24 HF SSB transceiver reference manual...
Page 147 To save your change, The display shows: press CONFIG MENU 1–PowerUp 2–Receiver 3–RF Gain 4–More EXIT ENTER To return to Channel Example of the display: mode, press twice Geneva Switzerland 2040 CALL HF SSB transceiver reference manual 7-25...
Page 148: Rs-232 Connected Equipment
To change the setting for the equipment connected to the RS-232 socket or GP connector: Action Notes Repeatedly press The display shows: Mode SETUP MENU 2–Call 1–Scan 3–Config 4–More EXIT ENTER until you see the display for Setup mode. 7-26 HF SSB transceiver reference manual...
Page 149 • NONE if nothing is connected • COMPUTER if a Select computer is connected • GPS NMEA-0183 if a GPS receiver is connected • 9300 ALE if an ALE controller is connected. HF SSB transceiver reference manual 7-27...
Page 150 Setup procedures—Part 3 Action Notes To save your change, The display shows: press CONFIG RS232 MENU 1–Mode 2–Config EXIT ENTER To return to Channel Example of the display: mode, press three times Geneva Switzerland 2040 CALL 7-28 HF SSB transceiver reference manual...
Page 151: Rs-232 Connection Baud Rate
To set the baud rate for the RS-232 socket and GP connector: Action Notes Repeatedly press The display shows: Mode SETUP MENU 1–Scan 2–Call 3–Config 4–More EXIT ENTER until you see the display for Setup mode. HF SSB transceiver reference manual 7-29...
Page 152 300–9600. Select To save your change, The display shows: press CONFIG RS232 MENU 1–Mode 2–Config EXIT ENTER To return to Channel Example of the display: mode, press three times Geneva Switzerland 2040 CALL 7-30 HF SSB transceiver reference manual...
Page 153: Setup Procedures-Part
• Telcall availability on/off (8-22) • Tone call setup* (8-24) • 99-beacon call response on/off (8-27). * indicates a standard procedure available in all HF SSB series transceivers (see Chapter 4, Using Setup mode procedures). HF SSB transceiver reference manual...
Page 154: Scan Table Automatic Scanning Start
The display shows: Mode SETUP MENU 1–Scan 2–Call 3–Config 4–More EXIT ENTER until you see the display for Setup mode. Enter 11 Example of the display: Auto Scan Setup Time: Autoscan is Off EXIT ENTER numeral button HF SSB transceiver reference manual...
Page 155 • a delay in the range 1–10 minutes. Select To save your change, The display shows: press SCAN MENU 2–Enable 1–Auto EXIT ENTER To return to Channel Example of the display: mode, press twice Geneva Switzerland 2040 CALL HF SSB transceiver reference manual...
Page 156: Scan Table Editing On/Off
8-2). To switch on or off scan table editing: Action Notes Repeatedly press The display shows: Mode SETUP MENU 2–Call 1–Scan 3–Config 4–More EXIT ENTER until you see the display for Setup mode. HF SSB transceiver reference manual...
Page 157 • DISABLED to switch off scan table editing. Select To save your change, The display shows: press SCAN MENU 1–Auto 2–Enable EXIT ENTER To return to Channel Example of the display: mode, press twice Geneva Switzerland 2040 CALL HF SSB transceiver reference manual...
Page 158: Selcall Address Setup
You can set up any selcall group. To find out the selcall group assigned to each channel in the transceiver, refer to the HF SSB transceiver user guide, Chapter 3, Using View Channel Options mode. A selcall group for normal selective calling consists of: •...
Page 159 Setup procedures—Part 4 The selcall type describes the type of selcall group. For normal selective calling between stations, use the Codan selcall type. If you want to set up a selcall group for Radphone Direct Dialling (secure telcalls) use the RDD selcall type.
Page 160 RDD telcalls. numeral button Press Example of the display: Selcall Group: 1 Call Address: – – – – – – Enter Call Address EXIT ENTER HF SSB transceiver reference manual...
Page 161 Example of the display: Selcall Group: 1 Self ID: 1 2 3 4 Codan Select Selcall Type EXIT ENTER To select the selcall Select: type, rotate • Codan for normal selcalls • RDD for secure RDD telcalls. Select HF SSB transceiver reference manual...
Page 162 Example of the display: Selcall Group: 1 Self ID: 1 2 3 4 – – – – – – – – – – – – – – – – – – – – CLEAR ENTER 8-10 HF SSB transceiver reference manual...
Page 163 Self ID: 1 2 3 4 EXIT PROGRAM Selcall Group: Self ID: 1 2 3 4 Codan EXIT PROGRAM Do you want to set up another selcall group? Return to Step 3. Step 17. HF SSB transceiver reference manual 8-11...
Page 164 Setup procedures—Part 4 Action Notes To return to Channel Example of the display: mode, press four times Geneva Switzerland 2040 CALL 8-12 HF SSB transceiver reference manual...
Page 165: Selcall Address Size Compatibility
To set the address size compatibility: Action Notes Repeatedly press The display shows: Mode SETUP MENU 1–Scan 2–Call 3–Config 4–More EXIT ENTER until you see the display for Setup mode. HF SSB transceiver reference manual 8-13...
Page 166 6-digit addresses Select • 6-DIGIT-ONLY if all stations in your network are capable of using 6-digit addresses. To save your change, The display shows: press SELCALL MENU 1–ID 2–Mute 3–ID size EXIT ENTER 8-14 HF SSB transceiver reference manual...
Page 167 Setup procedures—Part 4 Action Notes To return to Channel Example of the display: mode, press three times Geneva Switzerland 2040 CALL HF SSB transceiver reference manual 8-15...
Page 168: Selcall Lockout On/Off
ENTER until you see the display for Setup mode. Enter 2441 The display shows: S'call Lockout Setup ENABLED Call lockout enabled EXIT ENTER numeral button S'call Lockout Setup DISABLED Call lockout disabled EXIT ENTER 8-16 HF SSB transceiver reference manual...
Page 169 To save your change, The display shows: press CALL MENU 1–Lockout 2–Emgcy 4–More 3–Privacy EXIT ENTER To return to Channel Example of the display: mode, press twice Geneva Switzerland 2040 CALL HF SSB transceiver reference manual 8-17...
Page 170: Selcall Mute Availability On/Off
4–More EXIT ENTER until you see the display for Setup mode. Enter 212 The display shows: Selcall Mute ENABLED Selcall mute enabled EXIT ENTER numeral button Selcall Mute DISABLED Selcall mute disabled EXIT ENTER 8-18 HF SSB transceiver reference manual...
Page 171 Select To save your change, The display shows: press SELCALL MENU 1–ID 2–Mute 3–ID size EXIT ENTER To return to Channel Example of the display: mode, press three times Geneva Switzerland 2040 CALL HF SSB transceiver reference manual 8-19...
Page 172: Status Call Availability On/Off
ENTER until you see the display for Setup mode. Enter 24442 The display shows: Status Call Setup ENABLED Status call enabled EXIT ENTER numeral button Status Call Setup DISABLED Status call disabled EXIT ENTER 8-20 HF SSB transceiver reference manual...
Page 173 – – – – – – – – – – EXIT To return to Channel Example of the display: mode, repeatedly press Geneva Switzerland 2040 CALL until you see the display for Channel mode. HF SSB transceiver reference manual 8-21...
Page 174: Telcall Availability On/Off
Setup code 22 This procedure is used to switch on or off the ability to send telcalls. For information on telcalls, refer to the HF SSB transceiver user guide, Chapter 4, Telcall. To switch on or off the ability to send telcalls:...
Page 175 Select To save your change, The display shows: press CALL MENU 1–Selcall 2–Telcall 3–Tone 4–More EXIT ENTER To return to Channel Example of the display: mode, press twice Geneva Switzerland 2040 CALL HF SSB transceiver reference manual 8-23...
Page 176: Tone Call Setup
4–More EXIT ENTER until you see the display for Setup mode. Enter 23 Example of the display: Tone Pair: Hi: – – – – Hz Low:– – – – Hz EXIT PROGRAM numeral button 8-24 HF SSB transceiver reference manual...
Page 177 300–2,800Hz. This will cancel existing settings. numeral button Press For example, a high frequency of 1400Hz looks like this: Tone Pair: Hi: 1 4 0 0 Hz Low:– – – – EXIT ENTER HF SSB transceiver reference manual 8-25...
Page 178 EXIT PROGRAM Do you want to set up another tone call group? Return to Step 3. Step 10. To return to Channel Example of the display: mode, press three times Geneva Switzerland 2040 CALL 8-26 HF SSB transceiver reference manual...
Page 179: 99-Beacon Call Response On/Off
3–Config 4–More EXIT ENTER until you see the display for Setup mode. Enter 241 Example of the display: 99Beacon Setup ENABLED 99Beacon enabled EXIT ENTER numeral button 99Beacon Setup DISABLED 99Beacon disabled EXIT ENTER HF SSB transceiver reference manual 8-27...
Page 180 99-beacon calls. To save your change, The display shows: press CALL MENU 1–Beacon 2–Preamble 3–ALE 4–More EXIT ENTER To return to Channel Example of the display: mode, press twice Geneva Switzerland 2040 CALL 8-28 HF SSB transceiver reference manual...
Page 181: Link Setup Mode
If you make a mistake and want to exit half way through a Link Setup procedure, press the F1 button on the control panel or PTT button on the microphone. This will return you to the start of Link Setup mode without making any changes. HF SSB transceiver reference manual...
Page 182: Link Setup Mode Enter/Exit
(bottom cover removed) showing 1 2 3 4 A B 1 2 3 4 A B bottom printed circuit board Parked Link setup position position Figure 9.1 Moving the link for Link Setup mode HF SSB transceiver reference manual...
Page 183 Pull it up gently to remove it. Switch on the The display shows: transceiver. LINK SETUP MENU 2–Inhibit 1–Pin 3–Antenna 4–Reset ENTER The transceiver only detects a changed link position when the transceiver is first switched on. HF SSB transceiver reference manual...
Page 184 Switch off the transceiver. Return the link to the original parked position. Replace the bottom You are now ready to switch cover and screws. on the transceiver and continue normal operation. HF SSB transceiver reference manual...
Page 185: Antenna Band Or Channel Control
(for example, add-on high power linear amplifiers). The following table provides the switching frequencies for the outputs. For further details, contact your Codan agent. Bandset 1 Bandset 2 frequency ranges...
Page 186 BAND SET 1, BAND • BAND SET 1 or BAND SET 2 and SET 2 if you want to CHANNEL, rotate control equipment by frequency band • CHANNEL if you want to Select control equipment by channel frequency. HF SSB transceiver reference manual...
Page 187 Link Setup mode Action Notes Press The display shows: LINK SETUP MENU 1–Pin 2–Inhibit 3–Antenna 4–Reset ENTER Exit Link Setup mode. See Link Setup mode enter/exit on page 9-2. HF SSB transceiver reference manual...
Page 188: Pin Setup
PIN. Do not forget your PIN! If you do, you will be unable to use the transceiver. You will have to obtain a password from Codan to delete the PIN. To set, change or cancel a PIN: Action...
Page 189 Is a PIN already set? Step 4. Step 6. Enter the current PIN numeral button Press The transceiver beeps twice and switches off if you enter the wrong PIN. Switch the transceiver on and repeat the procedure. HF SSB transceiver reference manual...
Page 190 Enter the new PIN again from Step 6. Press The display shows: LINK SETUP MENU 1–Pin 2–Inhibit 3–Antenna 4–Reset ENTER Exit Link Setup mode. See Link Setup mode enter/exit on page 9-2. 9-10 HF SSB transceiver reference manual...
Page 191: Setup Mode Availability On/Off
The display shows: LINK SETUP MENU 2–Inhibit 1–Pin 3–Antenna 4–Reset ENTER Enter 2 The display shows: Setup Mode ENABLED Enable setup mode EXIT ENTER numeral button Setup Mode DISABLED Disable setup mode EXIT ENTER HF SSB transceiver reference manual 9-11...
Page 192 Setup mode • DISABLED to prevent use of Setup mode. Select Press The display shows: LINK SETUP MENU 1–Pin 2–Inhibit 3–Antenna 4–Reset ENTER Exit Link Setup mode. See Link Setup mode enter/exit on page 9-2. 9-12 HF SSB transceiver reference manual...
Page 193: Transceiver Reset To Factory Settings
(full transceiver reset to factory condition). Think carefully before deleting all channels since this includes all your protected channels set up by Codan! If you delete all channels and your transceiver is not fitted with the option TXE, you will be unable to use the transceiver until your transmit channels are entered again by Codan.
Page 194 • Reset user settings to Select factory defaults—to reset user settings but not channels • Reset user settings, delete all channels—to reset user settings and all channels—full transceiver reset. Use with caution! 9-14 HF SSB transceiver reference manual...
Page 195 To exit this procedure without resetting anything, press To start the reset, press The display shows: LINK SETUP MENU 1–Pin 2–Inhibit 3–Antenna 4–Reset ENTER Exit Link Setup mode. See Link Setup mode enter/exit on page 9-2. HF SSB transceiver reference manual 9-15...
Page 196 Link Setup mode 9-16 HF SSB transceiver reference manual...
Page 197: 10 Display Messages
This chapter lists all messages that are shown on the transceiver display. These include: • transceiver status messages • operator error messages • system error messages. Some error messages are accompanied by one or more beeps. HF SSB transceiver reference manual 10-1...
Page 198 Bad ALE SCall A channel in the ALE scan Assign a selcall group (S1–S5) channel table has not been assigned to this ALE selcall channel. See to a selcall group. Chapter 8, Selcall address setup. 10-2 HF SSB transceiver reference manual...
Page 199 RAM. Call stack There are no calls stored in Refer to the HF SSB transceiver empty the call memory. user guide, Chapter 5, Reviewing calls held in memory. Channel not This channel number is not Select a channel that exists.
Page 200 Clarify by using the Select knob Clarifier Clarifier mode has been selected. on the control panel. Refer to the HF SSB transceiver user guide, Chapter 3, Using Clarifier mode. Cloning failed Cloning the transceiver has Check the programming cables. failed.
Page 201 The transceiver failed to set Try sending another ALE call. up an ALE link. The call For details on ALE, see has failed. Chapter 5, ALE option settings. Contact your Codan agent if you need help. HF SSB transceiver reference manual 10-5...
Page 202 Codan agent for help. No destination No address to call has been Refer to the HF SSB transceiver set up. user guide, Chapter 4, Selcall for how to enter the address of the station you want to call.
Page 203 The antenna has not been tuned. the antenna. Option not This option has not been If you want this option, contact fitted enabled in the transceiver. your Codan agent. Page call A page call was None. succeeded acknowledged. HF SSB transceiver reference manual 10-7...
Page 204 If the problem remains, contact your Codan agent for help. S’call mute Selcall mute availability is To make selcall mute available, disabled switched off. see Chapter 8, Selcall mute availability on/off. 10-8 HF SSB transceiver reference manual...
Page 205 Meaning Action Scan abort Scanning has stopped To exit Scan mode, refer to the because the PTT or HF SSB transceiver user guide, another button was pressed. Chapter 3, Scanning for incoming calls. Scan inhibited Scan table editing is not To allow scan tables to be edited, currently allowed.
Page 206 Contact your Codan agent for unknown data error. help. Unlock error VC01 is unlocked. Contact your Codan agent for VC01 help. Unlock error VC01 and VC02 are Contact your Codan agent for VC01&2 unlocked. help. 10-10 HF SSB transceiver reference manual...
Page 207 Enter the correct number. small. Writing SEE Now reprogramming serial None. defaults PROM with default settings. Out of PA A channel has a frequency Contact your Codan agent for range outside the PA operating help. frequency band. HF SSB transceiver reference manual 10-11...
Page 208 Display messages 10-12 HF SSB transceiver reference manual...
Page 209: 11 Appendix
(11-8) • explains how to use the optional RS-232/I C Interface to connect combinations of ancillary equipment (11-10) • lists the transceiver specifications (11-14) • lists the accessories available for the transceiver (11-15). HF SSB transceiver reference manual 11-1...
Page 210: Connectors
This section covers: • the microphone socket • the Antenna Control connector • the Remote Control connector • the GP connector • the RS232 socket • the loudspeaker L/S socket • the Ext Alarm socket. 11-2 HF SSB transceiver reference manual...
Page 211 Key reference 4 3 7 2 1 6 5 Function Loudspeaker audio output Microphone input Ground Data in PTT in (active low) and data out Battery (switched) Front panel speaker (ground return) HF SSB transceiver reference manual 11-3...
Page 212 Tune in and out (active low) Scan antenna (active low) Not used Not used PTT out (+10V=Tx) Binary coded decimal channel 1 Binary coded decimal channel 2 Tuned in Battery (switched) Battery (switched) Ground Ground 11-4 HF SSB transceiver reference manual...
Page 213 Data (I C bus, 5V) Not used Clock (I C bus, 5V) Rx and Tx indicator Ground Ground Transmitter audio input Receiver demodulated output Receiver audio output Interrupt (I C bus, 5V) Battery (switched) HF SSB transceiver reference manual 11-5...
Page 214 It is used for ALE controllers, modems and fax interfaces. reference Remote Control Alarm 4 5 6 Function Ground Receiver output Transmitter input Quiet line Alarm input PTT input (active low) Scan Battery (switched) RS-232 receive RS-232 transmit 11-6 HF SSB transceiver reference manual...
Page 215 Speaker audio output Sleeve Ground External alarm socket The external alarm socket is labelled Ext Alarm. It is located at the right of the back panel. Connection Function Relay switch contact Sleeve Relay switch contact (ground) HF SSB transceiver reference manual 11-7...
Page 216: Connecting Ancillary Equipment
RS-232 connected equipment and RS-232 connection baud rate. If you want to connect a combination of ALE controllers, computers and GPS receivers, you will need to use the optional RS-232/I C Interface described on page 11-10. 11-8 HF SSB transceiver reference manual...
Page 217 Ext Alarm socket External alarm RS-232 socket Set RS-232 setting to GPS GPS receiver NMEA-0183 and baud rate to the value used by the GPS receiver (typically 4800). IPC-500 telephone Remote Control interconnect connector HF SSB transceiver reference manual 11-9...
Page 218: Using The Optional Rs-232/I C Interface
C switch is only used if a second interface is connected • the GPS A and GPS B switches set the baud rate for GPS socket • the COMP A and COMP B switches set the baud rate for the COMPUTER socket. 11-10 HF SSB transceiver reference manual...
Page 219 COMP A COMP B switch switch 9600 baud (no parity, 1 stop bit) 4800 baud (no parity, 1 stop bit) 2400 baud (no parity, 1 stop bit) 1200 baud (no parity, 1 stop bit) HF SSB transceiver reference manual 11-11...
Page 220 Step 6. (only the On or Off position Step 8. may be marked). Set the COMP switch The off position enables the to the off position. socket. 11-12 HF SSB transceiver reference manual...
Page 221 Remote Control connector of the first interface. Make sure that the I C switches are not set to the same position for both units. Set one to the on position and the other to the off position. HF SSB transceiver reference manual 11-13...
Page 222: Specifications
Appendix Specifications Channel capacity Refer to the front of the HF SSB transceiver user guide. Frequency range Refer to the front of the HF SSB transceiver user guide. Operating mode Refer to the front of the HF SSB transceiver user guide.
Page 223: Accessories
RS-232 facilities for GPS and computer connection. 2051 Service manual for this series of transceivers. 9366 Control head complete with hand PTT/key-pad control microphone and 6 metres of interface similar cable fitted with connectors for 9360 or similar. HF SSB transceiver reference manual 11-15...
Page 224 Appendix 11-16 HF SSB transceiver reference manual...
Page 225: Index
11-4 external alarm 11-7 —B— 7-20, 7-26, 7-29, 11-6 loudspeaker 11-7 battery power supply 2-11 microphone 11-3 beep loudness 5-15 remote control 11-5 brightness of display RS-232 7-26, 7-29, 11-7 contrast of display HF SSB transceiver reference manual Index-1...
Page 226 10-1 canned page call fixed base station full list 10-1 Free-Tune Receiver mode on power up 7-10 availability on/off 6-19 microphone connector 11-3 creating receive-only channels 3-17 mobile station Index-2 HF SSB transceiver reference manual...
Page 227 11-2 recall channels by frequency on/off 7-22 —T— receive frequency telcall availability on/off 8-22 release beep for PTT 7-18 telephone directory creation 3-29 remote control connector 11-5 tone call setup 8-24 reset HF SSB transceiver reference manual Index-3...
Page 228 7-20 accessories 11-15 transmit frequency cloning 5-28 troubleshooting messages 10-1 grounding 2-12 TXE option 3-4, 3-11 mounting —U— options reset 9-13 using the transceiver See user guide using See user guide Index-4 HF SSB transceiver reference manual...

Codan HF SSB Reference Manual

1 About this Manual

2 Installation

3 Channel and Scan Table Setup

4 Using Setup Mode Procedures

5 Setup Procedures-Part

6 Setup Procedures-Part

7 Setup Procedures-Part

8 Setup Procedures-Part

9 Link Setup Mode

10 Display Messages

11 Appendix

Index

Quick Links

Need help?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Codan HF SSB

Summary of Contents for Codan HF SSB

Table of Contents