PIKO 35028 Quick Start Manual

PIKO 35028 Quick Start Manual

R/c analog power set
Hide thumbs Also See for 35028:

Advertisement

Quick Links

35028 R/C Analog Power Set

1. Contents:

• Pocket remote (Transmitter)
• 22 V DC 5 A Safety-Approved 120 V Power Supply
• R/C Analog DC Controller (Receiver)
• DC adapter cable for power supply

1.1 Technical data

Transmitter (Pocket Remote)
Number of channels: 8
Frequency range:
2.4 GHz
Range approx.:
30 m
Power supply:
1x 3 V CR2025
Weight approx.:
30 g
Receiver (R/C Analog DC Controller)
Number of channels: 8
Speed steps:
28 (14 steps if supplied with 7-16 V input)
Frequency range:
2.4 GHz
Range approx.:
30 m
Power supply:
16-24 V DC
Max. current:
4.5 A Max to Track
2 A Max for Accessories; 5 A Max Combined
Weight approx.:
150 g
Power Supply
Input:
100 – 240 V AC
Output:
22 V DC 5 A
Weight approx.
300 g
FOR INDOOR USE ONLY

2. Installation and Connection:

Connect the track power clamps and any DC accessories (switch control
boxes, lights, etc.) to the correct terminals on the back of the R/C Controller
(1). Connect the "pigtail" power cord adapter to the input terminals on the
back of the R/C Controller. Note the correct polarity of the wires (2). Con-
nect the pigtail to the plug on the power supply (3). Make sure to have an
operating Pocket Remote set to the same channel as the R/C Controller
and in-hand to immediately control operation. Then, after confirming that
all connections are correct and secure, plug the power supply into a 120V
grounded AC outlet (4).

3. Channel Selection

To communicate with each other, the R/C Controller (Receiver) and Pocket
Remote (Transmitter) must both be set to the same channel. They are
factory set to channel 0, but any one of the 8 channels, numbered 0-7, may
be selected.
Up to 8 sets of R/C Controllers and Pocket Remotes can operate in the
same area without interference by setting each set to a different channel.
Or, one Pocket Remote can operate up to 8 R/C Controllers by setting
them all to the same channel.
If using a 35040 Loco Receiver in the same area, keep in mind that this
operates in the same channel range. And it may be necessary to use a
different channel to avoid interference with other nearby radio devices in
the 2.4GHz radio range.
R/C Controller (Receiver):
1. Lift up the clear plastic lid on the R/C Controller.
2. Pull off the cover.
3. Now you have access to the DIP rotary switch.
4. The direction of the arrow indicates the channel that has been set.
5. Use a small flat screwdriver to set the channel on the DIP turn switch.
Pocket Remote (Transmitter):
1. Remove the small cover on the back of the Pocket Remote.
2. You now have access to the DIP rotary switch.
3. The arrow direction indicates the set channel.
4. You can adjust the channel by turning it with a small flat screwdriver.
#35270 Power Clamp
(not included)
black
120 V~ AC

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 35028 and is the answer not in the manual?

Questions and answers

Summary of Contents for PIKO 35028

  • Page 1 35028 R/C Analog Power Set 1. Contents: • Pocket remote (Transmitter) #35270 Power Clamp • 22 V DC 5 A Safety-Approved 120 V Power Supply (not included) • R/C Analog DC Controller (Receiver) • DC adapter cable for power supply 1.1 Technical data...
  • Page 2 5. General information Thank you for purchasing the PIKO R/C system for radio operation of your trains. Please read these operating instructions carefully in order to be able to use all the functions of this device. It is essential that you observe the following safety and warning instructions to ensure trouble-free and safe operation.

Table of Contents