Specifications - Milwaukee M12 FUEL ONEFTR12 Operator's Manual

SYMBOLOGY
Volts
Direct Current
No Load Revolutions per Minute (RPM)
Regulatory Compliance mark (RCM).
This product meets applicable
regulatory requirements.
Read Operator's Manual
ADDITIONAL BATTERY SAFETY RULES
WAR NIN G
To reduce the risk of fire,
personal injury , and product damage due to a
circuit, never immerse your tool, battery pack or
charger in fluid or allow a fluid to flow inside them.
Corrosive or conductive fluids, such as seawater ,
certain industrial chemicals, and bleach or bleach-
containing products, etc., can cause a short circuit.

SPECIFICATIONS

Volts............................................................ 12V DC
Battery Type .................................................M12™
Charger Type................................................M12™
Coin Cell Battery...................................3V CR2032
RPM ............................................................... 0-100
Recommended Ambient
Operating Temperature ...................... -17°C to 51°C
Recommended Operating
Humidity Percentage ...................0% or up to 90%
Cat. No. ........................................ M12 ONEFTR38
Torque Range .........................................13-135Nm
Square Drive Anvil ............................................ 3/8"
Cat. No. ........................................ M12 ONEFTR12
Torque Range .........................................16-203Nm
Square Drive Anvil ............................................ 1/2"
ASSEMBLY
Recharge only with the charger
WARNING
specified for the battery. For spe-
cific charging instructions, read the operator's
manual supplied with your charger and battery.
Removing/Inserting the Battery
To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
Always remove battery pack before
WARNING
changing or removing accessories.
To insert the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
Only use accessories specifically
WARNING
recommended for this tool. Others
may be hazardous.
Battery Indicator
The battery indicator
charge left in the battery pack. The battery indicator
will stay lit during operation.
Charge the battery when battery indicator
shown. NOTE: Tool will shut off when the battery has
depleted.
Use only sockets and other acces-
WARNING
sories specifically designed for
use on this tool. Other sockets and accessories
might shatter or break causing injury.
Attaching and Removing Accessories
These tools are intended only for use with acces-
sories designed for torque wrenches. Other sockets
could shatter or break, causing injury.
Non-Condensing
displays the amount of
1. Use only appropriate Square Drive Sockets.
2. To attach a socket or other accessory, align the
accessory with the drive anvil and push it firmly
onto the tool.
3. To remove the accessory, pull the accessory off
the drive anvil.
To navigate throughout the menu guide
arrow buttons
function within each category select the
Use exit button
Description
Modes
Saved Events Allow for grouping events and to
Grouping
View Recent
History
Settings
Units
Sound &
Haptics
Screen
Brightness
Screen Display Select light or dark backlight display.
Language
Rundown
Torque
About
Certification
Count
Firmware
Modes
Use the modes function to set up a profile quickly
within a couple of steps. Within the modes option: set
up units, target torque and percentage range. Once
the mode is selected: apply, edit or delete a mode.
Saved Events / Grouping
Save events to use at a later date. Storing in a group
will make it easier to recall preset specifications. The
tool will not automatically save events. From the main
is
screen, use the left and right arrows
the save button
saved events within the group. Press and hold the
save button for 3 seconds.
To learn more about the ONE-KEY™ function-
ality for this tool, please reference the Quick
Start guide included with this product or go to
onekey.milwaukeetools.com.au.
the ONE-KEY™ app, visit the App Store or Google
Play from your smart device.
4
Menu Guide
to modify settings. To set a
to exit each page.
Function
Add preset functions to a profile
setup units, target torque, and a
percentage range.
view recent history. (See "Saved
Events/Grouping" section.)
Organise events by saving to an
open group. (See "Saved Events/
Grouping" section.)
Recall recent history from a previous
time frame.
View sub categories within the set-
tings function.
Select units; ft-lbs, in-lbs, Nm and
kg-cm
Change ON/OFF options to light,
sound and haptics.
Select between Low, Medium and
High screen brightness modes.
Change the language setting; be-
tween English, French, Spanish, etc.
Add a percentage to the total se-
lected torque. Tool will stop at or
near the percentage allowing user
to hand tighten for full torque. (See
"Adjusting rundown torque")
General information for a certification
count and firmware
Display the last certified date and
a count until the next certification is
required. (See "Certification" section
for more information.)
Displays firmware version and tool
part number.
. To open a group and include
ONE-KEY™
, use the
button.
OK
and select
To download