Summary of Contents for Sunrise Medical Sedeo Pro Omni 2
Page 1
Omni 2 – Sedeo Pro Retro Fitting Help Guide CONFIDENTIAL: For internal use only. CONFIDENTIAL: For internal use only.
Page 2
OMNI 2 – SEDEO PRO RETRO FITTING HELP GUIDE Parts Required: Electronics • Omni 2 Kit – 20011242 (includes Input Section, Display Screen, 250cm connecting cable) Bag Mounting • Backpack – 20009190-010 • R-Net Bus. Cable – 20011035 • Fixing Bracket – 22509144 Joystick Mounting (Left and Right) •...
Page 3
OMNI 2 – SEDEO PRO RETRO FITTING HELP GUIDE Parts Required: CONFIDENTIAL: For internal use only. CONFIDENTIAL: For internal use only.
Page 4
OMNI 2 – SEDEO PRO RETRO FITTING HELP GUIDE Step 1 • Open the Omni 2 backpack so you can see the holes in the metal plate inside. CONFIDENTIAL: For internal use only. CONFIDENTIAL: For internal use only.
Page 5
OMNI 2 – SEDEO PRO RETRO FITTING HELP GUIDE Step 2 • Use a drill with a 5mm bit to drill holes through the fabric CONFIDENTIAL: For internal use only. CONFIDENTIAL: For internal use only.
Page 6
OMNI 2 – SEDEO PRO RETRO FITTING HELP GUIDE Step 3 • Drill the holes in positions shown below. CONFIDENTIAL: For internal use only. CONFIDENTIAL: For internal use only.
Page 7
OMNI 2 – SEDEO PRO RETRO FITTING HELP GUIDE Step 4 • Remove the 4 bolts that secure the backrest mounting brackets to the channels in the seat frame. Be careful not to lose the channel nuts. CONFIDENTIAL: For internal use only. CONFIDENTIAL: For internal use only.
Page 8
OMNI 2 – SEDEO PRO RETRO FITTING HELP GUIDE Step 5 • Remove the backrest completely as this makes the job easier. CONFIDENTIAL: For internal use only. CONFIDENTIAL: For internal use only.
Page 9
OMNI 2 – SEDEO PRO RETRO FITTING HELP GUIDE Step 6 • Attach the top backpack mounting bracket to the backrest mounting plates with 4 bolts in the orientation show below. CONFIDENTIAL: For internal use only. CONFIDENTIAL: For internal use only.
Page 10
OMNI 2 – SEDEO PRO RETRO FITTING HELP GUIDE Step 7 • This is how it should look once fixed. Don’t over tighten the bolts at this point. CONFIDENTIAL: For internal use only. CONFIDENTIAL: For internal use only.
Page 11
OMNI 2 – SEDEO PRO RETRO FITTING HELP GUIDE Step 8 • Fix the lower bracket in the same way and in the same orientation. CONFIDENTIAL: For internal use only. CONFIDENTIAL: For internal use only.
Page 12
OMNI 2 – SEDEO PRO RETRO FITTING HELP GUIDE Step 9 • This is what it should look like once fitted. Before tightening the bolts push the brackets high on the back post channels then tighten. CONFIDENTIAL: For internal use only. CONFIDENTIAL: For internal use only.
Page 13
OMNI 2 – SEDEO PRO RETRO FITTING HELP GUIDE Step 10 • Fix the bag to the bracket using 4 small screws, washers and nuts. The nuts secure on the inside of the bag. CONFIDENTIAL: For internal use only. CONFIDENTIAL: For internal use only.
Page 14
OMNI 2 – SEDEO PRO RETRO FITTING HELP GUIDE Step 11 • This is how the backpack should look once fitted. CONFIDENTIAL: For internal use only. CONFIDENTIAL: For internal use only.
Page 15
OMNI 2 – SEDEO PRO RETRO FITTING HELP GUIDE Step 12 • Remove the Velcro pad from inside the backpack. CONFIDENTIAL: For internal use only. CONFIDENTIAL: For internal use only.
Page 16
OMNI 2 – SEDEO PRO RETRO FITTING HELP GUIDE Step 13 • Take the Input Module and stick the Velcro pad centrally onto the back. CONFIDENTIAL: For internal use only. CONFIDENTIAL: For internal use only.
Page 17
OMNI 2 – SEDEO PRO RETRO FITTING HELP GUIDE Step 14 • Fix the Input Module to the Velcro pad inside the backpack. Leave enough room to connect the R-Net Bus. loom on the left hand side. CONFIDENTIAL: For internal use only. CONFIDENTIAL: For internal use only.
Page 18
OMNI 2 – SEDEO PRO RETRO FITTING HELP GUIDE Step 15 • Take the Omni mounting bracket (Fixed or Swing away). Remove the standard joystick mounting bracket. CONFIDENTIAL: For internal use only. CONFIDENTIAL: For internal use only.
Page 19
OMNI 2 – SEDEO PRO RETRO FITTING HELP GUIDE Step 16 • Fix the Omni 2 mounting piece to the swing away mount. Secure with fixing bolt. CONFIDENTIAL: For internal use only. CONFIDENTIAL: For internal use only.
Page 20
OMNI 2 – SEDEO PRO RETRO FITTING HELP GUIDE Step 17 • Fit 2 channel nuts to the bottom of the swing away mount using two bolts. CONFIDENTIAL: For internal use only. CONFIDENTIAL: For internal use only.
Page 21
OMNI 2 – SEDEO PRO RETRO FITTING HELP GUIDE Step 18 • Remove the front armpad fixing bolt. CONFIDENTIAL: For internal use only. CONFIDENTIAL: For internal use only.
Page 22
OMNI 2 – SEDEO PRO RETRO FITTING HELP GUIDE Step 19 • Slide swing away mount into the channels under the armpad and replace the armpad fixing bolt. CONFIDENTIAL: For internal use only. CONFIDENTIAL: For internal use only.
Page 23
OMNI 2 – SEDEO PRO RETRO FITTING HELP GUIDE Step 20 • Secure the fixing bolts into the channel nuts. It is easier to remove the swing away section to access the bolts. Once tightened, refit the swing away mount. CONFIDENTIAL: For internal use only.
Page 24
OMNI 2 – SEDEO PRO RETRO FITTING HELP GUIDE Step 21 • Remember to fit the bolt back into the bottom. CONFIDENTIAL: For internal use only. CONFIDENTIAL: For internal use only.
Page 25
OMNI 2 – SEDEO PRO RETRO FITTING HELP GUIDE Step 22 • Take one of the Link-It base module and fit on to Hexagon adapter. CONFIDENTIAL: For internal use only. CONFIDENTIAL: For internal use only.
Page 26
OMNI 2 – SEDEO PRO RETRO FITTING HELP GUIDE Step 23 • Fit the connecting rod into the base module and fit the second base module to the connecting rod. CONFIDENTIAL: For internal use only. CONFIDENTIAL: For internal use only.
Page 27
OMNI 2 – SEDEO PRO RETRO FITTING HELP GUIDE Step 24 • Take the Omni 2 Display Module and fix the Link-It adapter bracket with 2 small bolts. CONFIDENTIAL: For internal use only. CONFIDENTIAL: For internal use only.
Page 28
OMNI 2 – SEDEO PRO RETRO FITTING HELP GUIDE Step 25 • Fix the Omni 2 Display to the top Link-It base module. CONFIDENTIAL: For internal use only. CONFIDENTIAL: For internal use only.
Page 29
OMNI 2 – SEDEO PRO RETRO FITTING HELP GUIDE Step 26 • Position the Omni 2 Display and tighten the Link-It base module with a 5mm Allen Key. CONFIDENTIAL: For internal use only. CONFIDENTIAL: For internal use only.
Page 30
OMNI 2 – SEDEO PRO RETRO FITTING HELP GUIDE Step 27 • Take the Omni 2 display connecting cable and plug one end into the DISP port on the Input Module in the backpack. CONFIDENTIAL: For internal use only. CONFIDENTIAL: For internal use only.
Page 31
OMNI 2 – SEDEO PRO RETRO FITTING HELP GUIDE Step 28 • Connect the other end of the connecting cable to the port in the bottom of the Omni 2 Display Module. CONFIDENTIAL: For internal use only. CONFIDENTIAL: For internal use only.
Page 32
OMNI 2 – SEDEO PRO RETRO FITTING HELP GUIDE Step 29 • Connect the 30cm R-Net bus. cable to the port on the left side of the Omni 2 input module. CONFIDENTIAL: For internal use only. CONFIDENTIAL: For internal use only.
Page 33
OMNI 2 – SEDEO PRO RETRO FITTING HELP GUIDE Step 30 • Use the cable tidy clips to secure the connecting cable to the Link-It connecting rod. CONFIDENTIAL: For internal use only. CONFIDENTIAL: For internal use only.
Page 34
OMNI 2 – SEDEO PRO RETRO FITTING HELP GUIDE Step 31 • Tidy the connecting cables using clips and Velcro. Loop any excess connecting cable using the Velcro in the backpack. CONFIDENTIAL: For internal use only. CONFIDENTIAL: For internal use only.
Page 35
OMNI 2 – SEDEO PRO RETRO FITTING HELP GUIDE Step 32 • Plug the charging cable into the port on the right hand side of the Omni 2 Input Module. CONFIDENTIAL: For internal use only. CONFIDENTIAL: For internal use only.
Page 36
OMNI 2 – SEDEO PRO RETRO FITTING HELP GUIDE Step 33 • Connect the Omni 2 Input Module into the R-Net bus. system. CONFIDENTIAL: For internal use only. CONFIDENTIAL: For internal use only.